CPG 351FGCs Powered Convection Ovens100DD Deep Depth Ga User Manual

CPG 351FGCs Powered Convection Ovens100DD Deep Depth Ga

INTRODUCTION

Congratulations on your purchase of Cooking Performance Group commercial cooking equipment! At Cooking Performance Group, we take pride in the design, innovation, and quality of our products. To ensure optimal performance, we have outlined the following instructions and guidelines in this manual carefully for your review. Cooking Performance Group declines any responsibility in the event users do not follow the instructions or guidelines stated here.

Product Overview

The 351FGC100DD(L/N) features a sturdy steel construction with 4 adjustable legs. It is equipped with one built-in convection fan per oven cavity. The automatic ignition system activates in the event of a flameout, and a shutdown device stops the system from trying to ignite the burner(s) after 3 unsuccessful attempts to ensure safety. The electronic automatic thermostat ensures accurate temperatures for precise cooking. The 351FGC200DD(L/N)K features two oven cavities, helping you meet higher production demands.

Safety Precautions

CAUTION:
Failure to comply with the following operation instructions could lead to potential hazards and/or unsafe practice and could result in injury and damage to product and property.

NOTICE:

•  Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association, Inc., states in its NFPA96 latest edition that local codes are “Authority Having Jurisdiction” when it comes to requirement for installation of equipment. Therefore, installation should comply with all local codes.
•  This product is intended for commercial use only. Not for residential use.

WARNING:

•  Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other equipment.
•  Improper installation, adjustment, alteration, service or maintenance could lead to property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicingCPG equipment. This manual must be retained for future reference.
•  A licensed installer must handle all maintenance and repair.

Gas Pressure

•  The appliance and its individual shutoff valve (to be supplied by user) must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSI (3 .45 kPa).
•  The appliance must be isolated from the gas supply piping system by closing its individual manua shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 / 2 PSI (3 .45 kPa)

Stacking Ovens Instructions

1.  Dismantle the original flue assembly. (Fig. 1 A)
2.  Install the caster plate. (Fig. 1 B)
3.  Install the casters or legs. (Fig. 1 C)
4.  Align the top notches of the lower oven with the notches on the bottom of the upper oven. (Fig. 2)
5.  Attach the top and bottom unit with connecting plates and screws. (Fig. 3)
6.  Attach the stacked flue with screws (Fig. 4)
7.  Stacking is complete.

Specifications

Installation

• 1. Remove packaging before beginning installation.
• NOTE: Some parts are protected with an adhesive film. Remove any glue residue with approved substances, such as Noble Chemical Strike All Purpose Cleaner (#147STRIKE1G); never use abrasive substances. (See
• Cleaning & Maintenance on pg. 12 for our other recommended cleaning agents and further cleaning instructions)
•  Mount the feet and adjust the height by loosening or tightening each foot to ensure the unit is level.
•  The gas/electrical connections must be close to the equipment and easy to reach. You must use a new gas hose to connect to this unit.
•  Place the unit under an exhaust hood, ensuring you comply with your local regulations.
•  Install the unit at least 2″ from the wall and at least 6″ from other heat-producing equipment. Any wall, surface, cabinet, table, etc. in close proximity to the equipment should be made of non-combustible materials with proper thermal insulation.
•  Law provisions, technical regulations, and directives: The manufacturer requires the installation to be performed according to national and local codes and must be performed by a licensed installer.
•  Turn on the electric and gas valves:
  • . Manually remove the wing nut located above the control panel (Fig. 1) and carefully open the control panel. (Fig. 2)
  • . Remove the screws on the back of the oven, then open the right side panel. (Fig. 3)
  • . Check to ensure that the electric and manual intake valves are open. (Fig. 4)
  • . Reinstall the right panel, then reattach the control panel with the wing nut.
• NOTE: For complete shutdown follow these instructions, but instead close the electric and manual intake valves

Startup

Gas Connection

1. The serial plate is located on the side panel. It indicates the type of gas the unit is equipped to use. All equipment is set for use with the specified gas type at the factory.
2. The equipment is design-certified for operation on either natural or propane gas; it should only be connected to the type of gas for which it is equipped as stated on the serial plate.
3. A 3/4″ NPT inlet is located at the rear for the gas connection. The external regulator provided with the unit must be installed. An adequate gas supply is imperative. Undersized or low pressure lines will restrict the volume of gas required for satisfactory performance.
4. An adequate gas supply line to the unit should be no smaller than 3/4″ diameter.
5. Ensure the supply line is clean before connecting the line to the unit.
6. All pipe joints and connections must be tested thoroughly for gas leaks. Use only soapy water for testing on all gases. Never use an open flame to check for gas leaks. Gas Elevation Guide

