KLARSTEIN 10034643 Iceblock Prosmart Air Conditioner Instruction Manual

www.klarstein.com

ICEBLOCK PROSMART
**Air Conditioner
10034643 10034645

**

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for
damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10034643

TECHNICAL DATA

SAFETY INSTRUCTIONS

General Safety Instructions

• The air conditioner is only suitable for indoor use and not for other applications.
• Follow the local mains connection regulations when installing the air conditioner. Make sure it is properly grounded. If you have questions about the electrical installation, follow the manufacturer’s instructions. Hire a trained electrician if necessary.
• Make sure that the power plug is intact and firmly plugged in after the air conditioner is installed. Install the power cord properly to prevent someone from stumbling over or accidentally pulling out the plug.
• Do not place objects in the air inlet or outlet. Keep the air inlet opening free of objects.
• If the drain lines are installed, make sure that the lines are connected properly and are not twisted or kinked.
• While adjusting the upper and lower air vents of the air outlet, gently pull them with your hands to prevent damage.
• Make sure the unit is upright when moving it.
• Do not disassemble the device. Do not modify or adjust the device on your own, otherwise, it may malfunction or even damage people and property. Contact the manufacturer or service personnel for a repair to prevent any dangers of malfunction.
• Do not pull the plug out to turn off the power.
• To prevent spillage of water or other liquids on the unit, do not place cups or other objects on the case .
• Do not use insect sprays or flammable substances near the air conditioner.
• Do not clean the device with chemical solvents such as gasoline or alcohol. When cleaning the air conditioner, disconnect the power cord. Clean the device with a damp soft cloth. If the unit is heavily contaminated, rub it with a mild detergent.
• The air conditioner may be used by children 8 years and older and persons with physical or mental disability or limited perception if they have been instructed in the safe use of the device and have understood the hazards involved.
• Children must not play with the device.
• Cleaning and maintenance must not be carried out by children without supervision.

Instructions on location

• Place the unit in a shallow, dry place. Keep a distance of more than 50 cm between the unit and surrounding objects and the wall.
• Keep the unit away from fuel, flammable gases, stoves, and other sources of heat.
• Do not place the appliance in a bathroom, laundry room, or other humid environments.
• The appliance must be installed in a room with a minimum size of 12 m 2 (Item 10034643) or 15 m 2 (Item 10034645) respectively.

DEVICE DESCRIPTION

Scope of supply

• Main Air conditioner Unit
• Hot air exhaust hose
• Hose Connector (Window end)
• Hose Connector (Air conditioner end)
• Window Kit
• Remote Controller

After unpacking, please check whether the above-mentioned accessories are included!

Control panel

Remote control

| 1 On/off
2 Panning movement on / off
3 Sleep mode
4 Speed level
5 Temperature up
6 Temperature down
7 Mode
8 Timer
Do not drop the remote control.
Do not place the remote control in a location exposed to direct sunlight.
---|---

INSTALLATION

1. Installation of the air conditioner
   • Place the device on a flat surface with a minimum distance of 30 cm to all sides of the device. Do not block the ventilation openings.
   • Do not use the device primarily as a dehumidifier.
   • Wiring must comply with local electrical safety regulations.

2. Installation of the exhaust hose

Temporary installation

1. Attach both ends of the exhaust hose to the square fixing clip and flat fixing clip.
2.  Insert the square fixing clip into the opening on the back of the fan.
3. Place the other end of the exhaust hose on a nearby sill.

Installation of the window slider set (not included/separately available)
Sash sets are usually installed horizontally and vertically. Check the minimum and maximum window sizes as shown in the figure below.

Function of the inner water tank
The inner water tank has a safety function that controls the water level. When the water level reaches a certain level, an indicator will light up to indicate that the water tank is full (If the water pump is damaged when the water tank is full, remove the rubber plug on the bottom of the unit to drain all water.)

