JBC HDE-9UD HDU Heavy Duty Control Unit Instruction Manual

JBC HDE-9UD HDU Heavy Duty Control Unit

Packing List

The following items are included:

• HDU Control Unit ……… 1 unit

• Power Cord ……………….. 1 uni t
  Ref. 0024077 (100V)
  0023717 (120V)
  0024080 (230V)

• Manual ………………………. 1 uni t
  Ref. 0028871

Features

Connections

Compatibility

Select the equipment that best suit your soldering or desoldering needs.

1. It works with two HDU Control Units in order to manage the cartridges individually
2. The MNE Nitrogen Flow Regulator is required.

Work Screen

The HDE offers an intuitive user interface which provides quick access to station parameters.
Default PIN: 0105

Troubleshooting

Station troubleshooting available on the product page at www.jbctools.com

Advanced Functionalities

• It provides detailed graphics of tip temperature and power delivery in real time during solder joint formation for analysis purposes. This helps you decide how to adjust your process or which tip to use to obtain the best quality soldering.
• Designed to avoid thermal shock when soldering Ceramic Chip components like MLCC, this new and unique feature allows controlling the heating ramp up rate of the tool to gradually increase the temperature of the component through all the phases of the soldering process. Up to 25 fully configurable soldering profiles can be stored.
• Get greater quality and control in your production. Manage your whole soldering process remotely in real time. For more information see www.jbctools.com/webmanager.html.
• Export graphics: Insert a USB flash drive into the USB-A connector to save your soldering process in csv format.
• Station update: Download the JBC Update File from www.jbctools.com/software.html
  Insert the USB flash drive with the file downloaded to the station.

System notifications

The following icons will be displayed on the screen’s status bar.

• USB flash drive is connected.
• Station is controlled by a PC.
• Station is controlled by a robot.
• Station software update. Press INFO to start the process.
• Warning.: Press INFO for failure description.
• Error. Press INFO for failure description, the type of error and how to proceed.

Soldering Net

Remotely manage and monitor as many stations as your Windows PC can handle.

1. Download the JBC Software Manager and the user manual from jbcnet.solutions
2. Connect the stations via USB-B connector and the PC will automatically detect them.
3. The notification will be displayed on the station.

Operation

The JBC Most Efficient Soldering System

Our revolutionary technology is able to recover tip temperature extremely quickly. It means the user can work at a lower temperature and improve the quality of soldering. The tip temperature is further reduced thanks to the Sleep and Hibernation modes which increase up to 5 times the life of the tip.

Work****

1. When the tool is lifted from the stand the tip will heat up to the selected temperature.
   Tool s Menu:

2. Set temperature limits

3. Select temperature levels

4. Sleep
   When the tool is in the stand, the temperature falls to the preset Sleep temperature. Tools Menu:

5. Set Sleep temperature

6. Set Sleep delay(from 0 to 9 min or no Sleep)

7. Hibernation
   After longer periods of inactivity, the power is cut off  and the tool cools down to room temperature. Tool s Menu :

8. Set Hibernation delay (from 0 to 60 min or no hibernation)

Maintenance

Before carrying out maintenance or storage, always allow the equipment to cool.

• Clean the station screen with a glass cleaner or a damp cloth.
• Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
• Periodically check that the metal parts of the tool and stand are clean so that the station can detect the tool status.
• Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
• Periodically check all cables and tubes.
• Replace a blown fuse as follows:

1. Pull off the fuse holder and remove the fuse. If necessary use a tool to lever it off.
2. Press the new fuse into the fuse holder and replace it in the station.

• Replace any defective or damaged pieces. Use original JBC spare parts only.
• Repairs should only be performed by a JBC authorized technical service.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

• Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

• The power cord must be plugged into approved bases. Be sure that it is properly grounded before
  use. When unplugging it, hold the plug, not the wire.

• Do not work on electrically live parts.

• The tool should be placed in the stand when not in use in order to activate the sleep mode. The
  soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station
  is turned off. Handle with care, including when adjusting the stand position.

• Do not leave the appliance unattended when it is on.

• Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

• Avoid flux coming into contact with skin or eyes to prevent irritation.

• Be careful with the fumes produced when soldering.

• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working
  to avoid personal harm.
  Utmost care must be taken with liquid tin waste which can cause burns.

• This appliance can be used by children over the age of eight and also persons with reduced physical,
  sensory or mental capabilities or lack of experience provided that they have been given adequate
  supervision or instruction concerning use of the appliance and understand the hazards involved.
  Children must not play with the appliance.

• Maintenance must not be carried out by children unless supervised.

Specifications

Warranty

JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement  of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

References

• JBC Soldering Stations, Irons and Rework equipment for electronics
• JBC Web Manager
• Warranty Extension

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>