VIETA BBT06 Wear Smartwatch User Manual
- June 5, 2024
- VIETA
Table of Contents
VIETA BBT06 Wear Smartwatch
Thank you for purchasing the Wear Smartwatch BBT06. To ensure correct operation, please read this manual carefully before use.
The adaptation platform requirements
Android 4.2 and above support. iOS 9.0 and above support. Bluetooth 4.0
App download method
You have these options:
Scan the QR with your smartphone to access to Da Fit application.
Android/Apple:
Android: search for “Da Fit” though the software application (Google Play
Store) to download and install the application.
Apple: search for ” Da Fit ” though the software application (Apple App
Store) to download and install the application.
IMPORTANT: The recommended Da Fit app versions for Android and iOS is
2.0.
IMPORTANT: Please instead of pairing from smartphone “Bluetooth”
settings, follow the steps described on “How to pair” (to get all the
Bluetooth communication between smartphone and watch).
NOTE: User can customize the wallpaper of the smartwatch with “Da Fit”
application. To do this, look for information in the application’s user
manual.
Care for Vieta Smart Wear before using
To ensure the normal use of smartwatch, please charge it before using it
for the first time. Please use matching charging cable to charge, and connect
the charging points on bracelet with the pin on the charger following the
correct position. For charging the smartwatch, please plug the USB end of the
charging cable into the USB port of a standard phone charger, desktop or
laptop computer with a standard 5V output. Not recommended to charge using
power bank as the output voltage is not of standard 5V. On the smartwatch
screen, the charging process will be displayed, showing the battery status.
Once charged it, the full battery will be displayed as full of charge. It’s
not possible to set the time of the smartwatch without synchronizing with the
Smartphone, because the watch time always show the same as Smartphone have. If
you set the time on your Smartphone, it will automatically sync to the
smartwatch.
NOTE: The battery consumption of the smartwatch is higher when it remains
connected and synchronizing data with your smartphone. Therefore, it’s
recommended keep it disconnected when you finish to use between them.
Charging Instructions
Connect the magnetic connector into the charging position as shown in the figure below, using smartphone charger 5V/1A.
Pair the Vieta Smart Wear with your smartphone
Turn on the smartwatch; press and hold the right button for many seconds to
turn the device on (and off).
Verify that your smartwatch is not connected to another smartphone before
connecting your smartphone. Otherwise, as the smartwatch is already connected
to another smartphone, you will not be able to connect yours. To verify this,
on the main watch screen, slide your finger from top to bottom to access the
basic settings center, and verify that the Bluetooth icon does not appear
(indicated in the image below), indicating that there is no active pairing
[Bluetooth unpaired (Disconnected)].
-
Bluetooth not paired.
(Disconnected from smartphone). -
Bluetooth paired.
(Connected to smartphone).
In the event that the icon appears without being connected to your smartphone,
check on the other smartphones that the disconnection was successful. Once the
smartwatch is cleared of Bluetooth connections, you can start the pairing
process with your smartphone.
Available the Bluetooth on your Smartphone. Active your GPS on the smartphone.
Go to the Da Fit application (previously downloaded on your smartphone), go to
“Devices” and select “Add a Device”. In the list, Vieta Wear will appear.
Select the device and verify that the status that appears is “Connected”.
When in the Da Fit application it appears as “Connected”, check the Bluetooth
icon on the clock.
IMPORTANT: Before the entire pairing process between Vieta Smart Wear and
your smartphone, it is important that you have activated the GPS location of
your smartphone, in order to start the pairing process.
IMPORTANT: This watch model allows you to manage incoming calls but not
talk through it. That is, you can only ignore or reject the call, but not
answer it You can connect a Bluetooth headset / speaker to your smartphone if
you wish, as you will be able to speak through the paired device.
Start-up functions of Vieta Smart Wear
Smartwatch right side button: use this button to;
Power ON/OFF: press and hold the button for many seconds to turn ON/OFF the device.
Standby (turn ON/OFF the display):
if you click once briefly on the button, it puts the clock screen in energy
saving state, and turns off the screen light
Return to the main screen:
when you are in an application of the smartwatch, pressing the button, you
will go back to the main screen of the device, thus existing the application
that you were previously viewing. When you are inside the any application, if
you slide you finger from left to right, you can go back to the previous screen
(without having to press the side button on the watch to go back to the main
screen).