GETTING STARTED

1. Select a location where there is a power connection nearby.

2. Install the exhaust hose as shown in the two illustrations below and adjust the position of the window.

3. Connect the exhaust hose as shown in the illustration with the exhaust hose (see figure below) (only for models with integrated heater).

4. Plug the mains plug into a grounded AC 220 – 240 V~ (50/60 Hz) socket.

5. Press the power button to turn on the device.

OPERATION

Before getting started Temperature range

| Maximum cooling| Minimum cooling
---|---|---
DB/WB(°C)| 35/24| 18-Dec

Make sure that the exhaust hose is correctly installed. Safety instructions for cooling and dehumidification:

• When using the cooling and dehumidifying functions, wait at least 3 minutes after turning off the power before turning the power on again.
• Make sure the power supply meets the requirements.
• Use an AC connection.
• Only use the socket for this device and make sure that no other devices are connected to this circuit

Auto mode
Based on the current room temperature, the mode is automatically selected: cooling, air humidification or heating (see table).

Cooling

• Press the Mode button until the cooling symbol appears on the screen.
• To select the desired temperature (16 °C – 31 °C), press the up or down buttons.
• Press the Speed button to select the fan speed.

Dehumidification

• Press the Mode button until the dehumidification icon appears on the screen.
• The temperature is automatically set to 2 ° C less than the room temperature.
• The speed of the fan motor is automatically set to low.

Fa

• Press the Mode button until the fan symbol appears on the screen.
• Press the Speed button to select the fan speed.

Timer operation
Automatic switch-on time:

• When the unit is off, press the TIMER button and select the desired on-time.
• ‘Preset ON Time’ will be displayed on the screen.
• The switch-on time can be selected as desired (00:00 – 24:00).

Automatic switch-off time

• When the unit is turned on, press the TIMER button and select the desired off time.
• ‘Preset OFF Time’ will be displayed on the screen.
• The switch-off time can be selected as desired (00:00 – 24:00).

Panning movement

• Press this button after turning on the unit. The device will then move automatically from left to right.
• If you press the button again, the movement will be stopped and the ventilation grille of the device will remain in this position.

Snooze

• Press the Sleep button to set the temperature when the unit is in cooling mode. After one hour the temperature will be raised by 1 ° C. After 2 hours the  temperature will be raised by 2 ° C.
• Press the Sleep button to set the temperature when the appliance is in heating mode. After one hour, the temperature will be lowered by 1 ° C. After 2 hours the temperature will be lowered by 2 ° C.
• Press the button again to cancel the setting.

Continuous drainage

If you plan to leave this unit unused for a long time, remove the rubber plug from the drain hole at the bottom of the unit and drain all the water outside the device.
You can use continuous drainage with a drainage hose connected to the lower drain opening when the unit is being used in heating mode.
Continuous drainage does not need to be used when operating the unit in cooling or dehumidifying mode. The device can automatically evaporate the water condensation through the spray motor. Make sure that the drainage holes are well drilled.
If the water spray motor is damaged, continuous drainage can be used. Connect the drain hose to the lower drain opening. If the spray motor is damaged, intermittent drainage can also be used. If, under these conditions, the water indicator lights up completely, please connect a drain hose to the lower drain opening so that all the water in the water tank will be drained outside the device. That way the device can also work well.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via your smartphone, but also gives you access to recipes and additional information.

Follow these steps to connect your smartphone to your Klarstein device:

1. Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
2. Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
3. Open the Klarstein app.
4. Sign in to your account. If you do not have an account, sign up in the Klarstein app.
5. Follow the instructions from the app.

App Download
Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.

Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

https://play.google.com/store/apps/details?id=com.chaltec.klarsteinrn&hl=en

Troubleshooting connection problems

If your Klarstein device cannot be found in the WLAN, check the following:

• Is the device plugged in?
• Is the WiFi feature of my phone enabled?
• Is the WiFi function of the Klarstein device activated? (Follow the instructions in the app)
• Has the WLAN password been entered correctly?
• Are the router, Klarstein device and smartphone in the immediate vicinity during the connection attempt? (Ideally no more than 5 m apart)
• If you have deactivated the 2.4 GHz band in the settings of your wireless router, activate it in your router settings.

