metabo SSE 18 LTX BL Cordless Sabre Saw Instructions
- June 5, 2024
- metabo
Table of Contents
SSE 18 LTX BL Cordless Sabre Saw
Instructions
| SSE 18 LTX BL
*1) Serial Number: 02267..
---|---
U| V| 18
n0| min-1 (spm)| 0-2700
s| mm (in)| 32 (1,26)
m| kg (Ibs)| 3,2 (7,05)
T1| mm (in)| 250 (10,2)
T2| mm (in)|
| 20 (0,8)
T2| mm (in)| | 140 (5,5)
LpA / KpA| dB (A)| 77 / 5
LWA/KWA| dB (A)| 88 / 5
ah,B/Kh,B| m/s2| 26,7 / 1,5
ah,WB/ Kh,WB| M/S2| 27,5 / 1,5
2) 2014/30/EU, 2006/42/EC, 2011/65/EU
3) EN 62841-1:2015, EN 62841-2-11:2016, EN 50581:2012
2019-08-19, Bernd Fleischmann
(Vice President Product Engineering & Quality)
*4) Metabowerke GmbH – Metabo-Allee 1 – 72622 Nuertingen, Germany
Conformity Declaration
We declare under our sole responsibility: These cordless saber saws, identified by type and serial number 1), comply with all relevant requirements of the directives 2) and standards 3). Technical file at 4) – see page 3.
Specified Use
The tool is suitable for sawing wood, metals, plastics, or similar materials
such as hard rubber, fiberglass, etc.
The user bears sole responsibility for any damage caused by unspecified use.
Generally accepted accident prevention regulations and the enclosed safety
information must be observed.
General Safety Instructions
For your own protection and for the protection of your electrical tool, pay
attention to all parts of the text that are marked with this symbol!
WARNING – Reading the operating instructions will reduce the risk of
injury.
WARNING – Read all safety warnings, instructions, illustrations, and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire, and/or serious
injury.
Save all warnings and instructions for future reference. Pass on your
electrical tool only together with these documents.
Special Safety Instructions
Hold the power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to
a stable platform. Holding the work by your hand or against the body leaves
it unstable and may lead to loss of control.
Remove the battery pack from the machine before any adjustment or
maintenance is carried out.
Before fitting the battery pack, make sure that the machine is switched off.
| CAUTION Do not stare at the operating lamp.
---|---
| Protect battery packs from water and moisture!
| Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs! Do not open battery packs! Do not
touch or short-circuit battery packs!
| Slightly acidic, flammable fluid may leak from defective Li-ion battery
packs!
| If battery fluid leaks out and comes into contact with your skin, rinse
immediately with plenty of water. If battery fluid leaks out and comes into
contact with your eyes, wash them with clean water and seek medical treatment
immediately.
If the machine is defective, remove the battery pack from the machine.
Always wear protective goggles, gloves, and sturdy shoes when working with
this tool.
Ensure that the spot where you wish to work is free of power cables, gas
lines, or water pipes (e.g. using a metal detector).
When sawing water pipes, ensure that they do not contain any water.
Wear ear protectors when working for long periods of time. High noise levels
over a prolonged period of time may affect your hearing.
Materials that generate dust or vapors that may be harmful to health (e.g.
asbestos) must not be processed.
Do not reach under the workpiece while the machine is in operation.
Do not try to see extremely small workpieces.
Clamp the workpiece firmly. Under no circumstances should you hold the
workpiece with your hand or foot.
Only use sharp, undamaged saw blades. Do not use saw blades that are cracked
or that have changed their shape.
For sawing, the guide must make secure contact with the workpiece.
Always hold the machine with both hands at the intended handles, take a secure
stance and concentrate on the work.
The danger of injury due to the sharp saw blade.
Do not touch the moving saw blade! Remove chips and similar material only with
the machine at standstill.
Remove the battery pack from the machine when not in use.
Reducing dust exposure:
WARNING – Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known to cause cancer,
birth defects, or other reproductive harm. Some examples of these chemicals
are:
- lead from lead-based paints,
- Crystalline silica from bricks and cement and other masonry products, and
- Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well-ventilated
area, and work with approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles.
This also applies to dust from other materials such as some timber types (like
oak or beech dust), metals, and asbestos. Other known diseases are e.g.
allergic reactions and respiratory diseases. Do not let dust enter the body.
