Haltian TSD2 Sensor device with wireless connection Instructions
- June 5, 2024
- Haltian
Table of Contents
Haltian TSD2 Sensor device with wireless connection
INTENDED USE OF TSD2
TSD2 is used for distance measurements and resulting data is sent wirelessly to a Wirepas protocol mesh network. The device has also an accelerometer. Typically TSD2 is used together with MTXH Thingsee Gateway in use cases where distance measurements are performed in several locations and this data is wirelessly collected and sent via 2G cellular connection to a data server/cloud.
GENERAL
Place two AAA batteries (recommended model Varta Industrial) inside the device, the correct direction is shown on the PWB. Plus sign indicates the positive node of the battery.
Snap the B cover in place (please note that the B cover can be placed only in
one direction). The device starts making distance measurements about any
objects on the top side of the device. Measurements are made once a minute
(default, can be changed by configuration).
The device starts seeking any other nearby devices having the same pre-
programmed Wirepas network ID as the device itself. If it finds any, it
connects to this Wirepas network and starts sending measurement results from
both sensors to the network once a minute (default, can be changed by
configuration).
INSTALLATION GUIDELINES
The device B cover has a double-sided tape which can be used for attachment; remove the cover tape and attach the device to the desired position for distance measurement. The surface for attachment needs to be flat and clean. Press the device from both sides for 5 seconds to make sure that the tape is correctly attached into the surface.
The device operates with fresh Varta Industrial batteries typically for more than 2 years (this time depends heavily on the configuration used for measurement and reporting intervals). If there is a need to change the batteries, spread the side of the A cover gently as shown in the picture below. Be careful while opening the cover that locking snaps don’t break. Remove the B cover, remove the batteries and place new batteries as described earlier.
If the device is already attached to some surface, opening needs to be performed with a special tool:
The tool can be ordered from Haltian Products Oy.
The device can also be ordered with batteries pre-installed. In this case just
pull out the tape disconnecting batteries in order to power on the device.
PRECAUTIONS
- TSD2 is intended for indoor use only and shall not be exposed to rain. The operating temperature range for the device is -20…+50 °C.
- Remove the batteries from the TSD2 device if you are taking it inside an aeroplane (unless you have the pre-installed pull-out tape still in place). The device has a Bluetooth LE receiver/transmitter which must not be operational during a flight.
- Please take care that the used batteries are recycled by taking them to appropriate collection point.
- When changing batteries, replace both of them at the same time using identical brand and type.
- Do not swallow batteries.
- Do not throw batteries into water or fire.
- Do not short-circuit batteries.
- Do not try to charge primary batteries.
- Do not open or disassemble batteries.
- Batteries should be stored in a dry place and at room temperature. Avoid large temperature changes and direct sunlight. At higher temperature the electrical performance of the batteries may be reduced.
- Keep batteries away from children.
LEGAL NOTICES
Hereby, Haltian Products Oy declares that the radio equipment type TSD2 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://thingsee.com
Haltian Products Oy vakuuttaa, etta radiolaitetyyppi TSD2 on direktiivin
2014/53/EU mukainen.
EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla
seuraavassa internetosoitteessa: https://thingsee.com
TSD2 operates at Bluetooth® 2.4 GHz frequency band. Maximum radio-frequency
power transmitted is +4.0 dBm.
Manufacturer name and address:
Haltian Products Oy
Yrttipellontie 1 D
90230 Oulu
Finland
FCC REQUIREMENTS FOR OPERATION IN THE UNITED STATES
FCC Information for the User
This product does not contain any user serviceable components and is to be
used with approved, internal antennas only. Any product changes of
modifications will invalidate all applicable regulatory certifications and
approvals.
FCC Guidelines for human Exposure
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 5 mm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Federal Communications Commission Statement
This device complies with Part 15 Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following methods:
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected
- Consult the dealer or and experienced radio/TV technician for help
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Industry Canada:
This device complies with RSS-247 of the Industry Canada Rules. Operation is
subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement :
This device complies with ISED radiation exposure limits set forth for an
uncontrolled environment.
- FCC ID: 2AEU3TSBEAM
- IC ID: 20236-TSBEAM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>