Laird BL653U Bluetooth 5.1 Nano BLE Data Module User Manual
- May 15, 2024
- Laird
Table of Contents
- Laird BL653U Bluetooth 5.1 Nano BLE Data Module User Manual
- CURRENT REGULATORY CERTIFICATIONS
- CERTIFIED ANTENNAS
- FCC R EGULATORY
- Antenna Information
- FCC Documentation Requirements
- FCC Radiation Exposure Statement:
- IMPORTANT NOTE
- End Product Labeling
- Manual Information to the End User
- Antenna Information
- ISED Canada Statement
- Radiation Exposure Statement:
- IMPORTANT NOTE:
- Manual Information to the End User
- ISED ICES-003 Issue 7 Compliance Declaration
- AUSTRALIA AND NEW ZEALAND REGULATORY
- Safety
- Radio Equipment
- CE R EGULATORY
- User’s Guide Requirements
- EN 62368-1:2014/A11:2017
- EN 50665:2017 | EN 50385:2017
- EN 301 489-17 V3.2.0 (2017-03)
- § EU 2015/863 (RoHS 3)
- EU Declarations of Conformity
- safety
- systems
- Antenna Information
- REGULATORY DOMAIN SUPPORT
- R EVISION H ISTORY
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Laird BL653U Bluetooth 5.1 Nano BLE Data Module User Manual
CURRENT REGULATORY CERTIFICATIONS
The BL653µ (453-00059 and 453-00060) holds current certifications in the following countries:
Country/Region | Regulatory ID |
---|---|
USA (FCC) | SQGBL653U |
EU | N/A |
Canada (ISED) | 3147A-BL653U |
UK (UKCA) | N/A |
Japan (MIC) | 201-200419 |
Australia | N/A |
New Zealand | N/A |
CERTIFIED ANTENNAS
The antennas listed below were tested for use with the BL653µ. For CE mark
countries, the OEM is free to use any manufacturer’s antenna and type of
antenna if the gain is less than or equal to the highest gain approved for
use. Contact a Laird Connectivity representative for more information
regarding adding antennas.*
*Note: Japan (MIC) lists applicable antennas on its certificates, so if
your antenna is not on the approved list, irrespective of whether it is
comparative, it must be added to the certificate before it can be used in
Japan.
| | | | |
---|---|---|---|---|---
| |
Laird Connectivity Part Number
| | | Peak Gain
Manufacturer| Model| Type| Connector| 2400-2500
MHz
| 2400-2480
MHz
Laird Connectivity| NanoBlue| EBL2400A1-
10MH4L
| PCB
Dipole
| IPEX MHF4| 2 dBi| –
Laird Connectivity| FlexPIFA| 001-0022| PIFA| IPEX MHF4| –| 2 dBi
Mag.Layers| EDA-8709-2G4C1-B27-CY| 0600-00057| Dipole| IPEX MHF4| 2 dBi| –
Laird Connectivity| mFlexPIFA| EFA2400A3S-
10MH4L
| PIFA| IPEX MHF4| –| 2 dBI
Laird Connectivity| Laird Connectivity NFC| 0600-00061| NFC| N/A| –| –
Yageo| ANT1608LL14R2400A| NA| Chip| N/A| 2 dBi| 2 dBi
Laird Connectivity| i-FlexPIFA| EFG2400A3S| Flexible PIFA| MHF1/ MHF4| 3.1|
Note: **** The BL653µ module internal Bluetooth LE chipset IC pins are rated 4 kV (ESD HBM). ESD can find its way through the external header connectors like JTAG connector (if used on the customer’s design), if discharge is applied directly. Customer should ensure adequate protection against ESD on their end product design (using the BL653µ module) to meet relevant ESD standard (for CE, this is EN301-489).
FCC R EGULATORY
The 453-00059 and the 453-00060 hold full modular approvals. The OEM must follow the regulatory guidelines and warnings listed below to inherit the modular approval.
