DENALI D-14 Headlight Bracket Instruction Manual

September 16, 2024
DENALI

D-14 Headlight Bracket

“`html

Specifications:

  • Product Name: D-14 Headlight Bracket
  • Model: Harley Davidson Street Glide DNL.D14.10100.K

Product Information:

The D-14 Headlight Bracket is designed for Harley Davidson
Street Glide models. It includes a headlight bracket, adhesive foam
tape, headlight harness, and a D14 DOT headlight. The installation
requires basic tools such as an Allen Key Set, Torx Bit Set,
Phillips screwdriver, and a 12mm socket or wrench.

Installation Instructions:

1. Disassembly

  1. Remove The Headlight Bezel:

  2. Remove the single philips head screw located at the bottom of
    the light.

  3. Pull the bezel forward to detach it from the bike.

  4. Remove Headlight:

  5. Remove the three allen key screws holding the light to the
    bike.

  6. Disconnect the factory wiring harness from the 5 pin
    connector.

2. Installing The Headlight Harness

  1. Install The DENALI Headlight Harness:
  2. Run the power leads to the battery.
  3. Plug the 4 pin headlight connector into the factory headlight
    harness.

3. Attaching Headlight To Bracket

  1. Attach Headlight To Bracket:

  2. Install the DENALI headlight into the bracket using the
    supplied hardware.

  3. Fasten the bracket to the upper mounting hole on the
    headlight.

FAQ:

Q: What should I do if I encounter issues during

installation?

A: If you encounter any difficulties during installation, please
reach out to our gear experts at 401.360.2550 or visit
WWW.DENALIELECTRONICS.COM for assistance.

“`

Instruction Manual
D-14 Headlight Bracket
Harley Davidson Street Glide DNL.D14.10100.K
What’s In The Box?
(a) (b)

Instruction Rev00

DENALIELECTRONICS.COM

Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra mile to make sure our instructions are clear and as easy to understand as possible. If you have any questions, comments, or suggestions don’t hesitate to give our gear experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. DENALI takes no responsibility for damages caused by improper installation. Caution: When installing electronics it is extremely important to pay close attention to how wires are routed, especially when mounting products to the front fender, front forks, or fairing of your motorcycle. Always be sure to turn the handlebars fully left, fully right, and fully compress the suspension to ensure the wires will not bind and have enough slack for your motorcycle to operate properly.

Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws, nuts, and bolts. It is also important to ensure that all hardware is tightened to the proper torque specifications as listed in your owner’s manual. For included accessory hardware please refer to the default torque specifications provided below. Inspect all hardware after the first 30 miles to ensure proper torque specifications are maintained.

Bolt Size
M3 M4 M5 M6 M8 M10 M12

in-lbs
10.0 in-lbs 23.0 in-lbs 44.5 in-lbs 78.0 in-lbs

ft-lbs
3.5 ft-lbs 6.5 ft-lbs 13.5 ft-lbs 30.0 ft-lbs 52.0 ft-lbs

Nm
1.0 Nm 2.5 Nm 5.0 Nm 9.0 Nm 18.0 Nm 41.0 Nm 71.0 Nm

Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc. Remember, the length of a screw or bolt is measured from the start of the “mounting surface” to the end of the screw, so only include the screw head when measuring countersunk screws.

0 mm

10

20

30

40

50

60

70

80

90

0in

1

2

3

(d)

(c)

Kit Contents
(a) Headlight Bracket (LAH.23.11000-01)……………………………..Qty 1 (b) Adhesive Foam Tape…………………………………………………..Qty 1 (c) Headlight Harness (DNL.WHS.26000)……………………………..Qty 1 (d) D14 DOT Headlight……………………………………………………Qty 1

Tools Required
(a) Allen Key Set (b) Torx Bit Set (c) Phillips screw Driver (d) 12mm Socket or Wrench

1. Disassembly

DENALIELECTRONICS.COM

1.1 – Remove The Headlight Bezel
Step One: Remove the single philips head screw, located at the bottom of the light, that holds the headlight bezel to the bike.
Step Two: The bezel is held in by a clip at the top. Pull the bezel forward to remove it from the bike.

1.2 – Remove Headlight
Step One: Remove the three allen key screws that hold the light to the bike and remove the headlight.
Step Two: Disconnect the factory wiring harness from the 5 pin connector.
Note: The headlight is held in tension by 3 springs over each of the three mounting screws, remove these and keep these safe as they will be needed for installation.

2. Intalling The Headlight Harness

DENALIELECTRONICS.COM

To Battery


  • 2.1- Install The DENALI Headlight Harness
    Step One: Install The DENALI headlight wiring harness by running the power leads to the battery. Then plug the 4 pin headlight connector into the factory headlight harness.

Relays D-14 Headlight Connectors
To OEM Headlight Connector

3.1 – Attach Headlight To Bracket
Step One: Install The DENALI headlight into the bracket using the hardware supplied in with the headlight. Fasten the bracket to the upper mounting hole on the headlight.

3. Intalling The Headlight & Bracket

DENALIELECTRONICS.COM

3.2- Install The DENALI Headlight
Step One: Plug the new DENALI headlight into the wiring harness. (it does not matter which plug, one connector will remain capped)
Step Two: Using the factory hardware and springs, install the DENALI headlight and bracket as shown.

3.3 – Re-Install the Headlight Trim Ring
Step One: Install the included adhesive foam tape to the inside of the trim ring, so that it sits against the top light mounting bolt.
Step Two: Re-install the headlight trim ring.

Mounting Loacation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DENALI User Manuals

Related Manuals