Gude GHS 690 L Electric Hedge Trimmer Instruction Manual
- June 5, 2024
- Gude
Table of Contents
GHS 690 L Electric Hedge Trimmer
Instruction Manual
GHS 690 L Electric Hedge Trimmer
Translation of the original instructions
Please read the instructions carefully before starting the machine.
LIEFERUmFANG
|
---|---
Assembly
Operation 
Operation
Technical Data
Hedge trimmer ……………………………………….GHS 690 L
Art. No …………………………………………………………………………….. 93999
Service connection ……………………………..230 V~50 Hz
Motor output …………………………………………….. 710 w/P1
knife movement ……………………………………… 1700 min-1
knife Spacing …………………………………………………..24 mm
Cutting length ………………………………………………600 mm
beam length …………………………………………………690 mm
weight ………………………………………………………………..3,6 kg
Degree of protection ……………………………………….. IP 20
Protection class …………………………………………………………. II
Noise and Vibration Information
Sound pressure level LPA 1) ……………………………………….81 db (A)
Measured sound power level LwA 1) ………100,44 db (A)
Guaranteed sound power level LwA ……..102 db (A)
wear ear protectors!
Schwingungsemissonswert Vorderer Griff ah 2) ……5,094 m/s
2 Schwingungsemissonswert Hinterer Griff ah 2) ……3,854 m/s 2 1)
Uncertainty K= 3 db (A), 2)
Uncertainty K= 1,5 m/s 2
Warning: The vibration emission level will vary because of the ways in
which a power tool can be used and may increase above the level given in this
information sheet.
The vibration emission level may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
An accurate estimate of the vibratory load should also take into account the
times when the tool is shut down or when it is running but not actually in
use. This may significantly reduce the vibratory load over the total working
period.
Identify additional safety measures to protect the operator from the effects
of vibration such as maintaining the tool and the accessories, keeping the
hands warm, and organization of work patterns.
**** Read and understand the operating instructions before using the appliance. Abide by all the safety measures stated in the service manual. Act responsibly toward third parties.In case of any doubts about connection and operation refer please to our customer center
Power tool description
- Safety switch
- Front hands protection
- Knife/cutter bar
- eyelet wall mounting
- Knife/cutter bar protection
- cable strain relief
- Power supply cable
- ON/OFF switch
- rotary handle lock
Specified Conditions Of Use
The hedge trimmer is designed for trimming shrubs and hedges in private hobby
gardens
The device must not be used for crushing compost, as persons or damage to
property können.The hedge trimmer is designed for trimming shrubs and hedges
in private hobby gardens.
Do not use this product in any other way as stated for normal use. Not
observing general regulations in force and instructions from this manual does
not make the manufacturer liable for damages.
The charger may only be operated with a protective switch against stray
current (RCD max. stray current 30mA).
Requirements for operating staff
The operating staff must carefully read the Operating Instructions before
using the appliance.
Qualification: Apart from the detailed instructions by a professional, no
special qualification is necessary for appliance use. minimum age: Persons
over 18 years of age can
only work on the appliance. An exception includes youngsters trained in order
to reach knowledge under the supervision of the trainer during occupational
education.
Training: Using the appliance only requires corresponding training by a
professional or the Operating Instructions. No special training is necessary.
The operator is responsible for accidents or risks to third parties. Observe
to keep out of the dangerous zone
Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified
medical attendance as quickly as possible. Protect the injured person from
further harm and calm them down. For the sake of eventual accident, in
accordance with DIN 13164, a workplace has to be fitted with a first-aid kit.
It is essential to replace any used material in the
first-aid kit immediately after it has been used. If you seek help, state the
following pieces of information
- Accident site
- Accident type
- Number of injured persons
- Injury type(s)
Symbols
| **** | Caution! |
|---|---|
| **** | Read the Operating Instructions! |
| Take the battery always out before any work on the appliance. | |
| Cable pulling/transport prohibited | |
| In case of cable damage or nock, immediately pull out the plug from the |
socket
| Keep a distance from persons
Observe to keep out of the dangerous zone
| Protect against moisture
Never expose the tool to rain.
| wear eye protection!
wear ear protectors!
| wear protective gloves!
| wear safety cut-through resistant shoes with safety sole and steel toe!
| Portez une tenue de protection avec doublure contre perçage!
| Any damaged or disposed electric or electronic devices must be delivered to
appropriate collection centres.
| Protect against humidity
| This side up
General Power Tool Safety warnings
Warning
Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term „power tool“ in the warnings refers to your mains-operated (corded
power tool or battery-operated (cordless) power tool.
-
work area safety
a) Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks that may ignite dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. -
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (ground power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (protected supply. The use of an RCD reduces the risk of electric shock. -
Personal safety
a) Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards. -
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate at which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/ or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. -
Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Additional safety instructions
Hedge trimmer
- Keep parts of your body off the cutting blade. Do not remove jammed material while the blades are moving.
- when removing jammed material, make sure the appliance is off.
- Attach the knife protection for transport or storage. before you start with the work, search the thicket for hidden objects such as wire fences, etc.
- Do not let children, other persons, or pets near the cutting scissors.
- Do not use the cutting scissors if the cutting tool is not fitted properly or when it is damaged.
