ADLER AD 2832 Cordless or Corded Hair Clipper User Manual
- June 3, 2024
- ADLER
Table of Contents
AD 2832 Cordless or Corded Hair Clipper
User Manual
SAFETY CONDITIONS
IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR
FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial
purposes.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 100-240V, ~50/60Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using it around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without supervision.
-
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.
-
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug, or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid
hazardous situations. -
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let the cord hang over the edge of a counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, and unplug the power.
-
In order to provide additional protection, it is recommended to install the residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.
-
**** If using the device in the bathroom after use remove the power plug from the socket, because water proximity presents a risk, even if the device is turned off.
-
Do not allow the device or power adaptor to wet. If the device falls into water, immediately remove the power plug or power adaptor from the socket. If the device is powered, do not put your hands in the water. Has the device been checked by a qualified electrician before using it again?
-
Do not touch the device or power adaptor with wet hands.
-
The device has to be turned off after every use.
-
Do not leave switched-on equipment or adapter without supervision.
-
Never use this device close to water, e.g.: Under a shower, in the bathtub, or above a sink filled with water.
-
If the device utilizes a power adaptor, do not cover it, because this can cause a dangerous temperature rise and can damage the device. Always connect the power adaptor cable to the device, and then connect the power adaptor to the power socket.
-
The cutting scissors are very sharp. Use caution when assembling, dismantling, and cleaning. Do not touch any elements of the moving blade during the operation!
-
Do not use the device for more than 10 minutes at a time. After 10 minutes have elapsed, turn it off for approximately 5 minutes. DO NOT CHARGE THE BATTERY FOR LONGER THAN 48 HOURS – this can cause irreversible damage to the battery.
-
The charging process should be conducted in temperatures between 5-35 degrees Celsius.
-
Do not wash the blades in the water.
-
Only change comb attachments when the device is switched off.
PRODUCT DESCRIPTION
(FIG. 1)
- On/off button
- Regulation of cutting length
- The scale of regulation of cutting length
- Charging indicator
- Charger
- Display
CHARGING THE BATTERY
Charge the battery before use. To begin charging plug the power cord into the trimmer’s socket, and the charger into a 100-240 V 50/60 Hz mains power outlet. The charging indicator will light up (fig. 1.4). The light will remain on until the device is unplugged from mains power. The first charge takes 8 hours; subsequent ones should last 4 hours. A fully-charged battery lasts for approximately 180 minutes of continuous use. After charging, unplug the charger from the socket. If the trimmer is not used for a long period of time, it should be charged at least once every 6 months. In order to maintain adequate battery capacity. If the battery is flat, you can continue cutting using the charger. To do this plug the charger cable into the trimmer socket. After 2 minutes you can continue cutting.
USING THE TRIMMER
Select the desired cutting length by turning the cutting length adjustment
knob (fig. 1.2), and observing the regulation scale (fig. 1.3).
To change the comb turn the trimmer off, unclip the comb (fig. 5) and clip on
the right one (fig. 4).
Start cutting by running the trimmer with the comb attachment against the
direction of hair growth. This should be done slowly and at a steady speed.
Please remember to regularly clean the trimmer and cut the head of any hair.
CLEANING
Unplug the device from the power source. Remove the cutting head (fig. 2). Clean the blade with the included brush. No hair should remain between the blades after cleaning. Every few haircuts lubricate the cutting head by dropping 2-3 drops of the machine oil into the space shown in fig. 6. Close the head (fig. 3). Clean the casing with a dry or slightly damp cloth.
Display information:
The display will show 4 pieces of information. 1. THe % state of the battery when it reaches 0 the device will turn off. 2. Turbo option the device will work on higher RPM. 3. Loading (The icon will be red) the % load of the battery will increase until 100% and then will turn green and start flashing. 4: and working under adaptor power (It will turn green) and not using a battery.
TECHNICAL INFORMATION
Power: 3 W Max Power: 40W
Power supply: 100-240 V ~50/60 H
The device is made in class II insulation.
The device is compliant with EU directives:
Low voltage directive (LVD)
Electromagnetic compatibility (EMC)
The device marked CE mark on the rating label
To protect your environment: please separate carton boxes and plastic bags and
dispose of them in corresponding waste bins. The used appliance should be
delivered to the dedicated collecting points due to hazardous components,
which may affect the environment. Do not dispose of this appliance in the
common waste bin.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>