AVANTCO MX30 Gear Driven 30 Quart Commercial Mixer User Manual
- June 5, 2024
- AVANTCO
Table of Contents
- AVANTCO MX30 Gear Driven 30 Quart Commercial Mixer
- Parts Overview
- Standard Accessories
- Unpacking the Equipment and Initial Setup
- Operation Instructions
- Mixer Capacity Chart
- GEAR AXLE
- INITIATIVE AXLE
- FORK
- CHANGE SPEED AXLE
- TURNING PLATE AND MIXING AXLE
- SINGLE PHASE MOTOR DIAGRAM
- CENTER AXLE
- Cleaning
- Troubleshooting
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AVANTCO MX30 Gear Driven 30 Quart Commercial Mixer
Parts Overview
Standard Accessories
Item | Description | Qty |
---|---|---|
1 | Flat Beater | 1 |
2 | Dough Hook | 1 |
3 | Wire Whip | 1 |
4 | Bowl | 1 |
NOTES:
- Any agitator is easily installed by simply raising it onto the mixing axle, and the rotating it clockwise on the shaft until it locks into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate counter-clockwise and lower.
- All of the accessories are precisely fitted to the bowl, have rounded corners, and are easily removed for cleaning.
Unpacking the Equipment and Initial Setup
Carefully remove crating or packaging materials from the equipment. Models shipped on pallets are bolted to the pallet. Bolts must be removed to safely separate the equipment from the pallet. Place the equipment on a flat surface with sufficient space around the mixer to allow for safe cleaning and service. Plug only int grounded electrical outlets matching the nameplate rated voltage. Do not use an extension cord with this equipment. Do not plug this equipment into a power strip or multi-outlet power cord.
INSTALLATION:
- Read this manual in its entirety prior to installation and operation. DO NOT install if you do not understand everything in this manual.
- Select a location for the mixer keeping in mind that:
- Surface must be level
- Location should be accessible for maintenance and service
- Location should offer adequate clearance for installing and removing agitators, bowls or attachments
- Location offers sufficient space for adding ingredients to the mixer
- Make sure that the rear ventilation outlet of the mixer is not blocked
Operation Instructions
Mixing: Always use the correct attachment for the job.
- A. Wire Whip: Suitable for mixing liquids and soft ingredients, can work in all speeds. Do not run for more than 15 minutes.
- B. Flat Beater: Suitable for mixing dry ingredients, can work in low & medium speeds only. Do not use in high speed. Do not run for more than 15 minutes.
- C. Dough Hook: Suitable for mixing dough, can work in low & medium speed only. Do not use in high speed, do not run for more than 20 minutes. Absorption ratio must be more than 50%. Refer to mixer capacity chart.
Mixer Capacity Chart
When mixing dough ( pizza, bread or bagels), check your “AR” absorption ratio
– water weight divide by flour weight. Above capacities based on 12% flour
moisture at 70°F water temperature. If high gluten flour is user above dough
batch size by 10%.
Example: If recipe calls for 5 lb. of water and 10 lb. of flour, then 5
divided by 10 = 0.50 x 100 = 5 AR.
- 2nd Speed should never be used on mixtures with less than 50% AR.
- Do not use attachments on hub while mixing.
When calculating the correct size mixer for your application, here are some
helpful weights & meases
8.3 lb. = 1 gallon of water – 2.08 lb. = 1 Quart.
GEAR AXLE
INITIATIVE AXLE
FORK
CHANGE SPEED AXLE
TURNING PLATE AND MIXING AXLE
SINGLE PHASE MOTOR DIAGRAM
CENTER AXLE
Cleaning
All new mixer bowls and accessories including whips, beaters, and dough hooks should be properly washed before use. Wash with hot water and a mild soap solution and then rinse off with either a mild vinegar or soda solution and then rinse again with clean water. It is highly recommended this cleaning procedure is followed for bowls and accessories prior to whipping egg whites or whole eggs. The mixer should be cleaned daily with a clean damp cloth. If the unit has not been used for some time, it is recommended that the procedure above is followed before mixer use. It is important that the rear bowl lift guides are greased every three months to prevent corrosion.
Troubleshooting
Trouble | Possible Causes | Solution |
---|---|---|
The axles can’t work when operating the machine | Poor contact of the | |
electrical equipment | Check the Plug | |
The mixing bowl is out of position | Moving direction is not correct | Change |
Leaks oil | Sealing washer is damaged | Change |
Difficult to move the bowl up and down | Slideway is rusted | Clean the slideway |
and lubricate
The motor is overheated| The voltage is not enough, or| Check the voltage or
use
and speed is down| incorrect speed| lower speed
Noise and overheating| Poor lubrication| Add or change lubrication
Mixer touches bowl| The mixing device or bowl de- formed| Repair or change the
bowl or mixing device
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>