Maxxima MCL-3324900B 32-Inch 3 CCT Selectable Oval LED Ceiling Mount Installation Guide

: June 4, 2024
: Maxxima

Table of Contents

INSTALLATION INSTRUCTIONS
CCT Color Selection
3 YEAR WARRANTY
Documents / Resources

MCL-3324900B
www.maxximastyle.com

WARNINGS

Risk of electric shock – Disconnect power at the source before installation.
If you are unsure about the installation or the maintenance of the wall light, please consult an electrician.
Do not make or alter any holes in the wiring enclosure or modify any electrical componentry.

CAUTIONS

To ensure personal safety, proper grounding of the electrical fixture is required.
The fixture must be wired in accordance with the National Electric Code and applicable local codes or ordinance
Min 90 ℃ Supply Conductors Les Fils D’alimentation 90 ℃ Min
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

INSTALLATION INSTRUCTIONS

Tools Needed: Screwdriver, drill, wire nuts, electrical tape. If you are replacing an existing fixture, remove and disconnect the old fixture first.

Place the canopy against the ceiling in the desired orientation and mark the locations of the mounting keyhole slots.
If necessary, drill holes for drywall anchors in the marked locations and install the anchors.
Install the supplied mounting screws. Leave approximately 1/4 inch of screw length exposed in order to mount the canopy.
Expose the power supply wires from the junction box.
Connect the green fixture ground wire to the junction box ground wire by using a wire nut.
Connect the white fixture neutral wire to the junction box white neutral wire by using a wire nut.
Connect the black fixture hot wire to the junction box black hot wire by using a wire nut.
Align the canopy base over the mounting screws so that the screw heads come through the keyhole slots.
Shift the canopy base slightly until the screws are at the small end of the keyhole slots.
Tighten the mounting screws until the canopy base is snugly seated against the ceiling. Be sure that the wires are placed properly within the junction box.
Place the diffuser on the canopy. Then place the metal ring on the diffuser. Let the 4 screws from the ring mount tubes protrude through the holes in the metal ring.
Twist the 4 decorative nuts onto the ring mount tubes to secure the ring and diffuser.
The installation is complete. Restore power to the fixture and verify the fixture operates properly.

CCT Color Selection

Color Changing Temperature Adjustment, CCT (if desired).

Adjust CCT switches on each board accordingly to the desired color temperature as seen below. All boards must be set the same way.
Note: Fixture is preset to 3000K from the factory. Power to fixture must always be turned OFF prior to adjusting CCT switches.

COLOR TEMPERATURE ADJUSTMENT SETTING Maxxima MCL 3324900B 32 Inch 3 CCT
Selectable Oval LED Ceiling Mount - fig

3 YEAR WARRANTY

Maxxima extends a 3-year limited warranty to the original purchaser that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. A limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.

info@maxximastyle.elytsam.com
866-MAXXIMA(629-9462)
www.moc.elytsam.com
125 Cabot Court Hauppauge NY 11788
RIS9864

Documents / Resources

| Maxxima MCL-3324900B 32-Inch 3 CCT Selectable Oval LED Ceiling Mount [pdf] Installation Guide
MCL-3324900B, 32-Inch 3 CCT Selectable Oval LED Ceiling Mount, MCL-3324900B 32-Inch 3 CCT Selectable Oval LED Ceiling Mount
---|---