Linkind LS56001182 Smart Pathway Lights User Manual
- September 20, 2024
- Linkind
Table of Contents
Linkind LS56001182 Smart Pathway Lights User Manual
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
-
This product is rated as IP66 Waterproof. It can be used outdoors but cannot be immersed in water.
-
The power adapter is rated as IP44 Waterproof. It can be used outdoors but cannot be rinsed or immersed in water.
-
Tighten up the waterproof cap before installing the pathway lights.
-
The internal light sources of the light bars and strip light cannot be replaced. If the light sources sustain damage, the product should be replaced.
-
Do not allow children to assemble and install this product without adult supervision.
-
Avoid installing this product near major heat sources.
External dimmers cannot be used with this product. -
Use this product with the provided power adapter only.
INTRODUCTION
Thank you for choosing Linkind Smart Pathway Lights.
This product has IP66 waterproof rating and supports three control methods:
button control, App control, and voice control. Color, brightness, etc. can be
adjusted through AiDot App.
| A | Switch colors |
|---|---|
| B | Switch scenes |
| Short press: On/Off Press and hold for more than 5s: Reset the device | |
| Indicator light | Flashing blue slowly: The device is in network configuration |
status. Steady blue: The device is online Off: The device is offline, or the device is not connected to power
Button A and Button B can configure more functions through the App. such as adjusting brightness, adjusting color temperature, random colors, countdown, etc.
SPECIFICATION
| Power input (adapter) | 120V AC 50/60Hz 0.8Amax |
|---|---|
| Power output (adapter) | DC24V 1.5A |
| Color | RGBWW |
| Color temperature | 2700K-6500K |
| Lumens | 200Im/per light |
| Number of lights | 4 |
| Length | 39.4ft (9.8ft between lights) |
| Wireless Protocol | 2.4GHz Wi-Fi& Bluetooth |
| Waterproof | Adapter (IP44) |
Control Box (IP65)
Pathway Lights (IP66)
Operating temperature| -20~45°C /-4~113°F
INSTALLING YOUR PATHWAY LIGHTS
-
Attach a ground stake to the stand of each LED Pathway Light.
-
Plug the power adapter into power.
Note: Avoid placing the control box directly on the ground, otherwise the Wi-Fi and Bluetooth connection may be intervened.
PAIRING YOUR DEVICE WITH THE AIDOT APP
What You Need:
- A Wi-Firouter supporting the 2.4GHz and 802.11 b/g/n bands (5GHz is not supported).
- A smartphone or tablet running i0S 12.0 (or above) or Android 6.0 (or above).
Pairing Instructions
Or search for” Ai Dot” in App Store or Google Play.
- Enable your smartphone’s Bluetooth.
- 0pen the App, tap the “+” icon in the top right corner and search for “Smart Pathway Lights”.
For more information, please visit www.linkind.com or contact our support team.
LIGHTS DETECTION
When connecting to the App for the first time or adding lights, you need to
click Lights Detection in the App
Note: Up to 6 lights can be connected
Troubleshooting
- Cannot connect to AiDot App.
- Make sure the device is powered on.
- Make sure your smartphone’s Bluetooth has been enabled.
- Make sure your smartphone is connected to a 2.4GHz Wi-Fi network.
- Position your smartphone close to the control box, then try connecting again.
- 0ne or more LED pathway lights fail to light up.
- Remove the light and then reattach it to the power cable. Also, unplug the power adapter and then plug backinto power.
- If the problem persists, please contact Linkind customer service.
- How many lights can be connected at most?
- Up to 6 lights can be connected
- Some lights cannot be controlled.
- Refresh the number of fixtures in the App.
- If the problem persists, please contact Linkind customer service.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
NEED HELP?
Our goal is to bring you the best shopping experience. If you have any
questions about our product, please feel free to contact us.
Our customer service team will be happy to provide assistance.
1877-770-5727 (Mon.-Fri. 9to 5 PST)
http://www linkind.com
Why not share your stories to help other buyers?
linking. lights
linkindofficial
linkindofficial Made in China
For FAQs and more information, please visit:
www.linkind.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>