AVANTCO EQUIPMENT 177PBD3 Powdered Beverage Dispenser User Manual

AVANTCO EQUIPMENT 177PBD3 Powdered Beverage Dispenser

Specifications

Model No.| Voltage| Heater Power| Water Reservoir| Hot Water Tank| Powder Canister| Dimensions| Weight
---|---|---|---|---|---|---|---
177PBD3| AC120V 50Hz| 1600W| 5L| 1.8L| 3pc x 2.5L/pc| 315mm(W) x 470mm(D) x 665mm(H)| 48.5 lb.

Installation

1. Unpack the machine and check for damage and missing parts.
2. Place the unit on a stable, flat surface near the power and water supply.
3. Maintain adequate ventilation with a distance of 6 in. from walls.
4. Leave 60 in. of free space in front for easy use and maintenance.
5. Attach the water line to the rear inlet, and tighten with a wrench.
6. Turn on the water supply, check for leaks, and tighten fittings if needed.
7. Connect the power supply cord.
8. Run a full inspection before first use to check functions.

Operation Instructions

1. Connect the machine to the power supply.
2. Turn the toggle switch to ON after verifying water supply is ON.
3. The unit will start filling with water, and the LED display will show FIL.
4. Add powdered ingredients:
   • Rotate the ingredient outlet arrow.
   • Raise the canister, open the lid, fill it with ingredients.
   • Connect the axle, and stall canister, and rotate the outlet for use state.

FAQ

• Q: What should I do if the machine is not dispensing properly?
  • A: If the machine is not dispensing properly, check if the powder canister is properly installed, ensure the ingredients are not clogged, and run a cleaning cycle as per the manual instructions.
• Q: Can I use flavored powders in the dispenser?
  • A: Yes, you can use flavored powders in the dispenser. Ensure the powders are suitable for use in beverage dispensers and follow the recommended cleaning procedures to prevent clogs or flavor mixing.

Safety

• This appliance is designed for COMMERCIAL USE ONLY.
• DO NOT use outdoors.
• DO NOT alter or deform the power cord or plug in any way. This may cause electrical shock and/or damage unit.
• Do not pull the power cord.
• ALWAYS use on a circuit that is properly protected and capable of the rated load.
• DO NOT operate the dispenser unless it is properly grounded.
• Cleaning & maintenance should only be performed by properly trained persons with supervision.
• This unit is NOT intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge.
• Children should be supervised to ensure that they do not play with the appliance.
• ALWAYS unplug unit from the power supply before cleaning or servicing.
• DO NOT submerge or saturate with water, the unit is not waterproof.
• Install the machine in a dry area away from water and water splashes.
• DO NOT operate if your hands or feet are wet.
• Please keep 15cm (6″) minimum air space all around the dispenser.

Specifications

Parts Identification

Parts Identification (Front)

Button Board (B)

Mode Switch (G)

Parts Identification (Back)

**Installation

**

• NOTE : Please use filtered and softened water. If using ground or tap water, please soften it first.

1. Carefully unpack the machine and check for damage and missing parts.
2. Place the unit on a stable, flat surface in a dry area near the power supply and water supply. Do not connect the water line or power cord at this time.
3. For adequate ventilation, when installing the unit, maintain a distance of 6 in. between the unit and walls or other obstacles. Increase the distance if the unit is placed near a heating source.
4. Leave 60 in. of free space in front of the machine to allow for easy use and maintenance.
5. Attach the water line to the inlet located on the rear of the dispenser. Hold the water inlet fitting with a wrench when tightening the water line.
6. Turn on the water supply. Make sure to check for leaks at the water inlet. Tighten fitting if needed.
7. Connect the power supply cord to the power supply.
8. Run the full inspection upon turning on the unit and prior to first use.
   • Upon full inspection, the unit will check the functions of the powder dispensing motor, mixing motor, and water outlet. (See “Menu Functions” on page 7 for more information on running the full inspection.)

Operation Instructions

• NOTE:   for specific programming instructions.