Part # | Form Factor | Tx Outputs | Antenna |
---|---|---|---|
453-00059 | Surface Mount | 8 dBm | Chip antenna |
453-00060 | Surface Mount | 8 dBm | IPEX MHF4 |
Antenna Information
The BL653µ has been designed to operate with the antennas listed below with a maximum gain of 3.1 dBi. The required antenna impedance is 50 ohms.
| |
Laird Connectivity Part Number
| | | Peak Gain
---|---|---|---|---|---
Manufacturer| Model| Type| Connector| 2400-2500
MHz
| 2400-2480
MHz
Laird Connectivity| NanoBlue| EBL2400A1-
10MH4L
| PCB
Dipole
| IPEX MHF4| 2 dBi| –
Laird Connectivity| FlexPIFA| 001-0022| PIFA| IPEX MHF4| –| 2 dBi
Mag.Layers| EDA-8709-2G4C1-B27-CY| 0600-00057| Dipole| IPEX MHF4| 2 dBi| –
Laird Connectivity| mFlexPIFA| EFA2400A3S-
10MH4L
| PIFA| IPEX MHF4| –| 2 dBI
Laird Connectivity| Laird Connectivity NFC| 0600-00061| NFC| N/A| –| –
Yageo| ANT1608LL14R2400A| NA| Chip| N/A| 2 dBi| 2 dBi
Laird Connectivity| i-FlexPIFA| EFG2400A3S| Flexible
PIFA
| MHF1/
MHF4
| 3.1|
FCC Documentation Requirements
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving
- Increase the separation between the equipment and
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced radio/TV technician for
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population/ uncontrolled exposure.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference; and
- This device must accept any interference received, including interference that may cause undesired
FCC Radiation Exposure Statement:
The product complies with the US portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This device is intended only for OEM integrators
under the following condition:
- The transmitter module may not be co-located with any other transmitter or antenna,
If the condition above is met, further transmitter testing is not required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
IMPORTANT NOTE
If this condition cannot be met (for example, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator is responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following:
“Contains FCC ID: SQGBL653U”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
ISED (C ANADA ) R EGULATORY
Part # | ID |
---|
453-00059
453-00060
| 3147A-BL653U
Antenna Information
This radio transmitter (IC: 3147A-BL653U) was approved by Innovation, Science and Economic Development (ISED) Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
| |
Laird Connectivity Part Number
| | | Peak Gain
---|---|---|---|---|---
Manufacturer| Model| Type| Connector| 2400-2500
MHz
| 2400-2480
MHz
Laird Connectivity| NanoBlue| EBL2400A1-
10MH4L
| PCB
Dipole
| IPEX MHF4| 2 dBi| –
Laird Connectivity| FlexPIFA| 001-0022| PIFA| IPEX MHF4| –| 2 dBi
Mag.Layers| EDA-8709-2G4C1-B27-CY| 0600-00057| Dipole| IPEX MHF4| 2 dBi| –
Laird Connectivity| mFlexPIFA| EFA2400A3S-
10MH4L
| PIFA| IPEX MHF4| –| 2 dBI
Laird Connectivity| Laird Connectivity NFC| 0600-00061| NFC| N/A| –| –
Yageo| ANT1608LL14R2400A| NA| Chip| N/A| 2 dBi| 2 dBi
Laird Connectivity| i-FlexPIFA| EFG2400A3S| Flexible
PIFA
| MHF1/
MHF4
| 3.1|
ISED Canada Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the
Radiation Exposure Statement:
The product complies with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The minimum separation distance for portable use is limited to 15mm assuming use of antenna with 2dBi of gain. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 3147A-BL653U”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
ISED ICES-003 Issue 7 Compliance Declaration
This device was originally tested to the requirements of ICES-003 Issue 6, Information Technology Equipment (Including Digital Apparatus) — Limits and Methods of Measurement; and evaluated to the updates published in ICES-003, Issue 7, Information Technology Equipment (Including Digital Apparatus). Based on this evaluation, this product continues to observe compliance to the requirements set forth by The Innovation, Science and Economic Development Canada (ISED), and complies with the updates published in ICES-003, Issue 7, Information Technology Equipment (Including Digital Apparatus).
J APAN (MIC) R EGULATORY
The BL653µ is approved for use in the Japanese market. The part numbers listed
below hold WW type certification. Refer to
ARIB-STD-T66 for further guidance on OEM’s responsibilities.
