GYS 059962 Cordless Foldable Under Bonnet LED Lamp User Manual

059962 Cordless Foldable Under Bonnet LED Lamp
**User Manual

**

LAMPE SOUS CAPOT 600L
UNDER BONNET LAMP 600L
Translation of the original instructions

FEATURES

1. ON/OFF Power Button
2. Charging Port
3. Grip Clamp with Extension & Retraction Spring
4. Folding Joint
5. SMD White LED
6. Charging Status LED
7. AC Charging Adaptor (Home Charger)
8. DC Charging Adaptor (Car Charger)
9. Barrel (Cylindrical) Connector

UNDER BONNET LAMP 600L

3. Grip Clamp with Extension & Retraction Spring
4. Folding Joint

SAFETY WARNINGS AND INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USE
Warning: Read and understand all instructions in this manual prior to operating this product. Failure to follow all of the instructions listed in this manual may result in electric shock, fire, and/or serious injury/death.

SAFETY DEFINITIONS AND GUIDELINES

Warning: A statement that indicates impending danger, or a potentially hazardous condition which, if not avoided, could result in serious injury or death to the operator and/or bystanders.
Caution: A statement that indicates impending danger, or a potentially hazardous condition that, if not avoided, could result in minor or moderate injury to the operator and/or property damage.

SAFETY INSTRUCTIONS

Warning:

• The unit is not waterproof. DO NOT use this product under water or immerse in water.
• To protect against electrical hazards, do not immerse chargers, adapters or units in water or other liquid.
• Do not use this unit for applications other than its intended uses.
• Charge indoor only.
• Do not expose the internal battery to fire or severe heat; it may explode.
• Do not place or store this item where it can fall, or be pulled into a tub or sink.
• Do not clean this product with a water spray gun or the like.
• Close supervision is necessary when this product is used near children.
• Use only attachments recommended or sold by the manufacturer.
• Use only the chargers that are provided with this product to charge the internal battery.
• Do not operate this product if it has been subjected to a sharp blow, dropped, or otherwise damaged in any shape or form. Take the unit to a qualified service person for inspection.

Caution:

• Never look directly into the light or shine the light into another person’s eyes when it is illuminated.
• Charge the lamp with the chargers that are provided with the product. Plug in the charging adaptor into the unit first, then plug into the charging source.
• Do not cut, pull, or expose the charging adaptors/power cords to extreme heat.
• Do not disassemble the housing. There is no internal serviceable part.
• Pull by the adaptor plug rather than the cord when disconnecting the charging adaptor.
• This unit contains rechargeable batteries. Although the lamp arrives partially charged from the factory, it MUST be fully charged before the first use.
• Recharge the unit after each use, or every 6 months to prevent the battery charge from depleting.
• Place the charging adaptor cord so that it does not become entangled or become a safety hazard.
• Do not attempt to charge the product if the charging adaptor or power cable is damaged. Contact the manufacturer for the replacement.
• Keep the charging adaptor cord and power cable away from sharp corners.

CHARGING AND RECHARGING THE INTERNAL BATTERY

This product has been shipped partially charged. Charge the unit right out of the box and before the first use with the AC Wall Charger for 10-12 hours. Recharge the unit after each use.
IMPORTANT: The internal battery must be charged after each use and every 6 months, even when the unit is not in use.
Charging and Recharging using AC Wall Charger (Home Charger )

1. Ensure all the power switches are OFF.
2. Insert the barrel (cylindrical) connector (9) of the AC Wall Charger (7) into the Charging Port (2) of the lamp.
3. Plug the male prongs of the AC Wall Charger (7) to an AC wall outlet. The Battery Charging Status Indicator LED (6) on the unit will illuminate.
4. Recharge the unit until the Full Charge Status LED (6) illuminates GREEN.

Charging and Recharging using 12 Volt DC Charging Adaptor (Car Charger)

1. Ensure all the power switches are OFF.

2. Insert the barrel (cylindrical) connector (9) of the 12 Volt DC Car Charger (8) into the Charging Port (2) of the
   lamp.

3. Insert the 12 Volt DC plug into the 12 Volt DC power source. The Battery Charging Status Indicator LED (6) on the unit will illuminate.

4. Recharge the unit until the Full Charge Status LED (6) illuminates GREEN.

IMPORTANT: Some vehicles require the ignition to be turned ON in order to power up the cigarette lighter socket, or the accessory outlet.
Notice: When the lamp is undercharged, the light will NOT function and it will be immediately turned OFF upon connecting to the AC or DC charger.