Note: For further help, follow the instructions in the app when setting up the connection.

CLEANING AND CARE

• Switch off the device before cleaning and disconnect the power plug from the socket.
• Do not use gasoline or other chemicals to clean the unit.
• Do not wash the device directly.
• Contact the after-sales service if the unit is damaged.

Cleaning the air filter

• The air filter may be blocked by dust / protection and should be cleaned once every two weeks.
• Open the ventilation grille and remove the air filter.
• Clean the air filter with a neutral detergent and lukewarm water. Then dry the filter in the shade.
• Replace the air filter and all other components.

Cleaning the device surface
Clean the surface of the device with a neutral detergent and a damp cloth. Then rub the surface of the device dry with a dry cloth.

TROUBLESHOOTING

The unit does not start when the
On / Off button  is pressed.| The water level indicator light is flashing because the water tank is full.| Empty the water from the water tank.
The room temperature is higher than the set temperature (electric heating mode).| Reset the temperature setting.
The room temperature is lower than the set temperature (cooling mode).| Reset the temperature setting.
The device is not cooling properly.| The doors or windows have not been properly closed.| Make sure all doors and windows are closed.
There are heat sources in the room. The exhaust hose has not been con- nected or is blocked.| If possible, remove the heat sources. Connect or clean the hose.
The temperature set- ting is too high.| Reset the temperature setting.
The air intake is blocked.| Clean the air intake.
The device is very loud.| The floor of the installation site is not flat or not flat enough.| If possible, place the unit on a flat, level surface.
The noise is caused by the refrigerant circulating inside the fan.| This is normal.
Code E 0| The room temperature sensor is defective.| Replace the room tempera- lure sensor (the device also works without the room temperature sensor being intact).
Code E 1| Condenser temperature sensor is defective.| Replace the condenser temperature sensor.
Code E 2| When cooling, the water tank is full.| Remove the rubber stopper and empty the water.
Code E 3| The evaporator temperature sensor is defective.| Replace the evaporafor temperature sensor.
Code E 4| When heating, the water tank is full.| Empty the water tank.

Notes on Refrigerant R290

Warning

• The air conditioner must be kept and transported upright. Otherwise, irreparable compressor damage may occur. Let the unit sit for at least 24 hours before using it.
• Switch off the device and disconnect it from the power supply before cleaning.
• Make sure that the product generates a constant flow of air. Make sure the air inlets and outlets are not blocked.
• To prevent leaks, operate this unit on a horizontal surface.
• Any person working on a refrigerant circuit should have a current certificate from an accredited assessment body. This ensures competence for the safe handling of refrigerants according to an industry-recognised assessment specification.
• If the device stops working, dispose of it properly.
• Store the device in a well-ventilated place when not in use.
• Store the device so that it is not damaged.
• Repairs may only be carried out by the manufacturer or an authorised specialist company.
• The cables connected to the device may contain potential ignition sources.
• Do not damage any components of the refrigerant circuit. Escaping refrigerant may not be noticed because it is odourless.
• Maintenance and repairs must be carried out under the supervision of specialists in the use of flammable refrigerants.

Information for rooms with refrigerant pipes

• Limit the piping to a minimum.
• Be careful not to damage the piping.
• Appliances with flammable refrigerants may only be installed in a well-ventilated room.
• Comply with national gas regulations.
• All mechanical connections must be freely accessible for maintenance purposes.

Information for rooms with refrigerant pipes

• Limit the piping to a minimum.
• Be careful not to damage the piping.
• Appliances with flammable refrigerants may only be installed in a well-ventilated room.
• Comply with national gas regulations.
• All mechanical connections must be freely accessible for maintenance purposes.

DANGER
Fire hazard !
This device contains the flammable refrigerant R290. If the refrigerant escapes and is exposed to an external ignition source, there is a risk of fire.

