KLARSTEIN 10030743 Fireplace Heater Instruction Manual

BASEL | COLMAR
Fireplace Heater
10030743 10032536

Note: The device is not suitable for use as a primary heat source.

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damage. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10032536

TECHNICAL DATA

PRODUCT DATA SHEET

only
Nominal heat output| Pnom| 2.0| kW| | manual heat charge control, with integrated thermostat| N/A
Minimum heat output| Pin| 1.0| kW| | manual heat charge control with room and/or outdoor temperature feedback| N/A
Maximum continuous heat output| Pmax,c| 2.0| kW| | electronic heat charge control with room and/or outdoor temperature feedback| N/A
Auxiliary electricity consumption| | fan assisted heat output| N/A
At nominal heat output| elmax| 2.0| kW| | Type of heat output/room temperature control
At minimum heat output| Elgin| 1.0| kW| | single-stage heat output and no room temperature control| no
In standby mode| USB| 0.48| W| | Two or more manual stages, no room temperature control| no
| | with mechanic thermostat room temperature control| no
| with electronic room temperature control| no
| electronic room temperature control plus day timer| no
| electronic room temperature control plus week timer| yes
| Other control options (multiple selections possible)
| room temperature control, with presence detection| no
| room temperature control, with open window detection| no
| with distance control option| no
| with adaptive start control| yes
| with working time limitation| no
| with black bulb sensor| no
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany

SAFETY INSTRUCTIONS

• Do not use the appliance until it is securely fixed as described in this manual.
• Check that the voltage indicates on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.
• If the supply cord is damaged, it must be replaced by a qualified engineer in order to avoid a hazard.
• The fireplace heater must not be positioned directly under the power socket.
• Keep furniture, curtains, and other flammable material at least 1 meter away from the appliance.
• Do not leave the appliance unattended during use.
• Do not leave the appliance unattended whilst connected to the main supply.
• Keep out of reach of children and do not allow them to operate this appliance.
• This appliance is intended for household use only and should not be used for industrial purposes.
•  Do not operate this appliance after a malfunction or after being dropped or damaged in any way.
• Repairs to electrical appliances should only be performed by a qualified electrician.
• Improper repairs may place users at serious risk.
• Do not run the mains cable under carpets, rugs, etc.
• Do not allow the main cable to hang over sharp edges or come in contact with hot surfaces.
• In order to avoid overheating, do not cover the heater.
• Do not use this heater with a programmer, timer, separate remote control system, or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
• Never immerse the product in water or any other liquid for any reason.
• Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
• Do not use the appliance outdoors.
• Do not use it if you have wet hands.
• Never use the appliance on or near hot surfaces.
• Do not operate with a damaged cord.
• Before cleaning the appliance, make sure it is unplugged from the power and that it is completely cooled.
• Do not clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not lift the appliance by the front panel.
• Keep the top of the heater at least 1000mm away from the ceiling or other objects for optimum heat ventilation.
• This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3  years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION
Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

BEFORE FIRST USE

Please retain all packaging until you have checked and counted all the parts and the contents of the fixing pack against the parts list. The fixing pack contains small items,  which should be kept away from young children. We suggest that you open the fixing pack and place all the contents into a container, therefore reducing the risk of losing any small pieces.

MOUNTING

Wall mounting

•  Do not connect the appliance to the mains until properly fixed to the wall and the instructions are read fully.
• The minimum distances must be observed in the diagrams on the right.
• For installation of the appliance, care must be taken not to damage concealed cables.
• Please be careful whilst drilling holes.
• This appliance is designed to be permanently fixed to a wall at a minimum height of 300 mm. The wall bracket must be fitted horizontally and the cable routed to the bottom right of the heater.

|
---|---
Figure 1: A distance of 600mm from the bottom of the heater to the floor is recommended for optimum viewing of the fuel bed; see Fig.1 for recommend fixing dimensions.| Figure 2 : For optimum viewing, mark the top five screws fixing positions  on the wall in accordance with the recommend fixing dimensions

