AiPOWER SUA6900D 6900 Watt Dual Fuel Portable Generator User Guide

AiPOWER SUA6900D 6900 Watt Dual Fuel Portable

Generator

Unpack Generator:

Remove generator, accessories, inserts and Literature from carton. If any item is missing or damaged, contact our product service department at 1-855-888-3598.

Included Items

WARNING: This Quick Reference Guide is not substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand the operator’s manual before using this product. All pages references to the operator’s manual.

Install the wheel kit

• Slide the axle pin(A) through the wheel(B), flat washer(C) and mount point on the frame(D). Secure them with cotter pin(E).
• Attach the support leg(G) to the generator frame with flange bolt(F)(M8X16) and flange lock nut(H)(M8).
• Install the handle(I) to the frame with bolts(J) (M8X20) . Add Lubricant and Fuel
• Use a funnel to pour provided engine oil into engine. Fill to the upper mark of the oil dipstick H.
• Use clean / fresh regular UNLEADED gasoline with a minimum 87 octane.

Adjust Shock-absorbing Seat

Before operating the generator the shock-absorbing seat (cushion) must be adjusted for proper clearance. Loosen the lock nut and adjust the shock- absorbing seat so there is a 3mm gap between the top of the seat and the bottom of the motor bracket. Re-tighten the lock nut. Danger: Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell.
NEVER use inside a home or garage, EVEN IF doors and windows are open.

Only use OUTSIDE and far away from windows, doors and vents.

Avoid other generator hazards. READ MANUAL BEFORE USE.

WARNING : Do not overload generator or electrical cords. Consult operation manual.

Start the Engine (Generator).

Select the Fuel Source (Gasoline)

1. Make certain the propane tank is fully closed. ****
2. Flip the fuel source switch on the side panel to the gasoline position.
3. Move the choke lever to the “START” position.
4. Pull the starter cord slowly until resistance is felt and then pull rapidly.
5. Move the choke lever to the “RUN” position.
6. Plug in items to be powered, using only grounded extension cords.

Select the Fuel Source (Propane/LPG)

1. Fully open the Propane/LPG cylinder knob.

2. Flip the fuel source switch on the side panel to the propane/LPG position.

3. Move the choke lever to the “START” position.

4. PULL-TO-PRIME
   Pull the starter cord 1-2 times to prime the engine.

5. Move the chock lever to the “RUN” position.

6. PULL-TO-RUN
   Pull the starter cord to start the engine.

7. Plug in items to be powered, using only grounded extension cords.

Shutdown and Storage

1. Turn off and remove entire electrical loads.
2. Flip the engine switch to “STOP” position.
3. Turn the propane/LPG cylinder knob to close position.

If generator is to be stored for longer than 30 days, refer to the operator’s manual for further instruction.

Changing Fuels

1. Disconnect all electrical loads from the generator.
2. Stop the engine (generator).

3a. Gasoline to propane/LPG

• Fully open the Propane/LPG cylinder knob.
• Flip the fuel source switch on the side panel to the propane/LPG position.

3b.Propane/LPG to Gasoline

• Make certain the propane tank is fully closed.
• Flip the fuel source switch on the side panel to the gasoline position.
• Start the engine (generator).

Questions? Call 1-855-888-3598 or email [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>