Haltian Thingsee Presence Wireless Miniature Infrared IoT Sensor Installation Guide

Thingsee Presence Wireless Miniature Infrared IoT Sensor
Installation Guide

Welcome to using Thingsee
Congratulations on choosing Haltian Thingsee as your IoT solution.
We at Haltian want to make IoT easy and accessible for everyone, so we have created a solution platform that is easy to use, scalable and secure. I hope our solution will help  you achieve your business goals!

Thingsee PRESENCE

Wireless sensor for measuring people presence through your facility.
Thingsee PRESENCE gives you information on people movement in your spaces. You can use the sensor for facility management, workspace occupancy and visitor count. The sensor uses a passive infrared sensor to detect movement in a specific area.

Sales package content

• Thingsee PRESENCE sensor
• 1 x Opening Key

Using Thingsee PRESENCE sensor

Sensor detects the movement based on body heat detection.

Using sensor for visitor counting
Sensor can be used for visitor counting in places like door ways and corridors. Thingsee Visitor Counter Dome is available for this purpose.

Using workspace occupancy detection

Thingsee PRESENCE can be installed under a table to detect the usage of a working space. Sensor sensitivity should be decreased to avoid unwanted detections outside the  working space. This is possible with Thingsee Occupancy Dome.

General installation instructions

Sensor is for indoor use only.
The sensor is more sensitive to movement across the sensor detecting area than towards the sensor.

The sensor can only measure movement inside the detecting area.
It is not a volumetric sensor.

When attaching to a wall, place the sensor around 2/3rds of the wall height to avoid unnecessary detection of pets or other domestic animals. Sensor sensitivity can be also  reduced in such cases. 

In a large area, use multiple sensors to cover all required movement.

Sensors can also be placed either to a wall or to a ceiling.

If sensors are placed on a ceiling in a low height space, sensors should be placed close enough to each other to cover the entire detecting area.

Thingsee PRESENCE detection capability changes related to the height of the space. Following chart describes different distances.
Adjusted sensitivity levels shown as white lines inside the maximum area are for illustration purposes only. Detection area changes related to sensor sensitivity level. Thingsee  PRESENCE detects people movement in its detection area with maximum of 34 movements per minute despite the movement’s direction or distance from the sensor.

Things to avoid in installation

Avoid installing Thingsee products near the following:
Nearby heating or cooling devices and/or vents.

Direct sun light.

Nearby halogen lamps or similar lamps with hot surface.

Places where a door or a similar object can block the required detection area.

Attachment to surfaces which can vibrate as it may cause false functionality.

Changing the batteries

Open the sensor to change the batteries or reboot the device by replacing the batteries.

Installation

Please make sure the Thingsee gateway device is installed before you install the sensors.
To identify the sensor, read the QR code on the front of the device with a QR code reader or Thingsee installation application on your mobile device.
Identifying the device is not necessary, but it will help you keep track of your IoT installation and help Haltian support to solve possible issues.

Carefully pull out the battery security tab.
LED indicator (red) will flash once. If the LED doesn’t flash within 2 minutes, tap the sensor against your palm. If you do not see the LED blink or see the events from the  sensor within 5 minutes, re-install the batteries.

Clean the surface you will attach the sensor to with IPA -solvent (isopropyl alcohol).
Remove the tape’s paper cover from the backside of the sensor.

Attach the sensor to its place by pushing it firmly against the surface for a minimum of 5 seconds. Wipe the sensor with a dry, clean cloth.

Visitor counting

Installing the sensor to a ceiling
Place the sensor in the middle of the door opening, 5 to 10 cm from the wall. Make sure that there are no objects between the sensor and the area to be detected.

Installing the sensor to a door opening
Install Thingsee PRESENCE sensor to the top middle of the door opening. Make sure that there are no objects between the sensor and the area to be detected.

Movement direction
The sensor should be installed related to the visitor movement direction as shown in the image.

Using Visitor Counter Dome
The detection beam can easily be adjusted with a separate, easy to install, Visitor Counter Dome.
It makes the detection beam more accurate.

Note that with the Dome, the detection area is narrowed related to the long side of the Thingsee PRESENCE sensor.

Detection area shape

Detection area shape and dimension related to the most common installation distances.

Workplace occupancy detection

Thingsee PRESENCE can be installed under a table to detect the usage of a working space. Sensor sensitivity should be decreased to avoid unwanted detections outside the working space. Installing the sensor under a table

Install Thingsee PRESENCE under the table as middle as possible. If there are any objects, such as table legs, under the table, place the sensor on the user side of the object.  Make sure there is 50 mm gap between Thingsee PRESENSE and the object so that it can be easily maintained.

Using Workplace Occupancy Dome

The detection beam can easily be adjusted with a separate, easy to install, Workplace Occupancy Dome. The detection beam is more accurate when the hole on top of the  sensor is facing front.

Good to know about installing the Dome
The Dome can be attached with screws to ensure the installation.
Use a correct screw type!