Ensure that the bracket is level by using a Spirit level whilst marking out the hole positions. Drill holes with a No. six drill bit. Fix the wall bracket using the plug and screws provided. Attach the lower fixing bracket to the base of the fire using the two small black screws supplied; ensure the bracket is fitted so that it is level with the back. Carefully lift the heater up ensuring that the top rear ledge of the heater engages with the wall bracket (see Fig.2 in a circle) and is sitting centrally. This process should be carried out by two people to avoid injury or damage to property or the appliance. Gently bring the heater down against the wall.

|
---|---
Figure 3: Mark the lower fixing bracket two fixing hole positions on the wall- see
Fig.3, remove the heater. Drill the wall and insert the wall plugs. Refit the heater to the wall and fasten the bottom fixing bracket to the wall using the screws provided to permanently fix the heater in place.| Figure 4: Place the front surround over the front of the fire aligning the slots in the brackets at each side of the front panel with the lugs on the sides of the fire-see Fig.4. Again two people will be required
for this operation.

Mounting the Fireplace Stand
It is possible to install the electric fireplace on a surface, instead of mounting it on the wall.

• Remove the tempered glass from the metal body.
• Place the metal body horizontally on a table.
• In the lower part of the body there are some holes; align them to the holes on the fireplace stand.
• Use the supplied screws to secure the base to the lower side of the main body.
• Place the unit on a flat and stable surface.
• With some help, install the tempered glass.
• Align the lateral hooks of the glass with the notches on the sides of the metal body.

GENERAL USE

Note: The appliance can be operated either by the switches located on the top right-hand side of the fire or by the supplied remote control.
Manual Operation

• This is done by operating the switches located at the top right-hand side of the fire. The standby rocker switch must first be switched on, the fire will beep to indicate that it is powered up.
• Press the O/I button once to turn on the appliance and fire effect. A red indicator light will show to indicate that the fire is ON. Press the O/I button for 3 seconds this will operate the dimmer mode, hold the button down until the desired brightness is obtained.
• Press the POWER button once for the low heat setting 1000W; press twice for the high heat setting 2000W; press three to switch off the heat setting.
• Press the BACKLIGHT button to adjust the colors of LED decoration, 7 colors are available.

Remote Operation
The standby rocker switch located at the top right-hand side of the fire must first be switched on; the fire will beep to indicate that it is powered up. It takes a little time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for the fire to operate normally

DISPLAY AND INDICATORS

1 Cursor
2 Date
3 Timer
4 Standby
5 Temperature display/
serial number display| 6 Timer off
7 Timer on
8 Time display
9 Automatic control of heating
10 Flame brightness
11 Heat position
---|---

Temperature and serial number display (5)
Normally it displays the room temperature; while setting the temperature, the setting temperature is displayed; When setting the timer, the serial number of the setting is displayed.
Time display (8)
Normally it displays the current time; while setting the timer, the setting time is displayed.

Timer starting and timer shutdown
While setting the timer, the setting time is displayed, and the timer is used in combination with the serial number setting.

|

E.g. Means the starting time of setting 5 is 23:40.

---|---
|

E.g. means the shutdown time of setting 5 is 6:10.

Flame brightness
It displays the current brightness of the flame, which ranges from one to five positions.

OPERATION AND SETTINGS

Boot steps

1.  Connect the power.
2. Turn on the power switch.
3. Press the control switch or „ON/OFF“ key of the remote controller to start up
4. Press the 1000W/2000W button once for the low heat setting 1000W; press twice for the high heat setting 2000W; press three to switch off the heat setting.
5. Press the DIMMER button to operate the dimmer mode, repeat pressing will raise and lower the brightness.
6.  Press the BACKLIGHT button to adjust the colors of LED decoration, 7 colors are available.

Adaptive start control function
Press „IC“ button on the remote controller to start or close the adaptive start control function. When turned on this function, the fireplace can automatically change the heating mode, and this depends on the set temperature and the room temperature. When the timer is on, it is possible to start the heating ahead of the schedule.
Note: Adaptive start control function is only working when the week timer system is powered on.