Smart Watch Display;
By swiping from left to right, or from top to bottom, different function menus
will appear and become accessible by further selection.
IMPORTANT: The smartwatch must be paired first with smartphone. Press & hold on the wallpaper: Pressing and holding on the current wallpaper (watch face) for 2 seconds will bring out wallpaper selection menu, with wallpaper selections made available by swiping horizontally. The wallpaper then is selected, saved and replaced the existing wallpaper by clicking on wallpaper that you like.
Applications center: from the main screen, swipe from down to up to access the all applications directory; find my smartphone, Steps, Sleep, Heart Rate, Music… To exit from this directory, briefly press the right button on the Vieta Pro Wear.
Steps. Vieta Smart Wear automatically tracks steps taken, Calories
burned, Distance travelled and displays on the screen.
IMPORTANT: Your movement stats reset to zero at midnight.
Sleep. If you keep wearing Vieta Smart Wear in your sleep, it can provide
the hours slept and quality of sleep stats on both the screen and the Da Fit
app.
IMPORTANT: Sleep stats reset to zero at 8.00PM.
HR. Heart Rate Test: tap the heart rate icon to start measuring your heart rate. On the heart rate page, it can show the heart rate measured data of the last times.
MMHG. Blood Pressure Test: tap the blood pressure icon to start measuring your blood pressure. On the blood pressure page, it can show the blood pressure measured data of the last times.
SPO2. Tap the SpO2 icon to start blood oxygen level measurement. On the SpO2 page, it can show the blood oxygen level measured data of the last times.
Weather. Vieta Smart Wear could show the weather info of current and tomorrow on the weather page. Weather information is synced after connecting with the Da Fit application (it will not be updated after a long disconnected).
Camera. Remote shutter: after connecting the device can remote control
the camera on your smartphone.
IMPORTANT: You must have the phone unlocked, and the Da Fit application
running in the background, for this application to work.
The music player application will allow you to Play / Pause and change
the song that is playing on your smartphone.
IMPORTANT: You must have the music application running on your smartphone
before using the “Player” application of your smartwatch, since it is a
control application only. Music will not play through the watch.
Breathing: Application designed for relax, performing deep breathing following the steps; tap on “start”, breathe in for the seconds the watch vibrates, breathe out for the next few seconds.
These applications store data from previous measurements. When you will open each application, you will see the previous measurement. Then, to do a new measurement, tap on the application icon that you opened on the smartwatch.
Quick access to basic settings: on the main screen, swipe from top to
bottom to top to access to the quick access to Vibration (ON/OFF), Brightness,
Battery status, Bluetooth status and Settings.
If you select the “Configuration” option, you can access the following menu;
Other features include Stop clock, Reset, About information, Power Off and QR code, you will find on the “Configuration” option
Quick access to Training applications: on the main screen, swipe from
right to left to access to training applications..
Tap the training icon on the menu to start a new training measure recording,
there are 8 sport modes to be chosen. The last training recording will be
shown on the training page.
Notifications center: on the main screen, swipe from left to right to
access Notification center, where those notifications that are enabled on the
smartphone will be displayed.
Check in
your smartphone settings and in the app settings that notifications and
accepted permissions are enabled.
From the watch you can read or delete the notification (but not reply to the
texts). Read only.
Customize your wallpaper
The Vieta Smart Wear, has some wallpapers of the smart watch that are
editable, and therefore customizable through the Da Fit app.
-
Press and hold on the main watch display.
-
When the wallpapers appear selectable, slide your finger from left to right on the watch screen to select the editable wallpaper.
-
Select the editable wallpaper.
-
In the Da Fit application, under “Device”, go to “Wallpaper” option, and follow the steps to edit your wallpaper (for more information, access the Da Fit application manual on the manufacturer’s website).
Caution
Vieta Smart Wear is designed with IP67 water resistance. It can be in
contact with water in rainy conditions or washing hands, but not suitable for
submersing under water, showering or swimming. Synchronize the data every time
that you want to access any management and to access at any services of the
Vieta Smart Wear. Always use the charging cable to charge on this device
included on the box, and not cables from other products.
It’s recommended to keep the smartwatch bracelet out of places with humidity
or extremely high/low temperatures for a long time to avoid damages.
