ANKER A2038 Dual Port Charger User Manual

ANKER A2038 Dual Port Charger

Attention

• Read all the instructions before using the product.
• The product is designed for use with IT equipment only.
• Naked flame sources, such as candles, must not be placed on the product.
• The disconnection from line voltage is made by AC plug.
• In case of broken plugs, the product must be disposed of.
• If you want to clean the product, only use a dry cloth or brush.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• The power supply is not intended to be repaired by service personnel in case of failure or component defect (the product can be disposed of).

Using Your Product

For the fastest and safest charge, use an Anker® cable, your device’s original cable or another certified cable (such as MFi).

Specifications

PPS:3.3V -16V 2.5A (40W Max)

 | Use Two Ports :
 | Output: 20.0W + 20.0W (40.0W Max)
 | Total Output: 40.0W Max
Average active efficiency| 82.78%
Efficiency at low load (10%)| 69.36%
No-load power consumption| 0.14W
Operating Temperature| 0℃〜 25℃ /32 ℉ -77 ℉

Indoor use only

This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

For FAQs and more information, please visit: anker.com/support

Customer Service

• 18-month limited warranty
• Please note that your rights under applicable law governing the sale of consumer goods remain unaffected by the warranties given in this Limited Warranty.
• Lifetime technical support
  • support@anker.com
  • support.mea@anker.com (For Middle East and Africa Only)

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1 (800) 988 79733

This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

IC Statement
This digital apparatus complies with CAN ICES-003(B)/NMB-003(B).

Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2038 is in compliance with Directive 2014/35/EU & 2014/30/EU & 2011/65/EU & 2009/125/EC & 2019/1782/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com

Hereby, Anker Innovations Limited declares that the product type A2038 is in compliance with Electrical Equipment (Safety) Regulations 2016 & Electromagnetic Compatibility Regulations 2016 & The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 & The Ecodesign for Energy-Related Products Regulations 2010. The full text of the GB declaration of conformity is available at the following internet address: https://www.anker.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>