ZYXEL WAX630S 802.11ax Dual-Radio Unified Pro Access Point User Guide

ZYXEL WAX630S 802.11ax Dual-Radio Unified Pro Access Point User Guide

Hardware Installation

Connect the UPLINK port to a router with Internet access. If you are not using PoE, connect the WAX63OS power socket to an appropriate power source.

Ground first for additional protection (see the Grounding section in this guide).

Wait until the LED blinks green

App Installation

Use Zyxel Nebula Mobile app to add a device in the NCC

Download and open the Zyxel NebulaMobile app. Log in with your my zyxel account.

Create an organization and site or select an existing site. Scan the WAX63OS’s QR code to add it to the site. (You can find the QR code in its web configurator or on a label on the device or its box.)

Note: The WAX63OS will go into cloud management mode automatically after it is registered to a site.

**Where to find QR code:

**

Web Configurator or Lebel on the device.

Cloud Web Installation

Use MAC address and serial number to add a device in the NCC

Follow the steps below to manage the WAX630S through the Zyxel cloud-based network management system.

Note: Make sure the connected router has Internet access.

1. Go to the Zyxel Nebula Control Center tNCC) website (https://unebulo.zyxel.com). Click Get Started to sign up for a myzyxel account and log in.
   

2. Create an organization and a site (network) in the NCC.

3. Enter the WAX63OS’s LAN MAC address and serial number (S/N) (see the label on the device) in the NCC configuration screen.
   Note: The WAX63OS will go into cloud management mode automatically after it is registered to a site. See the NCC User’s Guide for more information about configuring the WAX63OS through the NCC.

Local Web Installation

WiFi connection

From a WiFi enabled computer, search for the WAX63OS’s default WiFi network name (Zyxel-xxxx, where xxxx is the last four characters of the MAC address) and connect to it.

Open your web browser and enter “http://1.1.1.1 (setup.zyxel.com)” for initial configuration. Enter the default user name (admin) and password (1234). Click Login.

Note: If the WAX630S cannot connect to the Internet, use the DHCP- assigned IP address of the WAX63OS to access its web configurotor. Check the connected router or DHOP server for the IP address of the WAX630S.

http://1.1.1.1 or setup.zyxeI.com
(First time configuration only)
**** User Name: admin
Login Password: 1234 (default)

Wired connection

1. Use an Ethernet cable to connect your computer to the UPLINK port of the WAX630S through a PoE injector or PoE switch.
   Use its DHCP-assigned IP or default static IP address “http://192.168.1.2” to access the web configurator. Make sure your computer IP address is in the same subnet as the WAX63OS’s.
   
   http://192.168.12
   User Name: admin
   Login Password: 1234 (default)
   

2. The wizard appears automatically. Use the wizard to set up your WAX630S. Note: It takes 1 to 2 minutes to apply your wizard changes. The LED turns steady blue if you change the WAX630S default settings and the WIFI Is on.
   

3. Use the WAX630S’s new wireless settings (SSID and key) to re-connect to the WAX630S’sFi network for Internet access if you change them in the wizard (or log in to the web configurotor when the WAX630S is using a WiFi connection). The LED turns steady green when WiFi clients connect to the WAX630S .
   Note : The 1.1.1.1 (setup.zyxel.com) is for initial setup only. It is not usable after the WAX630S is configured.
   Note : Check the Dashboard screen and note down the WAX630S’s IP address In case you need to access its web configurator again.
   

Wall / Ceiling Mounting

1. a. Wall mounting: Drill two holes for the screw anchors (A), 62.4 mm apart. Insert the screw anchors into the wall.
   b. Ceiling mounting: Drill two holes for the screw anchors (A), 62.4 mm or 70.1 mm apart. Insert the screw anchors into the ceiling.
   

2. Install two mounting screws through the holes on the bracket (B) into the plugs/anchors to secure the bracket to the wall/ceiling. Make sure the screws are snugly and securely fastened to the wall/ceiling.

3. After the bracket is attached to the wall/ceiling, slide the WAX630S onto the bracket until it clicks into place.
   

T-bar Ceiling Mounting

1. Attach two clips to the ceiling grids as shown.
2. Install two screws to secure the bracket to the clips.
3. Slide the WAX63OS onto the bracket until it clicks into the place.
   Note: Clips (ACCESSORY-ZZO1O5F) are sold separately
   

Grounding

1. Remove the M4 ground screw from the WAX63OS‘s rear panel as shown. Secure a green/yellow ground cable (18 AWG or smaller) to the WAX63OS’s rear panel using the M4 ground screw.
2. Attach the other end of the ground cable to a wall or the ground. Follow your country‘s regulations and safety instructions to electrically ground the WAX63OS properly. Qualified service personnel must confirm that the building‘s protective earthing terminal is valid.
   

Support Information

EU
https://support.zyxel.eu

USA
+1800 255 4101
support@zyxel.com

See the User’s Guide atwww.zyxeI.com for more information, including customer support and safety warnings.

EU Importer
Zyxel Communications A/S
Gladsaxevej 378, 2. th. 2860 Søborg, Denmark
https://www.zyxel.com/dk/do/

UK Importer
Zyxel Communications UK Ltd.
2 Old Row Court, Rose Street, Wokingham,
RG40 1XZ, United Kingdom (UK)
https://www.zyxel.com/uk/en/

US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
https://www.zyxel.com/us/en/
Copyright Ô 2021 Zyxel and/or its aMliates. All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>