Aipower AIW26H Wearbuds Watch User Manual

Airpower AIW26H Wearbuds Watch

Product Design

Watch charge

Before using the product for the first time, please charge the watch with a special charger.
(The input voltage of the device is standard USB 5.0V. Do not use any other power source to charge the device.)

Operating instructions

• Startup: long-press the side button three seconds when the device shutdown.
• Shutdown: Long press side button for three seconds when the device working

Download and install the application

Can search for Wearbuds and download them from the application market.

Connecting the watch with the app
Open the app, register, and log in to your Airpower account. Follow the on- screen instructions to connect the band with your device. Once connected, you can view fitness data and customize on-wrist notification settings in-app. Multiple personalized functions can be set through APP: push reminder, do not disturb mode, sleep setting. etc.

Earphone feature

Connect the phone

1. Take earphones out from the watch and wear in ears

Touch feature

Earphone notice

Take the earphones out of the charging case, will auto power on. Shutdown:
Put the earphones in the charging case, will auto-shutdown and charge.
It is connectionless, the earphone auto-shutdown time is about 300 seconds.

Phone paired:
You can’t get status but are connected when the phone is paired with one earphone.

1. You can enter pairing mode when you take the earbuds from the watch.
2. After about 300 seconds earphones shutdown if you keep the status

Connected

Your Bluetooth earphones auto-connect with your phone again if your phone was paired with your earphones success last time.
The earphones is paired with the phone’s success, Bluetooth earphone turn off phone Bluetooth turn off Bluetooth earphones turn on-phone Bluetooth turns on.
A. Both earphone away from the phone, the earphone is searched and reconnected with the phone if you are back in the 120s to the connectable range (Red and blue flash alternately) \

• iPhone can not search the device
  1. Phone-Setting-Bluetooth-My device- Select a paired watch from the pairing list: This device is ignored.
  2. Rebind
• Android phones cannot search for the watch, or cannot reconnect after the Bluetooth is disconnected.
  1. Please make sure “location information” is turned on in the system. (some of the android system phone search Bluetooth devices should turn on this feature)
  2. Unblind devise/blind it after turning on your Bluetooth Phone/Message/Notification function unusual
• iPhone: Please make sure the watch is paired with the phone, then turn off the notification, and turn it back on. Or restart your phone’s Bluetooth.
  Android: Open “earbuds”-Setting-About-Help; Check that the corresponding function is enabled.
  “Notice: Your watch couldn’t get a notification if your phone and your laptop open APP in the same time or your phone turn off notify the authority of APP.

Battery low
The red light keeps flashing slowly.

Notice

1. Charge: When the battery is too low, please timely charge can effectively protect the battery life.
2. To avoid overheating of the equipment and causing accidents, do not charge the device while it is in an environment above 50°c.
3. The device uses a built-in battery, to avoid damage to the device do not disassemble by yourself.
4. Do not make the device subjected to violent impact, puncture and extrusion to prevent damage and rupture of the battery; If the battery ruptured, please avoid contact with eyes and skin. Please do not rub the contact part if the battery contacts the skin, rinse immediately with water and send to the hospital
5. The measured data of this equipment are all reference data, do not use as a medical device.
6. Put the earphones in watch, will auto-shutdown and charge, take the earphones out of the watch, will auto power on.
7. The red light keeps on when charging and the light off when the earphone battery full.
8. To avoid charging unusually. please keep your earphones dear and dry before you put earphones on the watch.)

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end-user.

Earphone charge

Put your earphone (picture 1) on the side charge slot (picture 2). The red light indicates that the battery is charging, and the red light is off after it is full.
Note: To prevent the earphones from falling off, you can adjust the wearing direction of the watch and customize the watch screen display orientation by tapping’ setting’ as you like.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>