SUNSKY WD-200 Wireless Charging Clock Speaker User Guide

SUNSKY WD-200 Wireless Charging Clock Speaker

Notice to User

• Please make sure to use a fast-charging plug to power the device. (Charging plug not included).
• This device can only charge mobile phones that have a standard wireless charging function.
• Wearing a metal phone case or a phone case that is too thick will block the wireless charging transmission. Please remove the phone case when wireless charging your mobile phone.
• There may be signal interference and an increase in noise in FM radio mode when the wireless charge function is being used at the same time.
• When using FM radio mode, please plug in the provided AUX cable to the AUX jack on the device. The cable acts as an external antenna for radio reception. You can adjust the position of the cable to maximize the radio reception.
• When the device is in clock mode, the 【Ö 】 button will not function. Press the 【M】 button to fully wake the device first then press the 【M】button to switch modes.
• For safety reasons, the device’s wireless charging function may temporarily stop when overheating is detected during the wireless charging process.
• lf you want to use Bluetooth and wireless charging at the same time, please make sure the device is fully turned on and switched to Bluetooth mode.

Safety Instructions

Please read the following instructions. Failure to follow all the instructions listed below may damage the device and/or may result in electric shock, fire and/or personal injury.]

• Do not expose the device to direct sunlight
• Do not remove screws from or open the device casing by yourself
• To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
• The unit shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the unit.
• Never charge the device with a damaged power cable.
• Never put the device or charging cable near heat registers, radiators, stoves or heaters.
• Always put the device where it is not easily knocked over by persons in households or businesses.
• Never touch the device with wet hands.
• This device is only for the intended household or indoor use.
• Never use any detergents to clean any part of the unit.

Welcome
We would like to congratulate you on the purchase of your WD-200 Wireless Charge Clock Speaker. Please read this manual carefully before use.

What’s Included
WD-200 device x1, USB Type-C power cable x1, Aux Cable x1, User guide x 1

Overview

Button Functions

1. Power Button：
   Press & Hold： Power On/Off Short Press after device turned on： Switch between Clock Mode & Working Mode

2. M Mode/Bass Button： Short press： Switch modes Press & Hold： Bass Adjust (BT/FM/Card Mode)

3. Clock Button：
   Short Press： Set Alarm/Confirm Press & Hold： Alarm On/Off
   Press Twice： Set Time

4. Next Button：
   Short press：
   Next Track(BT/TF Card mode)/ Next Channel (FM Radio)/ Add Hours/Minutes (Clock Mode)/ 5 minutes SNOOZE(When alarm buzzes) Press & Hold： Volume /Bass up

5. Previous Button：
   Short press： Previous Track(BT/TF Card mode)/Previous Channel(FM Radio)/Minus Hours/Minutes (Clock Mode)/Alarm Dismiss (When alarm buzzes) Press & Hold： Volume /Bass down

6. button： Short press：
   Play/Pause(BT pairing mode, TF mode)/Answer/End a call(Incoming Call)/Mute(FM Radio/Aux in mode)/Confirm (Clock Mode)/
   Alarm Dismiss (When alarm buzzes) Press & Hold：
   Reject an incoming call (incoming call) Press & Hold 4 seconds： Disconnect devices(BT pairing mode)

Operation

• Charging the device
This device has a built-in rechargeable battery. To charge the device, use the provided USB Type-C Cable, connect the Type-C connector to the Type-C Input on the device, and the Standard USB-A Connector to a fast-charging plug/Adaptor (Not Included)*. The red charging led indicator illuminates when charging and turns off when charging is complete. The wireless charge function requires a power connection to the charging plug.

Wireless Charge your mobile device
Connection to a fast charging plug is required to power the wireless charging function. The connection procedures are the same as how the device is connected for charging (Please see the steps above).

• NOTE 1: After the power is connected, Place your mobile phone on the phone stand of the powered WD-200 to wireless charge your phone. If charging is not stable, adjust the phone to make sure its back is touching the wireless charge area on the device.

• NOTE 2: The wireless charge indicator lights up when charging. Some phone cases may affect or block the wireless charging transmission, remove the case if necessary.
  The wireless charge-led indicator blinks if metals are detected indicating there is an abnormal situation. Remove any metals on the device to prevent overheating.

• NOTE 3: 10W/7.5W wireless charge output require the device to be connected to a 9V-2A QC 3.0/PD fast charging plug. Connecting the device to a 5V-3A charging plug can only provide 5W wireless charging output. Using a non-qualified pwoer plug may result in malfunctioing of the device.