The date and time setting
1 Press the „DATE-TIME“ button, then press the „▲ “ or „ ▲“ key to select the day.
2 Press „DATE-TIME“ button again, then press the „+“ or „-“ to set the hour
3 Press „DATE-TIME“ button again, then press the „+“ or „-“ to set the minute
4 Press the „OK“ button to finish the setting.
Temperature setting

The default temperature setting is 22°C, press „+“ or „-“ on the remote controller to set the temperature, which ranges is from 15°C to 30°C.

TIMER SETTINGS

• There are up to 10 kinds of timer settings.
• Each setting has its date, power-on time, shutdown time, and temperature setting
• The max. time of each setting is 23 hours 50 minutes
•  The set date for each timer can be any day or more days of a week
• The set date is the date of power-on time. If the shutdown time is on the second day, it is unnecessary to set the date, you just set the shutdown time.

View the timer setting

1. Press the „TIMER SET“ button
2.  Press the „+“ or „-“ to check the power-on time one by one.
3.  For checking the shutdown time, press the „ ▲“ button
4.  Press the „+“ or „-“ to continue viewing
5. For deleting the current item of setting, press „C“ to delete this setting.

Timer setting
(1) Select the settings
Press the „TIMER SET“ button, and the serial number of the setting starts blinking Press the „+“ or „-“ to change the serial number of the setting. E.g., it is showing the setting of No.2.

(2) Select the date
Press the „TIMER SET“ button once again, and the cursor on the left side of the date starts blinking Press the „ “ or “ ” keys to move the cursor to the corresponding date and press the „▲+▼“ to add the corresponding date or press „-“ to delete the date until you have completed the selection of all dates
(3) Set the start time

1.  Continue to press the „TIMER SET“ button, the hour starts blinking
2. Press the „+“ or „-“ to adjust the hour
3. Continue to press the „TIMER SET“ button, the minute starts blinking
4. Press the „+“ or „-“ to adjust the minute

(4) Set the shutdown time

1.  Press the „TIMER SET“ button, the display is off, and the hour starts blinking.
2.  Press the „+“ or „-“ to adjust the hour.
3. Continue to press the „TIMER SET“ button, and the minute starts blinking.
4. Press the „+“ or „-“ to adjust minute.

(5) Set temperature
Then press the „TIMER SET“ button, and the temperature setting starts blinking. Then you can adjust the temperature by pressing the „+“ or „-“. and the “+” button will raise the temperature, and the “-” will lower the temperature.

Press the „TIMER SET“ button to continue setting, and press „OK“ complete the setting.
Important Notes on Timer

• TIMER ON/OFF is to control the timer opening and closing
• Note 1: Restart the machine after the power is cut off, the original setting is kept, but the date and time must be reset.
• Note 2: When the week timer is powered on, you should turn on the heating function, or else when the machine is working again as the timer, there will be only the flame effect working.

Safety Cut-Off
This appliance is fitted with a safety cut-off which will operate if the fire overheats (e.g. due to blocked air vents). For safety reasons, the fire will NOT automatically reset. To reset the appliance, disconnect the appliance from the main supply for at least 15 minutes. Reconnect to the main supply and switch on the appliance.

Troubleshooting

Check for safety cut-off operation.
No fire effect light.| Check the bulb by a qualified electrician.

CARE AND CLEANING

Always disconnect from the mains supply before cleaning the heater. For general cleaning use a soft clean duster – never use harsh abrasives or cleaners.
Note: The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners.
This product does not use a standard bulb for its flame effect. The appliance uses an electronically controlled LED system to create the effect, therefore no parts need to be replaced. There are no user-serviceable parts on this appliance. Under no circumstances should the appliance be serviced by anyone other than a qualified electrician.

DISPOSAL CONSIDERATIONS

****If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.
This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom       

www.klarstein.com

References

• Klarstein | Your home. Your kitchen. Your style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>