auna W2-Dark-Star-6000 Darkstar Channel Car Power Amplifier Instruction Manual

auna W2-Dark-Star-6000 Darkstar Channel Car Power Amplifier

Dear Customer,
Congratulations on purchasing this equipment. Please read this manual carefully and take care of the following hints on installation and use to avoid technical damages. Any failure caused by ignoring the items and cautions mentioned in the operation and installation instructions are not covered by our warranty and any liability.

Features

• 90W x 2 Channel/ 90W x 4 Channel/ 90W x 6 Channel
• Multi-mode connection capability for Simultaneous subwoofer & satellite speaker operation
• Adjustable subwoofer crossover frequency(3O—25OHz)
• High current discrete output devices
• Adjustable RCA level inputs
• Input ground isolation noise rejection circuit

Power Supply Section

• Ultra stable PWM (Pulse width modulated)
• Power supply (11~16V)
• Thermal Protection circuit
• Remote on power switching

General

• Transient noise muting
• Turn on delay
• Speaker short circuit protection
• Gold plate RCA input and terminals

Connection of Power Cord

• Since this unit deals with a high power, large current will flow and the wiring or power cord is high importance.

• Connect the red wire directly to the (+) terminal of the battery using the cord with a fuse holder supplied.

• Connect the black wire tightly to an appropriate screw on the metal part of car after removing paint
  for proper grounding. Be sure to use the screw not bring danger for driving.

• Proper connection will provide clear sound.

Connection of Remote On/Of Wire

• Connect the orange wire to a switched power cord of the car stereo to be connected to this unit will control the unit power on/off with the car stereo’ s
• The switched power cord may be obtained an auto antenna cord of the car stereo.

Connection of Booster Input (High Input)

• This unit can be connected to any car stereo with high-level outputs, common or separated ground outputs.
•  Separated ground car stereo connection;-connect car stereo speaker output cables to the high-level input connector (+) and (-), right and left polarity.
•  Common ground car stereo connection;-connect car stereo speakers negative output cable to the high-level input connector to the two signs (-) and the remaining cables to (+) right and left..

Connection of AUX Input (Low Input)

• Connect the AUX input wires with RCA type pin jack as follows: white to L Ch pre—output of the car stereo. Red to R Ch pre—output of the car stereo.
• Before connecting the pre—output of the car stereo or other unit, confirm the impedance or sensitiv-ity to match with this unit AUX input.

Input Sensitivity Control

• Adjust the input sensitivity to output of a car stereo connected.

Connection of Speaker (Stereo / Mono)
Connect the speaker wires as per the following figures 2-Channel

• 2-Channel
• 4-Channel
• 6-Channel

Note:

• Because of high power unit, approx 7,5A/ 15A/ 20A will be drained at peak power. Using the unit while the engine is stopped may totally discharge the battery. Please run the engine in using the unit.
• Because of large current flows, please use power supply cord of sufficient capacity if required. (Larg-er than 3mm square.)
• This unit is designed of use with the speaker’s 2~16Ω impedance. The speaker must have enough ca-pacity to accept the high power of the unit. Please carefully confirm the rating of the speaker before connection.

Wiring Operation for Stereo

• 2- Channel
• 4- Channel
• 6- Channel

Wiring Operation for Speakers

• 2- Channel
• 4- Channel
• 6- Channel

Mounting

Please mount at your option using screws and fixtures supplied with the units CAUTION::

• The unit itself will be heated because of its high power.
• Therefore, please leave room around the unit in mounting and while in use, and do not put things on the unit.

Specification

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed
of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>