STIHL ALM 030 Viking iMOW 6 Series Blade Set 30cm Instruction Manual

: June 5, 2024
: STIHL

Table of Contents

For your safety
Standard equipment
Assembly and disassembly
Notes on mowing
Maintenance
Technical specifications
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

STIHL ALM 030
Instruction manual
A
INT 1

Mowing blade ALM030
The accessory ALM030 enables the lawn to be cut more quickly since it increases the cutting width of the robotic mower by 2 cm.

For this purpose, the mowing blade with a cutting width of 28cm was installed as standard, and the carrier plate on the robotic mowers from the RMI632 series are replaced with a mowing blade with a cutting width of 30cm and blade support.

Notes on the instruction manual:

This instruction manual constitutes the original manufacturer’s instructions in the sense of EC Directive 2006/42/EC.

STIHL is continually striving to further develop its range of products; we, therefore, reserve the right to make alterations to the form, technical specifications, and equipment level of our standard equipment.
For this reason, the information and illustrations in this manual are subject to alterations.

For your safety

1.1 General
These safety regulations must be observed when working with the machine.
** Read the entire instruction manual before using the machine for the first time. Keep the instruction manual in a safe place for future reference.
In addition, the entire instruction manual for the robotic mower must be read. This instruction manual supplements the instruction manual for the robotic mower.
A robotic mower with fitted accessory ALM030** is intended for mowing lawns.
The supplied mowing blade (cutting width 30cm) must only be used together with the blade support also supplied. Other combinations are not permitted.

Risk of death from suffocation!
Packaging material is not a toy danger of suffocation! Keep packaging material away from children.

Standard equipment

Item	Designation	Qty.
A	Mowing blade	1
B	Blade support	1
C	Fastening nut	1
–	Instruction manual	1

Assembly and disassembly

Risk of injury!
Activate the disabling device and put on gloves before performing any work in the area of the mowing blade.

Tilt the robotic mower onto its side and lean it securely against a stable wall.

3.1 Removing the mowing blade and carrier plate

Push in both tabs(1) on the carrier plate with one hand and hold. Remove fastening nut(2) with your other hand. Remove the mowing blade together with the fastening nut.
Insert puller(3) into the carrier plate as shown and turn anti-clockwise to the stop.
Support the machine with one hand, and remove carrier plate(4) by pulling on the puller(3).

3.2 Installing ALM030
Installing the blade support

Thoroughly clean the mowing deck and shaft of the motor.
Fit blade support(B) onto the shaft of the motor as shown.

Installing the mowing blade

Fit mowing blade(A) on blade support(B) as shown. Ensure the correct position of retainers(1) in the mowing blade. The guides(2) must be positioned in the slot of the mowing blade as shown.
Screw on the new fastening nut(C) as far as possible. Several clicks are audible during tightening. Ensure secure seating of the mowing blade by shaking carefully.
Following the installation of a new mowing blade, confirm the blade replacement in the “Service” menu (see instruction manual for the robotic mower).

3.3 Removing ALM030
Removing the mowing blade

Push in both tabs(1) on the blade support with one hand and hold. Remove fastening nut(C) with your other hand. Remove the mowing blade together with the fastening nut.

Removing the blade support

Insert puller(2) into the blade support as shown and turn anti-clockwise to the stop.
Support the machine with one hand, and remove blade support(B) by pulling on the puller(2).

Notes on mowing

4.1 Adapting the programming
The robotic mower mows the mowing area automatically as usual when the mowing blade ALM030 is fitted.

The bigger cutting width enables the mowing duration to be reduced by up to 10% – see the section “Adapting the programming” in the instruction manual for the robotic mower.

Maintenance

5.1 Maintenance operations

Weekly Carry out a weekly visual inspection of the mowing blade, blade support, and fastening nut for damage (notches, cracks, fractures, etc.) and wear.
Replace the mowing blade every 200 hours.
Replacement blade (30cm): 6309 702 0102

5.2 Cleaning

Clean the mowing blade weekly (e.g.with a brush). If the noise produced by the machine increases during mowing, remove any dirt from the mowing blade, blade support, and mowing deck housing more frequently. The mowing blade and blade support can also be installed offset by 180°.

5.3 Mowing blade maintenance

Risk of injury!
In particular, check for wear on the mowing blade; the same wear limits apply as for the original mowing blade.
The mowing blade, blade support, and fastening nut must be replaced if damaged (e.g.broken, worn).

Maintain the mowing blade as per the instruction manual for the robotic mower.
For information on removing and installing the mowing blade, see the sections “Removing ALM030” (⇒ 3.3) and “Installing ALM030”. (⇒ 3.2)

Technical specifications

The following technical data of the robotic mower changes when the accessory ALM030 is fitted:

Cutting width ……………………………… 30cm

Sound emissions:
In accordance with Directive 2006/42/EC and the EN 50636-2-107 standard:

Measured sound power level LwA…………64 dB(A)
Uncertainty KwA………………….3 dB(A)
LwA + KwA…………………………67 dB(A)
Sound pressure level LpA…………56 dB(A)
Uncertainty KpA………………….3 dB(A)

0478 909 9928 A
Printed on chlorine-free bleached paper. Paper is recyclable.
The cover is halogen-free.