Don’t misuse the rear sensor or look directly into it to avoid possible
physical damage. Please don’t disassemble or open the smartwatch to avoid
physical damage.
Vieta Smart Wear maintenance
Protect the bottom sensor of your smartwatch. Clean the surface of the
smartwatch with dry cloth. Be very careful if you use soapy water for cleaning
(don’t use plenty of water) to remove oil or durst. Don’t expose the
smartwatch in environments with strong chemicals; gasoline, propanol, alcohol,
or insect repellent. Chemicals will damage the smartwatch and the surface
damages. Avoid letting your smartwatch be subject to strong impacts and
exposure to extremely high temperatures. Don’t disassembly the smartwatch,
will lose its water-resistance.
Common solutions guide
Cannot pair the smartwatch?
Make sure the smartwatch is turned on and activated, and that it’s not linked
to other smartphone. Place the smartwatch near the mobile phone and search
again. If it’s still invalid, turn off the Bluetooth of the smartphone for 20
seconds. Then, restart the Bluetooth and search it again.
Should the Bluetooth connection always be active? Will there be any
data if it’s closed?
Before syncing the data, the exercise and sleep data will be saved in the
smartwatch storage. When the smartphone and the smartwatch make the Bluetooth
pairing successfully, the smartwatch will automatically upload data to the
smartphone. Please, note that the data stored by the smartwatch is limited,
and it can only be stored about a week. When the space is full, the first data
will be automatically overwritten to save the last data. Therefore, please
sync the smartwatch with your smartphone on time.
Observations: the use of the applications related to the management and configuration of services in your smartphone, requires to have the smartwatch linked with your smartphone, if not, they cannot be used.
What should I do if the smartwatch cannot be charged?
Confirm whether the direction of the charger is correct, and the charger is in
the correct position contact the smartwatch.
After plugging in the charger, it will immediately enter the charging state.
If the smartwatch is turned off due to running out of battery, the screen will
take between 3 or 5 minutes to enter the charging state and it will
automatically start the watch.
To know the status of the battery, access the “Basic configuration” menu
described above.
Remove all information from the smartwatch (Reset Factory)
If data is stored (phone information…) on the smartwatch, and you want to
delete it completely to do a new synchronization with another Smartphone
device, in your watch go to Settings and select Reset).
Does wearing the smartwatch for a long-time harm to the human body?
The radiation from the device is lowly than the CE and FCC standard and is
smallest. Long-term use will not cause radiation damage to the human body.
Specification
| Model Name. | Vieta Smart Wear. |
|---|---|
| Bluetooth Version. | Bluetooth 4.0. |
| Dimension. | 43.8*9.9mm. |
| Material. | Aluminum. |
| GPS. | Yes. |
| Wi-Fi. | No. |
| Call Mode. | No. |
Bluetooth headphones connected to the smartphone at the same time as the
smartwatch?| Yes.
Display screen.| 1.3 inch.
Chipset.| Nordic52832.
Operation temperature.| -10°C to 40°C.
Storage temperature.| -3°C to 30°C.
Storage humidity.| 20%~75%.
Battery.| 200mAh.
Input Power.| 5V/1A.
Net weight.| 35g.
Declaration of conformity
Issuer’s name: FRAMASON AUDIO S.A
Address: Av. de Pau Casals 7, 2- 08021 Barcelona
Tel: +34 93 1162491
CIF: A62829841
We declare under our own exclusive responsibility that the product:
- Description: Smart watch
- Brand: Vieta Smart
- Model: BBT06
- Manufacturer: FRAMASON AUDIO S.A
- Manufacturing country: China referred to in this declaration is in compliance with the essential norms and standards
EMC
- EN 301 489-1 V2.2.0
- EN 301 489-3 V2.1.1
- EN 301 489-17 V3.2.0
- EN 301 489-52 V1.1.0
RF
- EN 300 328 V2.1.1
- EN 303 413 V1.1.1
- EN 300 330 V2.1.1
- EN 301 908-1 V11.1.1
- EN 301 908-2 V11.1.2
- EN 301 908-13 V11.1.2
- RoHS: EN50581:2012
- EN 50360:2017
- EN 50566:2017
- EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
In conformity with the provisions of the Directive 2014/53/EU, 2009/125/EC and 2011/65/EU of the European Parliament and of the Council and UL/11716634 of 5th July 2019.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>