• NOTE 4: The charging plug may not provide sufficient power if the wireless charging function, speaker function and USB charge out function are all used at the same time. In such situation, removing the USB connection is recommended.

Power On/Off & Switch modes
Press and hold the 【Ö】button to turn on the speaker. Short press the 【Ö 】button to switch modes. Short press the 【M】button to enter clock mode. Short press the【Ö 】button in clock mode to switch on the device for other modes.

Bluetooth Pairing
Press the【M】 button repeatedly to enter Pairing mode. The word “BLUE” will start blinking on the speaker indicating that it is waiting for the device to pair. On your Bluetooth device, find and select “WD-200 / WD-200A” under your Bluetooth device listing to pair. A successful connection via Bluetooth will be followed by an audible notification. For help with Bluetooth Settings, please consult your device’s user manual.

Handsfree Speakerphone
The hands-free speakerphone function is enabled when the device is paired with your mobile device. Press the 【 PLAY】 button to answer an incoming call. To decline a call without answering, press and hold the 【 PLAY】button during an incoming call. To end a call, press the 【 PLAY 】button during a call. For the best conversation experience, make sure the WD-200 unit is placed near (within 40cm) the user.

FM Radio

Press the【 M】 button repeatedly to enter FM radio mode. Press and hold the【PLAY 】button to initiate the automatic channel search. Searched channels will be saved automatically. Press the【-】or【+】 button to switch channels. Short press the【 PLAY】button to mute the speaker when listening to the radio and short press the button again to unmute.

NOTE: When using FM Radio mode, please plug in the provided AUX cable to the AUX jack on the device. The cable acts as an external antenna for radio reception. You can adjust the position of the cable for better radio reception.

NOTE: Please note that FM signal can be weakened MUCH depending on the type of building you are in. (For example, It can be hard to catch proper signal when being in a concrete building or basements.)
NOTE: There may be signal interference and an increase in noise in FM radio mode when the wireless charge function is being used at the same time.

TF Card
Insert a TF card to enter TF card mode or press the the【M】button to switch to TF card mode if card is already inserted Press the【-】or 【+】button to select music from the card. Press the【PLAY 】knob to play/pause music.

Auxiliary Connectin (AUX)
Use the provided AUX cable, connect one end to the AUX Out jack of your audio source device and the other end to the AUX-In jack on the WD-200 device. Press the the【M】button to switch to AUX mode. Press the 【PLAY 】button to mute/unmute the speaker.

Setting the clock
This device can automatically synchronize the time on some mobile phone models after it is connected with the phone through Bluetooth.
It requires your phone to support this function in order to synchronize the time. If the time on the device is not updated after it is connected to the phone through Bluetooth, then you may need to set the time manually through the following procedures:

Press the【TIMER】button twice quickly to set the time. Press the【-】 【+】button to set the hour then press the the【TIMER 】button or the 【PLAY】button to conrm. Now press the the【-】【+】button to set the minute and press the the【TIMER】button the 【PLAY】button to confirm.

Setting the alarm
Short press the the【TIMER】button once to set the alarm. Press the 【-】【+】button to set the hour then press the the【TIMER】button or the 【PLAY】button to confirm. Now press the the【-】【+】button or to set the minute and press the the【TIMER】button or the【PLAY】button to confirm. Once the alarm is set, a white dot next to the clock digits will appear indicating that an alarm has been set.

Snooze/Alarm Dimiss & Alarm On/Off
Press the【PLAY】button when the alarm buzzes to snooze for 5 minutes. Press any buttons (Except the On/Of button & the Snooze button) to dismiss the alarm when it buzzes. The alarm will still buzz on the next day. To disable the alarm completely, press and hold the 【TIMER】button, until the white dot next to the clock digits disappears.

Soothing Mode/ White noise mode

(Optional feature. Only available in WD-200A soothing mode version.) Press the the【M】button to switch to Soothing mode. Press the【-】 or 【+】button to select soothing sounds. Press the【PLAY】knob to play/pause the soothing sound. Soothing sound/music will automatically stops if the speaker has not been operated for 30 mins.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oF And on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Specifications

• BT version： V5.1
• Wireless Distance：≤10m
• Speaker Power：3W
• Speaker impedance：4Ω
• Charging output：5W/7.5W/10W
• Input voltage：5V-3A / 9V-2A
• Size：75.7×121.5×144 mm
• Battery Capacity：1200mAh

We produce quality products with our heart for our customers.
If you encounter any difficulty in using our product please feel free to contact us and we will sincerely serve every customer.
Contact information can be found from the online/offline store where you purchased this item.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>