DIGITUS DN-650105 Industrial Fast Ethernet Switch 5 Ports Installation Guide
- June 5, 2024
- DIGITUS
Table of Contents
Industrial Fast Ethernet Switch
Quick Installation Guide
DN-650105 (5-port) • DN-650106 (8-port)
Rev2-0
Package Contents
Check the following contents of your package:
- 1 x Network Switch
- 1 x User Guide
- 1 x Terminal block
- 1 x DIN Rail mount
If any part is lost and damaged, please contact your local agent immediately.
Introduction
The Industrial Fast Ethernet Switch is designed for harsh environments where it is exposed to moisture, temperature fluctuations, and vibration. With a temperature range of -40°C to 85°C, the Industrial Fast Ethernet Switch can be used under the most adverse conditions. It ensures constant availability in highly sensitive areas such as transport, production, traffic, and safety monitoring. The simple plug-and-play system allows the Industrial Fast Ethernet Switch to be quickly integrated into the respective environment. With its Fast Ethernet connectivity, the Industrial Fast Ethernet Switch is a flexible, cost-effective solution for the industrial environment.
Hardware Description
Front Panel
The Front Panel consists of Ethernet Ports.
The LED indicators are also located on the panel.
DN-651105
DN-651106
LED indicator
| LED | Color | Function |
|---|---|---|
| PWR | Red | Off: No Power supply |
Light: Indicates the switch has power
LINK| Orange| Off: No device is connected to the corresponding port
Light: Indicates the link through that port is successfully established
at 10/100 Mbps
Blink: Indicates that the Switch is actively sending or receiving data
over that port
Upper Panel
The upper panel has a standard 6-Pin industrial power input terminal for
double redundant power backup and accepts DC power input.
Power input
This unit provides a 6-pin terminal block. It can be operated using a 12-48 V
DC power source. Always make sure your input voltage is within this supported
voltage range.
To connect power:
This unit supports two power inputs. Follow the printed polarity for +P1-,
+P2-, and ground. Connect positive wires to V+, connect negative wires to V-,
and connect a neutral wire to the ground mark.
+P1- is for power input one connection (PWR1).
+P2- is for power input two connection (PWR2).
Figure:
WARNING:
Always SHUT OFF the power source to connect the power wire.
WARNING:
Any exceeded input voltage will not make this unit function and may damage
this unit.
Grounding column
The switch already comes with a lightning protection mechanism.
You can also ground the switch through the PE (Protecting Earth) with Ground
Cable.
Installation of the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions to avoid incorrect installation causing device damage and a security threat.
- Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with a wet cloth or liquid
- Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis
- Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall
- Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction
- Make sure that the operating voltage is the same one labeled on the switch
- Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks
DIN-Rail Mounting
The DIN-Rail is already screwed on the Industrial Equipment.
Please refer to the following figures and know how to hang the Industrial
Equipment:
Step 1: Lightly press the button of DIN-Rail on the track.
Install Industrial Equipment in DIN-Rail mount.
Step 2: Check the DIN-Rail is tightly on the track.
Remove DIN-Rail Mounting
Step 1: Please refer to the following procedures to remove the Industrial
Equipment from the track.
Remove Industrial Equipment in DIN-Rail mount.
Step 2: Lightly press the button of DIN-Rail for removing it from the track.
Specifications
Model| Industrial 5-Port Fast Ethernet Switch| Industrial 8-port
Fast Ethernet Switch
---|---|---
Standard| IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x
Network Media (Cable)| 10BASE-T: UTP category 3, 4, 5 cable (100m)
100BASE-TX: UTP Category 5 cable (100m)
MAC Address Table| 2K, Auto-learning, Auto-aging
Transfer mode| Store-and-Forward
Switching Capacity| 1Gbps| 1.6Gbps
Input power supply| DC:12-48V
Dimensions (LWH)| 1288634mm| 15712048mm
Fan| Fanless
Temperature| Operating Temperature: -40°C — 85 °C
Storage Temperature: -40 °C — 85°C
Humidity| Operating Humidity: 0%” 95% non-condensing
Storage Humidity: 0% — 95% non-condensing
Surge Protection| Differential mode ±4KV Common mode ±6KV
MTBF| 300,000 hours
Electrostatic standard| Contact 8KV,air 15KV
This is a Class A product. In-home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures. Hereby Assmann Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below-mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>