- before adjusting the cutting scissors, make sure the knives or blades do not touch stones or debris.
- Do not cut any hard objects. This could lead to accidents and damage to the cutting scissors.
- Avoid abnormal posture and do not work above shoulder height.
- Respect the system voltage!
- Do not attempt to remove shavings when the knives are moving. when removing any jammed material, make sure the cutting scissors are off and stopped. when lifting or holding the cutting scissors, do not hold the cutting knives.
CAUTION: Knives are still running for a short time after being switched
off.
Putting into operation for your safety
Before carrying out any work on the machine, disconnect the plug from the
socket. bei unbeabsichtigtem betätigen des Ein-/Ausschalters besteht
Verletzungsgefahr.
Maintenance
** Before carrying out any work on the machine, disconnect the plug from
the socket. before using the appliance, perform a visual inspection at all
times to make sure the power cord and the plug, in particular, are not damaged
on the charger.
The machine must not be used under any circumstances if the machine or the
safety devices are damaged. If the device is defective, the repair has to be
made exclusively by customer service. Use only original accessories and
original spare parts.
Only a regularly maintained and treated appliance can serve as a satisfactory
aid. Insufficient maintenance and care can lead to unforeseen accidents and
injuries.
The guarantee
The warranty period of 12 months applies to commercial use and 24 months
applies to private use and commences on the day of purchase of the device.
The guarantee solely covers inadequacies caused by material defects or
manufacturing defects. An original payment voucher with the date of the sale
needs to be submitted for any claim in the guarantee period.
The guarantee does not cover any unauthorized use such as appliance
overloading, use of violence, or damage as a result of any unauthorized
interference or caused by foreign items. Failing to follow the operating and
assembly instructions and common wear are.
Service**
Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? we will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No.,product No. and year of production. All this data can be found on the type label. Please enter here for future reference
Serial No.:………………….
Art. No:…………………….
Year of production:……………….
Tel.:+49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com
Disposal
Note to the disposal arising from icons placed on the appliance or on the
package. A description of the meanings can be found in the section “Marking”.
** Do not dispose of electrical appliances in the household waste.
According to European Directive 2002/96/EC on waste electrical and electronic
equipment and transposition to the national law, worn electrical equipment
must be collected separately and put to recycling.
Recycling alternative to the return requirement:
As an alternative to recycling, the owner of the electrical equipment is
obliged to provide assistance in professional recycling. For this purpose, an
old appliance can be put to a collection center that will dispose of it in
accordance with the national circulation management and the waste Act.
This does not apply to accessories connected to old appliances and auxiliary
equipment without electrical components.
Transport packaging disposal**
The packaging protects the appliance against damage during transport.
Packaging materials are usually chosen according to environmental friendliness
and waste treatment aspects and can therefore be recycled. Returning the
packaging to material circulation saves raw materials and reduces waste. Parts
of packaging (e.g. foils, styrofoam ®) can be dangerous to children. Risk of
suffocation! Keep the packaging out of reach of children and dispose of them
as quickly as possible.
Inspection and maintenance plan
Generally| Knife/cutter bar protection| Regularly clean the outer part
Let regularly checked by an authorized workshop
Check for cracks and fissures
Let regularly sharpen
---|---|---
Before any start-up| Knife/cutter bar protection| Functional test
Functional test
After every take-out of service| ON/OFF switch
Power supply cable| Use Knife/cutter bar protection
storage| whole appliance
Plastic body
Knife/cutter bar| To be cleaned and the knife bar slightly lubricated.
To be safely stored in a cold room. Has it been checked in a specialized
workshop?
Failures – Causes – Removal
| Failures | Causes | Removal |
|---|---|---|
| Cutting scissors not working. | broken cable |
Appliance is defective
Internal cables are defective| Consult with the customer service center
Consult with the customer service center
Consult with the customer service center
Unsteady running, strong vibrations| Appliance is defective| Consult with the
customer service center
EC-DECLARATION OF CONFORMITY
We, hereby declare the conception and construction of the below-mentioned
appliances correspond – at the type of construction being launched – to the
appropriate basic safety
and hygienic requirements of EC Directives. In case of any change to the
appliance not discussed with us the Declaration expires.
Article-No…………………………..
………………………….. / 93999 hedge trimmer GHS 660 D
…………………………… /
……………………/
…………………/
Appropriate EU Directive……………….
2006/95/EC…………………………..
2009/105/EC……………………..
2011/65/EC ROHS…………………..
89/686/EEC (PPE)…………………..
2006/42/EC……………………..
Annex IV………………………..
Notified Body:……………………….
Reg. No.:……………………………….
2004/108/EC…………………………
1907/2006/EC………………………………..
2009/142/EC……………………………
1935/2004/EC……………………………….
Harmonized standards used
EN 60745-1:2009+A11
EN 60745-2-15:2009+A1
EN 55014-1:2006+A1
EN 55014-2:1997+A1+A2
EN 61000-3-2:2006+A1+A2
EN 61000-3-3:2008
GüDE GmbH & Co. KG
birkichstrasse 6
74549 wolpertshausen
Deutschland
Tel.: +49-(0)7904/700-0
Fax.: +49-(0)7904/700-250
eMail: info@guede.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>