When using the attachment clips only, the screw attachement parts can be cut off.
Do not damage attachment clips while cutting!

Device info

Operating temperature: -20 °C … +50 °C
Operating humidity: 0 % … 100 % RH non-condensing
Storage temperature: 0 °C … +25 °C
Storage humidity: 45 % … 60 % RH non-condensing
IP rating grade: IP40
Certifications: CE, FCC, ISED, RoHS, RCM and MIC compliant
Battery type: 2 x AAA, replaceable
Expected battery life:
Up to 5 years, with standard firmware
Radio sensitivity: -95 dBm (BTLE)
LED light for confirmation purposes
Adjustable sensor sensitivity

Device measurements

Default functionality and configuration
Reports an indicative count of detected movements every 1 minute
Max count per minute is 34 events
The device LED blinks (red) once when starting up
Radio connectivity: Wirepas Mesh
The following parameters are configurable remotely over Thingsee
Operations Cloud

• Reporting interval
• Sensor sensitivity level

Mesh network node role configuration

• Routing
• Non-routing

Movement indication LED ON/OFF
For further information, please refer to Haltian support pages at: https://support.haltian.com/

CERTIFICATION IN CERTIFICATION INFORMATION
EU DECLARATION OF CONFORMITY
Hereby, Haltian Oy declares that the radio equipment Thingsee PRESENCE is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is  available at the following internet address: www.haltian.com
Manufacturer name and address:
Haltian Oy
Yrttipellontie 1 D
90230 Oulu
Finland

FCC REQUIREMENTS FOR OPERATION IN THE UNITED STATES
FCC Information for the User
This product does not contain any user serviceable components and is to be used with approved, internal antennas only.
Any product changes of modifications will invalidate all applicable regulatory certifications and approvals.

FCC Guidelines for human Exposure

 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum  distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in  accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular  installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following methods:
Increase the separation between the equipment and the receiver.
Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected Consult the dealer or and experienced radio/TV technician  for help
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC compliance statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device  must accept any interference received, including interference that may cause undesired operation.

Innovation, Science and Economic Development Canada (ISED) regulatory information
This device complies with RSS-247 of the Innovation, Science and Economic Development Canada (ISED) Rules. Operation is subject to the following two conditions: (1) This  device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement :
This device complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and used with a minimum distance of 20 cm between the radiator and your body.

RCM-approved for Australia and New Zealand.
SAFETY GUIDE
Read these simple guidelines. Not following them may be dangerous or against local laws and regulations. For further information, read the user guide and visit www.haltian.com

Usage
Do not cover the device as it prevents the device from operating properly.

• This product is intended for indoor use only and shall not be exposed to rain.

• Do not modify the device. Unauthorized modifications may damage the device and violate regulations governing radio devices.

• Do not store the device in wet or humid conditions.

• Remove the batteries from the device if you are taking it inside an aeroplane (unless you have the pre-installed pull- out tape still in place). The device has a Bluetooth LE  receiver/transmitter which must not be operational during a flight.

• Please take care that the used batteries are recycled by taking them to appropriate collection point.

• When changing batteries, replace both of them at the same time using identical brand and type.

• Do not swallow batteries.

• Do not throw batteries into water or fire.

• Do not short-circuit batteries.

• Do not try to charge primary batteries.

• Do not open or disassemble batteries.

• Batteries should be stored in a dry place and at room temperature. Avoid large temperature changes and direct sunlight.
  At higher temperature the electrical performance of  the batteries may be reduced.

• Keep batteries away from children.

Care and maintenance
Handle your device with care. The following suggestions help you keep your device operational.

• Do not open the device other than as instructed in the user guide.
• Unauthorized modifications may damage the device and violate regulations governing radio devices.
• Do not drop, knock, or shake the device. Rough handling can break it.
• Only use a soft, clean, dry cloth to clean the surface of the device. Do not clean the device with solvents, toxic chemicals or strong detergents as they may damage your  device and void the warranty.
• Do not paint the device. Paint can prevent proper operation.

Damage
If the device is damaged contact support@haltian.com. Only qualified personnel may repair this device.
Small children
Your device is not a toy. It may contain small parts. Keep them out of the reach of small children.

RECYCLING
Check the local regulations for proper disposal of electronic products. The Directive on Waste Electrical and Electronic Equipment (WEEE), which entered into force as  European law on 13th February 2003, resulted in a major change in the treatment of electrical equipment at end-of-life. The purpose of this Directive is, as a first priority, the  prevention of WEEE, and in addition, to promote the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. The crossed-out wheelie-bin symbol  on your product, battery, literature, or packaging reminds you that all electrical and electronic products and batteries must be taken to separate collection at the end of their  working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste  authority. 

Get to know other Thingsee devices

For all devices and more information, visit our website www.haltian.com or contact sales@haltian.com

References

• Connected solutions for successful businesses | Haltian
• Technical information and FAQs | Haltian Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>