PRODUCT DATA SHEET

Information according to regulation (EU) No. 626/2011

Supplier‘s trademark: Klarstein
Supplier‘s model identifier: 10034643
Inside sound power levels at standard rating conditions on cooling mode in dB: 65 dB

Refrigerant (R290) leakage contributes to climate change. Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a refrigerant with higher GWP, if leaked to the atmosphere. This appliance contains a refrigerant fluid with a GWP equal to 3. This means that if 1 kg of this refrigerant fluid would be leaked to the atmosphere, the impact on global warming would be 3 times higher than 1 kg of CO2 , over a period of 100 years. Never try to interfere with the refrigerant circuit yourself or disassemble the product yourself and always ask a professional.

Energy efficiency ratio (EERrated ): 2,6
Energy efficiency class: A

Energy consumption 1,0 kWh per 60 minutes, based on standard test results. Actual energy consumption will depend on how the appliance is used and where it is located.
Cooling capacity Prated in kW: 2,6 kW

Information according to regulation (EU) No. 206/2012

Electricity consumption of single/double duct appliances
(indicate for cooling and heating separately)| DD: QDD
SD: QSD| 1,0| DD: kWh/a
SD: kWh/h
Sound power level| LWA| 65| dB(A)
Global warming potential| GWP| 3| kgCO3 eq.
Contact details for obtaining more information| Chal-Tec GmbH, Wallstrane 16, 10179 Berlin, Germany.

Information according to regulation (EU) No. 626/2011

Supplier‘s trademark: Klarstein
Supplier‘s model identifier: 10034645
Inside sound power levels at standard rating conditions on cooling mode in dB: 65 dB

Refrigerant (R290) leakage contributes to climate change. Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a refrigerant with higher GWP, if leaked to the atmosphere. This appliance contains a refrigerant fluid with a GWP equal to 3. This means that if 1 kg of this refrigerant fluid would be leaked to the atmosphere, the impact on global warming would be 3 times higher than 1 kg of CO2 , over a period of 100 years. Never try to interfere with the refrigerant circuit yourself or disassemble the product yourself and always ask a professional.

Energy efficiency ratio (EERrated ): 2,6
Energy efficiency class: A

Energy consumption 1,0 kWh per 60 minutes, based on standard test results. Actual energy consumption will depend on how the appliance is used and where it is located.
Cooling capacity Prated in kW: 2,1 kW

Information according to regulation (EU) No. 206/2012

Model identifier(s)| 10034645|
---|---|---
Description| Symbol| Value| Unit
Rated capacity for cooling| Prated for cooling| 3,5| kW
Rated capacity for heating| Prated for heating| | kW
Rated power input for cooling| PEER| 1,4| kW
Rated power input for heating| PCOP| –| kW
Rated Energy efficiency ratio| EERd| 2,6| –
Rated Coefficient of performance| COPd| –| –
Power consumption in thermostat-off mode| PTO| –| W
Power consumption in standby mode| PSB| 0,5| W
Electricity consumption of single/double duct appliances
(indicate for cooling and heating separately)| DD: QDD
SD: QSD| 1,4| DD: kWh/a
SD: kWh/h
Sound power level| LWA| 65| dB(A)
Global warming potential| GWP| 3| kgCO2 eq.
Contact details for obtaining more information| Chal-Tec GmbH, Wallstrane 16, 10179 Berlin, Germany.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.
This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

DECLARATION OF CONFORMITY

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.

Importer for Great Britain:
Berlin Brands Group UK Ltd
PO Box 1145
Oxford, OX1 9UW
United Kingdom
Hereby, Chal-Tec GmbH declares that the radio equipment type Metrobreeze Rom Smart is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address:use.berlin/10034643

For Great Britain:
Hereby, Chal-Tec GmbH declares that the radio equipment type Metrobreeze Rom Smart is in compliance with the relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address:use.berlin/10034643

References

• Klarstein | Your home. Your kitchen. Your style.
• Take-e-way GmbH | take-e-back | Elektroschrott Rücknahmesystem Onlinehandel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>