HYPERX Charging Controller Grips for Mobile User Guide
- June 7, 2024
- HYPERX
Table of Contents
HyperX ChargePlay Clutch™ Quick Start Guide
Charging Controller Grips for Mobile
Overview
A Qi Wireless Transmitter F USB Type-A Port
B USB Type-C Port G Removable Battery Pack
C Qi Charging Status [LED] H Qi Wireless Receiver
D Power Button I Controller Grips
E Battery Status Indicators J Charging Cable
4402167 1
Charging
It is recommended to fully charge the battery before first use.
All four battery status indicators will illuminate solid when fully charged.
Wired Charging
Connect USB Type-C to 1 or 2 to charge battery pack.
Qi Wireless Charging
Place battery pack on a Qi wireless charging base.
Qi wireless charging base not included
2
Usage
1. 2.
3.
Power Button
Power on – Press to power on
Power off – Press and hold
Qi Charging Status LED
LED STATUS QI CHARGING STATUS
ON Charging
OFF Not Charging
Questions or Setup issues?
Contact the HyperX Support Team at: http://www.hyperxgaming.com/support
3
Battery Info
Battery Information
Capacity: 3000mAh/11.1Wh Li-ion Battery
Input: 5V 3A Max
Output: 5V 3A Max
Cannot be replaced by user
14
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
-
Reorient the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Canada Notices
This Class B digital apparatus complies with Canadian ICES-003. This device
complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Taiwan NCC Statement
NCC / DGT
Japan VCCI JRF Statement
CLass B ITE:
KCC Statement
B
Class B Equipment (For Home Use Broadcasting & Communication Equipment)
This equipment is home use (Class B) electromagnetic wave suitability
equipment and to be used mainly at home and it can be used in all areas.
HyperX is a division of Kingston.
THIS DOCUMENT SUBJECT TO CHANGE WITHOUT NOTICE
©2020 Kingston Technology Corporation, 17600 Newhope Street, Fountain Valley,
CA 92708 USA.
All rights reserved. All registered trademarks and trademarks are the property
of their respective owners.
15
Documents / Resources
|
HYPERX Charging Controller Grips for
Mobile
[pdf] User Guide
Charging Controller Grips for Mobile, 4402167
---|---