Aipower W26 Wearbuds Watch User Manual
- June 5, 2024
- Aipower
Table of Contents
W26 Wearbuds Watch
User Manual
Product Design Watch charge
Before using the product for the first time, please charge the watch with a
special charger.
(The input voltage of the device is standard USB 5.0V.Do not use any other
power source to charge the device.)
Earphone charge
Put your earphone (picture 1) on the side charge slot (picture 2). The red
light indicates that the battery is charging, and the red light is off after
it is full.
Note: To prevent the earphones from falling off. you can adjust the
wearing direction of the watch and customize the watch screen display
orientation by tapping’ setting’ as you like.
Operating instructions
Startup: long-press the side button for three seconds when the device
shutdown.
Shutdown: long-press the side button for three seconds when the device
working.
Download and install the applicatio n
Can search ‘Wearbuds’ and download them from the application market.
Connecting the watch with the app
Open the app, register, and log in to your Airpower account. Follow the on-
screen instructions to connect the band with your device. Once connected, you
can view fitness data and customize on-wrist notification settings in-app.
Multiple personalized functions can be set through APP: push reminder, do not
disturb mode, sleep setting, etc.
Earphone feature
Connect the phone
1. Take earphones out from the watch and wear them in your ears.
Open your phone Bluetooth and pair Bluetooth name ‘Wearbuds Watch-Buds’, the
earphone’s blue light will quickly flash three times after the earphones are
paired success.
Touch feature
Earphone notice
Take the earphones out of the charging case, will auto power on. Shutdown: Put
the earphones in the charging case, will auto-shutdown and charge. It is
connectionless, earphone auto-shutdown time is about 300 seconds Phone paired:
You can’t get status but are connected when the phone is paired with one
earphone.
- You can enter pairing mode when you take the earbuds from the watch.
- After about 300 seconds earphones shutdown if you keep the status
Connected
Your Bluetooth earphones auto-connect with your phone again if your phone was
paired with your earphones success last time. The earphones are paired with
the phone success, Bluetooth earphone turns off–phone Bluetooth turn
off–Bluetooth earphone turn on–phone Bluetooth turn on. A. Both earphone are
away from the phone, the earphone is searched and re-connected with the phone
if you are back in the 120s to the connectable range (Red and blue flash
alternately)
-
iPhone can not search the device
1. Phone–Setting—Bluetooth–My device– Select a paired watch from the pairing list: This device is ignored.
2. Rebind -
Android phones cannot search for the watch, or cannot reconnect after the Bluetooth is disconnected.
1. Please make sure “location information” is turned on in the system. (some android system phone search Bluetooth devices should turn on this feature)
2. Unblind the device/blind it after turning on your Bluetooth -
Phone/Message/Notification function unusual iPhone:
Please make sure the watch is paired with the phone, then turn off the notification, and turn it back on. Or restart your phone’s Bluetooth.
Android: Open “earbuds”–Setting–About–Help; Check that the corresponding function is enabled.
*Notice: Your watch couldn’t get notification if your phone and your laptop open the APP in the same time or if your phone turns off to notify the authority of the APP. Battery low
The red light keeps flashing slowly.
Notice
- Charge: When the battery is too low, please timely charge can effectively protect the battery life.
- To avoid overheating of the equipment and causing accidents, do not charge the device while it is in an environment above 50°c.
- The device uses a built-in battery, to avoid damaging the device, do not disassemble by yourself.
- Do not make the device subjected to violent impact, puncture, and extrusion to prevent damage and rupture of the battery; If the battery ruptured, please avoid contact with eyes and skin. Please do not rub the contact part if the battery contacts with the skin, rinse immediately with water, and send to the hospital.
- The measured data of this equipment are all reference data. do not use it as a medical device.
- Put the earphones in the watch, will auto-shutdown and charge. take the earphones out of the watch, will auto power on.
- The red light keeps on when charging and the light off when the earphone battery is full.
- To avoid charging unusually. please keep your earphones dear and dry before you put earphones on the watch.)
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received,
including interference that may cause undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.lf this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End-users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instructions as documented in this manual. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. The
availability of some specific channels and/or operational frequency bands are
country dependent and are firmware programmed at the factory to match the
intended destination. The firmware setting is not accessible by the end-user.
Watch Model: AI-W26
Earbuds Model: Al-W261-1
Watch FCC ID:2A61K-AIW26
Earbuds FCC ID:2A61K-AIW26H
Made in China
Manufacturer: Airpower Technology Co., Ltd
Address: 801-803. Building G4, Songshan
Lake International Innovation and Entrepreneurship Community, Dongguan City,
Guangdong Province, China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>