Electrical Diagram

Control Panel

Operating Instructions

• Lighting, Relighting, and Shutdown Instructions
•  To light the oven, flip the power switch at the top left corner of the control panel to the “ON” position.
• The oven is equipped with a direct hot surface ignition system. There is no pilot to light.
•  Turn the oven to the desired temperate. The burners should be automatically ignited with the hot surface ignition system. If the burners fail to ignite within 4 seconds, the oven will automatically shut off the gas. Wait 5 minutes to allow the gas that was released to dissipate, and try to light the burners again. If the burners still fail to ignite after 3 such attempts, the oven will stop trying, even though the power switch is in the “ON” position. To continue to attempt to light the burners, turn the power switch “OFF” and then “ON” again.
•  To shut down the oven, flip the power switch to the “OFF” position. For a complete shutdown, also open the control panel and remove the right side panel. Turn the manual electric and gas valve to the “OFF” position. Re-attach the right side panel. (See Installation, step 7 on pg. 6 for further instruction)

Cooking Instructions

•  Turn the oven ON using the Power Switch at the top of the control panel.
•  Select the desired fan speed using the Fan Speed switch. The appropriate fan speed (HI or LOW) depends on the type of food being cooked.
•  Switch the Fan Mode to COOK. The fan will run continuously when the oven doors are closed (the fan does not cycle on and off with the heating element). If this switch is set to COOL, the only difference is that the fan will continue to run when the oven doors are open.
•  Set the cooking temperature by turning the Cook Temperature Control until the indicator mark on the knob is pointed to desired cooking temperature. The HEAT ON indicator will light when the heating element is on and will remain on while the oven preheats.
•  Wait until the HEAT ON indicator has gone out. At that time the oven will have reached the set cooking temperature.
•  Open the oven doors, load the product into the oven, and close the doors.
•  You can use the Cook Timer as a reminder of when to remove product from the oven. Turn the Cook Timer knob until the indicator mark points to the desired cooking time (up to 55 minutes). The timer knob will rotate counterclockwise as the timer runs down, indicating how much time remains. You can turn the knob while cooking to increase or decrease the remaining time. When the timer runs out, a buzzer will sound for a short time, then turn itself off. (To immediately silence the buzzer, turn the Cook Timer knob to the OFF position.)
• NOTE: The timer is a reminder to you; the timer does not control the oven.
• If you open the oven doors, the heating element and fan will shut off until the doors are closed. However, the timer will continue running even if the doors are open.
• For ovens that are equipped with an oven interior light, to turn on the light, press and hold th switch located at the bottom of the control panel.

Cleaning & Maintenance

•  Before cleaning, turn off the unit and let it cool down.
•  Carefully clean the equipment daily to promote proper operation and long life.
•  Steel surfaces must be cleaned with with cleaning agents such as Noble Chemical Sunbright, Noble
• Chemical Knockout, or Noble Chemical Blast, diluted in very hot water using a soft cloth; do not use abrasive powder detergents or corrosive substances. The use of acids can affect the unit’s operation and safety. Do not use brushes, steel cottons, or abrasive disks made with other metals or alloys that may cause rust stains due to contamination. For the same reason, avoid contact with iron objects. Do not use stainless steel brushes, as they can cause damaging scratches.
•  Metal powder, metal shavings, and iron material in general can cause stainless steel to rust. Superficial rust stains may be present on new equipment and they can be removed with a detergent diluted in water and a scouring pad. If dirt is difficult to remove, a sponge may be used.
• Please note that rust is not covered by the warranty.
• . Use only approved substances to clean the unit as some chemicals could damage the unit. Rinse properly after cleaning with clean water, do not spray directly with water jet.
•  We recommend that the user subscribes to a maintenance agreement to have the equipment checked at least once per year by an authorized technician
•  Before carrying out any maintenance or repair, disconnect and unplug the equipment. Use only original spare parts supplied by Cooking Performance Group.
•  If the equipment is not going to be used for a long period of time, it is advised to clean the equipment and surrounding areas properly

References

• Cooking Equipment by Cooking Performance Group (CPG)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>