Observe the relevant guidelines and national regulations for your material,
staff, application, and place of application (e.g. occupational health and
safety regulations, disposal). Collect the particles generated at the source,
and avoid deposits in the surrounding area.
Use suitable accessories for special work. In this way, fewer particles enter
the environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the exhaust air stream at yourself or nearby persons or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep clean using a vacuum cleaner. Sweeping or blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not blow, beat or brush.
Transport of li-ion battery packs:
The shipping of li-ion battery packs is subject to laws related to the
carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the
currently valid specifications when shipping li-ion battery packs. If
necessary, consult your freight forwarder. Certified packaging is available
from Metabo.
Only send the battery pack if the housing is intact and no fluid is leaking.
Remove the battery pack from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with adhesive tape).
Overview
See page 2.
1. Lever for setting the guide
2. Guide
3. Saw blade clamping fixture
4. LED working light
5. Lever of the saw blade clamping fixture
6. Front handle
7. Switch on the catch button| 8. Lock button (continuous operation)
9. Trigger
10. Rear handle
11. Battery pack release button
12. Battery pack
13. Capacity indicator button
14. Capacity and signal indicator
---|---
Assembly, Initial Operation, Setting
Remove the battery pack from the machine before any adjustment or maintenance
is carried out. Instructions on charging the battery pack can be found in the
operating instructions of the Metabo charger.
6.1 Battery pack
Charge the battery pack before use (12).
If performance diminishes, recharge the battery pack.
“Li-Power” li-ion battery packs have a capacity and signal indicator:
(14)
- Press the (13) button, the LEDs indicate the charge level.
- If one LED is flashing, the battery pack is almost flat and must be recharged.
Removal:
Press the battery pack release (11) button and pull the battery pack (12)
forwards.
Inserting:
Slide in the battery pack (12) until it engages.
6.2 Inserting, and removing saw blade
Do not touch the saw blade immediately following the operation of the tool, as
it can be extremely hot and can lead to skin burns.
- Pull up lever (5) of saw blade quick-clamping device upwards and hold in this position.
- Insert the saw blade as far as it will go or remove it.
- Release lever (5).
- Check that the saw blade is securely seated.
6.3 Setting the guide
The cutting depth can be limited by shifting the guide (2) (e.g. when sawing
in front of a wall).
Occasionally shift the guide (2) to achieve even wear of the saw blade.
- Swivel the lever (1) downwards and shift the guide (2) to the desired position. See image series B
- Swivel the lever (1) upwards and turn the guide (2), if needed, until the lever engages again.
Check guide (2) to ensure that it is securely fitted. It has to be engaged.
Use
7.1 Switching on and off, stroke rate, Switch-on lock (7):
Trigger (9) locked.
Trigger (9) unlocked.
Switching on, speed: press the trigger switch (9). The stroke rate can be
changed by pressing the trigger.
Switching off: Let go of the trigger switch (9). Continuous activation:
With the trigger (9) pressed, push in the locking button (8) and release the
trigger. Press and release the trigger (9) again to switch off.
In continuous operation, the machine continues running if it is forced out of
your hands. Therefore, always hold the machine with both hands using the
handles provided, stand securely and concentrate.
7.2 Stepless stroke rate-setting
The stroke rate can be changed steplessly by varying the pressure applied to
the trigger switch (9), thus adapting it to the material and working
conditions.
7.3 Working Directions Sawing:
Use a saw blade geared to the material to be sawn.
Press the machine with the guide (2) against the workpiece. Switch on the
machine, and only then guide the saw blade against the workpiece.
Do not make contact with any objects or with the ground with the moving saw
blade (danger of recoil and saw blade fracture!)
Adapt the stroke rate to the material to the sawn.
Avoid excessive pressure on the saw blade (particularly in the case of long
saw blades).
If the saw blade jams, turn the machine off immediately. Widen the sawn gap
slightly with a suitable tool and take out the machine.
After completing the sawing cut, switch off the machine and only take it out
of the sawn gap to place it down once the saw blade has come to a standstill
(danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials such as wood or plastic. Only
use short saw blades. Hold the machine with both hands at the intended
handles, take a secure stance and concentrate on the work.
See Fig. B, page 2: The machine is pressed with the edge of the guide (2)
against the workpiece. The saw blade does not make contact with the workpiece.
Switch on the machine. The corner of the guide serves as a pivot point around
which the machine is slowly aligned, whereby the saw blade cuts into the
workpiece.