Model | Certificate Number | Antenna |
---|---|---|
453-00059 | 201-200419 | Chip Antenna |
453-00060 | 201-200419 | Trace pin |
AUSTRALIA AND NEW ZEALAND REGULATORY
RCM: Pending Compliant to standards EN 300 328 V1.9.1, AS/NZS 4268:
2012-A1:2013, and EN 55022:2010/AC:2011
If this device is used in a product, the OEM has responsibility to verify
compliance of the final end product to the Australia/New Zealand (RCM)
Standards. All end-products require their own certification (SDoc). You will
not be able to leverage the module certification and ship product into the
country.
UK (UKCA)
Manufacturer | Laird Connectivity |
---|---|
Products | 453-00059, 453-00060 |
Product Description | Bluetooth v5.x + 802.15.4 + NFC |
UK Legislation
| Radio Equipment Regulations 2017
Electromagnetic Compatibility Regulations 2016 Electrical Equipment (Safety) Regulations 2016
Reference standards used for conformity:
Legislation | Requirement | Reference standard(s) |
---|
Safety
Low voltage equipment safety EN 62368-1: 2014
EN 50663:2017
RF Exposure
EMC Protection
requirements – Electromagnetic compatibility
EN 62479: 2010
EN 301 489-1 v2.2.3 (2019-11)
EN 301 489-3 v2.1.1 (2019-03)
EN 301 489-17 v3.2.4 (2020-09)
EN 300 328 v2.2.2 (2019-07) Means of the efficient use of the
Radio Equipment
Means of the efficient use of the radio frequency spectrum (ERM)
radio frequency spectrum (ERM) EN 300 330 v2.1.1 (2017-02) Short Range
Devices (SRD)
Declaration:
We, Laird Connectivity, declare under our sole responsibility that the
essential test suites have been carried out and that the above product to
which this declaration relates is in conformity with all the applicable
requirements outlined above, when used for its intended purpose.
The minimum distance between the user and/or any bystander and the radiating
structure of the transmitter is 20 cm.
Place of Issue:| Laird Connectivity
W66N220 Commerce Court, Cedarburg, WI 53012 USA tel: +1-262-375-4400 fax: +1-262-364-2649
---|---
Date of Issue:| September 9, 2021
Name of Authorized Person:| Brian Petted, Technology Leader
Signature of Authorized Person:|
CE R EGULATORY
The 453-00059/453-00060 have been tested for compliance with relevant
standards for the EU market. The 453-00060 module was tested with a 2 dBi
antenna. The OEM can operate the 453-00041 module with any other type of
antenna but must ensure that the gain does not exceed 2 dBi to maintain the
Laird approval.
The OEM should consult with a qualified test house before entering their
device into an EU member country to make sure all regulatory requirements have
been met for their complete device.
User’s Guide Requirements
The integrator must include specific information in the user’s guide for the
device into which the BL653µ is integrated. In addition to the required FCC
and IC statements outlined above, the following Radio Equipment Directive
(RED) statements
must be added in their entirety and without modification into a prominent
place in the user’s guide for the device into which the BL653µ is integrated:
This device complies with the essential requirements of the 2014/53/EU – Radio
Equipment Directive (RED). The following test methods have been applied in
order to prove presumption of conformity with the essential requirements of
the 2014/53/EU – Radio Equipment Directive (RED):
EN 62368-1:2014/A11:2017
Safety requirements for audio/video, information, and technology equipment
EN 300 328 v2.2.2 (2019-07)
Electromagnetic compatibility and Radio Spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
EN 50665:2017 | EN 50385:2017
RF exposure
EN 301 489-1 v2.2.0 (2017-03)
Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements
EN 301 489-17 V3.2.0 (2017-03)
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
§ EU 2015/863 (RoHS 3)
Declaration of Compliance – EU Directive 2015/863; Reduction of Hazardous
Substances (RoHS)
This device is a 2.4 GHz wideband transmission system (transceiver), intended
for use in all EU member states and EFTA countries, except in France and Italy
where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum
authorities in order to obtain authorization to use the device for setting up
outdoor radio links and/or for supplying public access to telecommunications
and/or network services.