OPERATING INSTRUCTIONS

Worklight – High and Low beam intensity:
Press the Power ON/OFF Button (1) once, and the LOW BEAM INTENSITY mode with 120 LEDs will illuminate.
Press the Power ON/OFF Button (1) twice, the HIGH BEAM INTENSITY mode will illuminate.
Press the Power ON/OFF Button (1) three times, the WORKLIGHT will turn OFF..

TO UNFOLD THE WORK LIGHT FOR A FLAT MODE OPERATION

1. Firmly hold both clamps (3).
2. Swing open both sections of the Worklight casing all the way to a flat position.
3. Continue to apply force beyond the initial resistance to hear a “CLICK”, locking both sections of the Worklight in a flat position.
4. Both clamps (3) are spring-loaded and can be extended or retracted for the light desired length.

ATTACHING THE LAMP TO THE WORKPLACE

1. Firmly Attach one of the clamps (3) to the intended surface.
2. Extend the other clamp (3) to adjust the light for the desired length.
3. Firmly mount the second clamp to the other part of the workspace.

CARE AND MAINTENANCE

1. After use and before performing maintenance, unplug and disconnect the lamp from the charger.
2. Make sure all of the lamp components are in place and are in good working condition.
3. Wipe the unit with mild soap and a lint-free wet cloth. Make certain to dry the unit entirely before storing it for future use.
4. DO NOT disassemble the housing. There are no serviceable parts.
5. All rechargeable batteries discharge over time, and more rapidly at elevated and/or low temperatures. When the unit is not in use, the internal battery shall be charged every 6 months.
6. SAFE BATTERY DISPOSAL – This product contains maintenance-free, sealed, non-spillable battery, which must be disposed of properly; recycling is required. Contact your local authority for disposal information. Failure to comply with local, state and federal regulations can result in fines and/or imprisonment.

CONTACT YOUR LOCAL WASTE MANAGEMENT AUTHORITY TO DISPOSE OF THIS PRODUCT.

TROUBLESHOOTING

A. If the Product Does Not Operate

1. The internal battery may have been completely discharged – Charge the unit completely, following the previous charging instructions.

B.Worklight Does Not Operat e

1. Check that the unit is fully charged. Recharge the lamp’s internal battery if necessary.
2. Make certain that the ON/OFF Power Button is firmly pressed to set the unit to the ON position.*

C.The lamp does not charge

1. Check connection to the provided AC Charging Adaptor (Home Charger).
2. Check connection to the 12 Volt DC Charging Adaptor (Car Charger).
3. Check if there is power through the AC outlet or 12 VDC socket.

SPECIFICATIONS

Internal Rechargeable Battery: 3.7 Volt 4000 mAh Lithium-ion
1000 Lumens SMD – High-Intensity Mode: 1000 Lumens
500 Lumens SMD – Low-Intensity Mode: 500 Lumens
White SMD: 120 LEDs
Low-Intensity Mode Runtime: 8 Hours
High-Intensity Mode Runtime : 4 Hours
Product Dimensions (extended): 11 x 10 x 133 cm
Product Weight: 1,7 kgs

WARRANTY
The warranty covers faulty workmanship for 2 years from the date of purchase (parts and labor).
The warranty does not cover:

• Transit damage.
• Normal wear of parts (eg. : cables, clamps, etc..).
• Damages due to misuse (power supply error, dropping off equipment, disassembling).
• Environment-related failures (pollution, rust, dust).

In case of failure, return the unit to your distributor together with:
– The proof of purchase (receipt etc …)
– A description of the fault reported

UNDER BONNET LAMP 600L

PICTOGRAMS

| The device complies with European Directive. The certificate of compliance is available on our website
---|---
| Equipment in compliance with British requirements. The British Declaration of Conformity is available on our website (see home page)
| Equipment in conformity with Moroccan standards. The declaration Cم (CMIM) of conformity is available on our website (see cover page)
| Waste Electrical and Electronic Equipment, separate waste collection required, Do not throw in a domestic bin
| The recyclable product that falls within waste sorting recommendations (according to Decree n° 2014-1577).

Société JBDC
1, rue de la Croix des Landes
CS 54159
53941 SAINT-BERTHEVIN Cedex

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>