Maintenance
On a regular basis, use compressed air to blow out the machine through the
rear ventilation slots.
Regularly clean the saw blade quick-clamping device (3) and blow out with
compressed air. Do not oil or grease.
Accessories
Use only original Metabo or CAS (Cordless Alliance System) battery packs and
accessories. See page 4.
Use only accessories which fulfill the requirements and specifications listed
in these operating instructions.
A. comprehensive range of saw blades for a wide variety of materials and use
cases
B. Battery charger: ASC 145 (6.27378), ASC 55 (6.27044)
C. Battery packs: 8,0 Ah (6.25369), 5,5 Ah (625368), 5,2 Ah (6.25592)
D. Lubricating stick for cooling the saw blades when sawing metal
For a complete range of accessories, see
www.metabo.com or the catalog.
Repairs
Repairs to electrical tools must be carried out by qualified electricians
ONLY!
If you have Metabo electrical tools that require repairs, please contact your
Metabo service center. For addresses see
www.metabo.com.
You can download spare parts lists from
www.metabo.com.
Environmental Protection
Observe national regulations on environmentally compatible disposal and on the
recycling of disused machines, packaging, and accessories.
Battery packs must not be disposed of with regular waste. Return faulty or
used battery packs to your Metabo dealer!
Do not allow battery packs to come into contact with water!
Only for EU countries: Never dispose of power tools in your household waste!
In accordance with European Guideline 2012/ 19/EU on used electronic and
electric equipment and its implementation in national legal systems, used
power tools must be collected separately and handed in for environmentally
compatible recycling. Before disposal, discharge the battery pack into the
power tool. Prevent the contacts from short-circuiting (e. g. by protecting
them with adhesive tape).
Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress are reserved.
U = Voltage of battery pack
n0 = Stroke rate at idle speed
s = Stroke length
T1 = max. cutting depth wood
T2 = max. cutting depth metal ( **= profiles, = tubes)
m = Weight (with smallest battery pack)
Measured values determined in conformity with EN 62841.
Permitted ambient temperature during operation: -20 °C (-4°F) to 50 °C (120°F)
(limited performance with temperatures below 0 °C (32°F)). Permitted ambient
temperature for storage: 0 °C (32°F) to 30 °C (86°F).
Direct current
The technical specifications quoted are subject to tolerances (in compliance
with the relevant valid standards).
Emission values
Using these values, you can estimate the emissions from this power tool and
compare these with the values emitted by other power tools. The actual values
may be higher or lower, depending on the particular application and the
condition of the tool or power tool. In estimating the values, you should also
include work breaks and periods of low use. Based on the estimated emission
values, specify protective measures for the user – for example, any
organizational steps that must be put in place.
Vibration total value (vector sum of three directions) determined in
accordance with EN 62841:
ah, B = vibration emission value (sawing of chipboards)
ah, WB = vibration emission value (sawing of wooden planks)
Kh,… = Uncertainty (vibration)
During operation, the noise level can exceed 80 dB(A).
Wear ear protectors!**
Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com
170 27 668 – 0820
Documents / Resources
|
metabo SSE 18 LTX BL Cordless Sabre
Saw
[pdf] Instructions
SSE 18 LTX BL, Cordless Sabre Saw, Sabre Saw, Cordless Sabre, SSE 18 LTX BL,
Saw
---|---
|
metabo SSE 18 LTX BL Cordless Sabre
Saw
[pdf] Instruction Manual
SSE 18 LTX BL, Cordless Sabre Saw, SSE 18 LTX BL Cordless Sabre Saw, Sabre Saw
|
metabo SSE 18 LTX BL Cordless Sabre
Saw
[pdf] Instruction Manual
SSE 18 LTX BL, SSE 18 LTX BL Cordless Sabre Saw, SSE 18 LTX BL Sabre Saw,
Cordless Sabre Saw, Sabre Saw, Cordless Saw, Saw
|
metabo SSE 18 LTX BL Cordless Sabre
Saw
[pdf] Instructions
602267850, SSE 18 LTX BL, SSE 18 LTX BL Cordless Sabre Saw, Cordless Sabre
Saw, Sabre Saw, Saw
|
metabo SSE 18 LTX BL Cordless Sabre
Saw
[pdf] Instruction Manual
SSE 18 LTX BL, Cordless Sabre Saw, SSE 18 LTX BL Cordless Sabre Saw
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>