1. Connect the machine to the power supply.
2. Verify that the water supply is ON, then turn the toggle switch to the ON Position.
3. The unit will begin filling with water and the LED display will show “FIL”.
4. Add your powdered ingredient:
   • (a) Follow the arrow to rotate the ingredient outlet.
   • (b) Raise up the front side of the canister and take it apart.
   • (c) Open the lid, and fill the canister with ingredients.
   • (d) Connect the axle and stall canister.
   • (e) Follow the arrow to rotate the ingredient outlet to use state.
5. Set the water temperature. (See “Menu Functions” below for more information on setting the water temperature.)
   • After setting the water temperature the unit will display “HEA” while it heats up to temp.
   • Once the unit reaches the desired temp, it will display “rEA”.
6. Program the output volume of water and powdered ingredients to be dispensed from each drink option. (See “Data Settings” on page 8 for more information on setting volume output.)
7. Place the cup under the dispenser and press the drink button of your choice to dispense your beverage.

Programming Instructions

Button Board

Mode Switch

Menu Functions

1. To activate all menu functions, press the “Mode” button located on the inside panel of the door.
2. After pressing “Mode,” the LED Display will show “SET.” You can now navigate through the menu settings.
3. Cycle through the menu settings by pressing the “Menu” button.
4. There will be four available setting screens for you to navigate shown in the chart below. Press “Menu” until you reach your desired screen.
5. When you are finished altering settings, press “Mode” again to save and exit.

Screen| Default| After| Function Setting| Description| Save
---|---|---|---|---|---

1

|

“CLA”

|

Auto Cleaning

| When the unit displays “CLA”, press “Drink A”. Machine will clean pipe and mixing chamber automatically.|

Mode

2

|

“000”

| Ex. “095”

equals 95 degrees

|

High Temp.

| Use “+” and “-” to adjust the temperature. Unit will display “HEA” while it reaches temp.

3

|

“000”

| Ex. “090”

equals 90 degrees

|

Low Temp.

|

Use “+” and “-” to adjust the temperature.

4

|

“CHE”

|

Full Check

| When the unit displays “CHE”, press “Drink A”. Machine will check the functions of powder dispensing motor, mixing motor, and water outlet.

Data Settings

1. To activate all drink data setting functions, press the “Mode” button located on the inside panel of the door.
2. After Pressing “Mode,” the LED display will show “SET.” You can now navigate through the drink data settings.
3. Cycle through the menu settings by pressing the drink button in which you would like to alter settings for. (Example: “Drink A”)
4. There will be four available setting screens for you to navigate shown in the chart below. Press the “Drink” button until you reach your desired screen.
5. When you are finished altering settings, press “Mode” again to save and exit.

Screen

|

Default

|

After

|

Function Setting

|

Description

|

Save

---|---|---|---|---|---

1

|

“000”

|

Ex. “025”

|

Price

|

Increase and reduce by pressing buttons “+” and “-”.

|

Mode

2

|

“A-1”

|

Ex. “065” equals

6.5 seconds

|

Water Volume

| The number shown on LED is the water dispensing time, for example, “065” means 6.5 seconds. Increase and reduce by pressing buttons “+” and “-”.

3

|

“A-2”

|

Ex. “030” equals

3 seconds

|

Powder Volume

| The number shown on LED is the powder dispensing time, for example, “030” means 3 seconds. increase and reduce by pressing buttons “+” and “-”.

4

|

1A000000

| Ex. “1A000029”

equals 29 cups sold

|

Sales

|

Increase and reduce by pressing buttons “+” and “-”.

Cleaning

• DO NOT use harsh chemicals or abrasive materials.
• DO NOT submerge or saturate with water, unit is not waterproof.
• Cleaning should be done at the end of every workday.
• Only those persons trained and qualified in equipment repair should attempt to clean the inside of this dispenser.

To clean the outside of the machine:

1. Turn the ON/OFF toggle switch to OFF, unplug, and allow unit to completely cool before cleaning.
2. Use a clean cloth with hot water mixed with Noble Chemical Sunbright liquid dish soap (or a neutral soap) to clean the outside of the unit.
3. For dirt smudges on the unit’s exterior, a damp cloth will suffice.

To clean the inside of the machine:

1. Remove powder canisters and empty of all powder. (See “Operation Instructions” on page 6.)
2. Run the cleaning menu function. (“CLA” is the first screen of the menu functions.)

Note:

Please read the manual thoroughly prior to equipment setup, operation, and maintenance.

• www.AvantcoEquipment.com

• www.AvantcoEquipment.com

References

• Avantco Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>