This device may not be used for setting up outdoor radio links in France and
in some areas the RF output power may be limited to 10 mW EIRP in the
frequency range of 2454 – 2483.5 MHz. For detailed information the end-user
should contact the national spectrum authority in France.
EU Declarations of Conformity
Manufacturer | Laird Connectivity |
---|---|
Products | 453-00059, 453-00060 |
Product Description | Bluetooth v5.x + 802.15.4 + NFC |
EU Directives | 2014/53/EU – Radio Equipment Directive (RED) |
Reference standards used for presumption of conformity:
Low voltage equipment
EN 62368-1: 20143.1a
safety
EN 50663:2017 EN 62479: 201
Means of the efficient use of the radio frequency spectrum (ERM)
EN 300 328 v2.2.2 (2019-07) Wide-band transmission
systems
EN 300 330 v2.1.1 (2017-02) Short Range Devices (SRD
Declaration:
We, Laird Connectivity, declare under our sole responsibility that the
essential radio test suites have been carried out and that the above product
to which this declaration relates is in conformity with all the applicable
essential requirements of Article 3 of the EU Radio Equipment Directive
2014/53/EU, when used for its intended purpose.
The minimum distance between the user and/or any bystander and the radiating
structure of the transmitter is 20 cm.
Place of Issue:| Laird Connectivity
W66N220 Commerce Court, Cedarburg, WI 53012 USA tel: +1-262-375-4400 fax: +1-262-364-2649
---|---
Date of Issue:| November 10, 2020
Name of Authorized Person:| Ryan Urness
Signature of Authorized Person:|
Antenna Information
The antennas listed below were tested for use with the BL653µ. For CE mark
countries, the OEM is free to use any
manufacturer’s antenna and type of antenna if the gain is less than or equal
to the highest gain approved for use (2dBi) Contact a Laird Connectivity
representative for more information regarding adding antennas.
Laird Connectivity Part Number | Peak Gain | ||||
---|---|---|---|---|---|
Manufacturer | Model | Type | Connector | ||
2400-2500 MHz | 2400-2480 MHz |
Laird
Connectivity
| NanoBlue| EBL2400A1-10MH4L| PCB Dipole| IPEX MHF4| 2 dBi| –
Laird
Connectivity
| FlexPIFA| 001-0022| PIFA| IPEX MHF4| –| 2 dBi
Mag.Layers| EDA-8709-2G4C1-B27-CY| 0600-00057| Dipole| IPEX MHF4| 2 dBi| –
Laird
Connectivity
| mFlexPIFA| EFA2400A3S-10MH4L| PIFA| IPEX MHF4| –| 2 dBI
Laird
Connectivity
| Laird Connectivity NFC| 0600-00061| NFC| N/A| –| –
Yageo| ANT1608LL14R2400A| NA| Chip| N/A| 2 dBi| 2 dBi
Note: The BL653µ module internal Bluetooth LE chipset IC pins are rated 4 kV (ESD HBM). ESD can find its way through the external header connectors like JTAG connector (if used on the customer’s design), if discharge is applied directly. Customer should ensure adequate protection against ESD on their end product design (using the BL653µ module) to meet relevant ESD standard (for CE, this is EN301-489).
REGULATORY DOMAIN SUPPORT
Domain support but not currently certified for – TBD
R EVISION H ISTORY
Version | Date | Notes | Contributor(s) | Approver |
---|---|---|---|---|
1.0 | 19 Jan 2021 | Initial version | Maggie Teng | Jonathan Kaye |
1.1 | 20 May 2021 | Added ISED ICES-003 Issue 7 compliance declaration | Sue | |
White | Ryan Urness | |||
1.2 | 09 Sept 2021 | Added UKCA DoC | Sue White | Brian Petted |
1.3 | 11 Feb 2022 | Updated UKCA standards | Sue White | Dave Drogowski |
1.4 | 8 Dec 2023 | Added EFG2400A3S to supported antennas for FCC / ISED | Dave | |
Drogowski | Brian Petted |
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>