metabo BS 14.4 Quick Cordless Drill Screwdriver Instructions

BS 14.4 Quick Cordless Drill Screwdriver
Instruction Manual
Declaration of Conformity

We, being solely responsible: Hereby declare that these cordless drills/screwdrivers and impact drills, identified by type and serial number 1), meet all relevant requirements of directives 2) and standards 3). Technical documents for 4) – see page 3.For UK only:We as manufacturer and an authorized person to compile the technical file, see 4) on page 3, hereby declare under sole responsibility that these cordless drills/screwdrivers and impact drills, identified by type and serial number *1) on page 3, fulfill all relevant provisions of following UK Regulations S.I. 2016/1091, S.I. 2008/1597, S.I. 2012/3032 and Designated Standards EN 60745-1:2009+A11:2010, EN 60745-2-1:2010, EN 60745

Specified Use

The drills and impact drills are suitable for drilling in metal, wood, plastic and similar materials, and also for screw driving and thread tapping.The impact drills are also suited for drilling in masonry, brickwork and stone.The user bears sole responsibility for any damage caused by inappropriate use. Generally accepted accident prevention regulations and the enclosed safety information must be observed.

General Safety Instruction

For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol! Reading the operating instructions will reduce the risk of injury.

WARNING
Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury.Keep all safety instructions and information for future reference.Pass on your power tool only together with these documents.

Special Safety Instructions

Wear ear protectors with impact drills(machines with the designation SB). Exposure to noise can cause hearing loss.Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. A cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Ensure that the place where you wish to work is free of power cables, gas lines or water pipes (e.g. check using a metal detector). A slightly acidic, flammable fluid may leak from defective Li-ion battery packs! If battery fluid leaks out and comes into contact with your skin, rinse immediately with plenty of water. If battery fluid leaks out  and comes into contact with your eyes, wash them with clean water and seek medical attention immediately! Protect battery packs from water and moisture!Do not use faulty or deformed battery packs! Do not expose battery packs to fire! Do not open battery packs! Do not touch contacts or short-circuit battery packs! If the machine is defective, remove the battery pack from the machine.

Remove the battery pack from the machine before any adjustment or maintenance is carried out. Before fitting the battery pack, make sure that the machine is switched off. Keep hands away from the rotating tool! Remove chips and similar material only with the machine at a standstill. Secure the workpiece to prevent slipping or rotation (e.g. by securing with screw clamps). LED lights Do not observe the LED radiation directly with optical instruments.
Reducing dust exposure: Some of the particles generated using this power tool may contain substances known to cause cancer, allergic reactions, respiratory diseases, birth defects or other reproductive harm. Some examples of these substances are: lead (from lead-based paints), crystalline silica (from bricks cement, etc.), additives for wood treatment (chromate, wood preservative), some types of wood (like oak and beech dust), metals, asbestos. The risk from exposure to such substances will depend on how long the user or nearby persons are being exposed. Do not let particles enter the body. To reduce exposure to these substances: work in a well-ventilated area and wear protective equipment, such as dust masks that are specially designed to filter out microscopic particles. Observe the relevant guidelines for your material, staff, application and place of application (e.g. occupational health and safety regulations, disposal).

Collect the generated particles at the source, avoid deposits in the surrounding area. Use suitable accessories for special work. In this way, fewer particles enter the environment in an uncontrolled manner. Use a suitable extraction unit.Reduce dust exposure with the following measures:

• Do not direct the escaping particles and the exhaust air stream at yourself or nearby persons or on dust deposits.
•  Use an extraction unit and/or air purifiers.
•  Ensure good ventilation of the workplace and keep it clean using a vacuum cleaner. Sweeping or blowing stirs up dust.
• Vacuum or wash protective clothing. Do not blow, beat or brush.

Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws related to the carriage of hazardous goods (UN 3480 and UN 3481). Inform yourself of the currently valid specifications when shipping li-ion battery packs. If necessary, consult your freight forwarder. Certified packaging is available from Metabo. Only send the battery pack if the housing is intact and no fluid is leaking. Remove the battery pack from the machine for sending. Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Overview

1.  Drill chuck/drill chuck sleeve*
2. Adjusting sleeve (torque control, maximum torque) *
3. Adjusting sleeve (screw driving, drilling, impact drilling) *
4. Adjusting sleeve (torque limitation) *
5.  Slide-switch (1st/2nd gear)
6. Belt hook
7.  Rotation selector switch (direction of rotation setting, transporting safety device)
8. Trigger switch
9. Handle
10.  LED lights
11.  Battery pack release button
12.  Battery pack *
13. Capacity and signal indicator
14. Capacity indicator button

Use

1. The battery pack is almost flat (the electronics prevent the battery pack from discharging totally and avoid irreparable damage).
2. If one LED\ is flashing, the battery pack is almost flat. If necessary, press the button (14) and check the LEDs (13) to see the charge level. If the battery pack is almost flat, it must be recharged!
3. Long continuous overloading of the machine will activate the temperature cut-out.
4. Leave the machine or battery pack to cool. Note: The machine will cool more quickly if you operate it at idling speed. machine seizes continuously for long periods), the machine switches off. Switch off the machine at the trigger switch\ Then continue working as normal. Try to prevent the machine from seizing.

Battery pack
Charge the battery pack before use.If performance diminishes, recharge the battery pack.The ideal storage temperature is between 10°C and 30°C.In case of Li-Ion battery packs with capacity and signal display (13) (equipment- specific):- Press the button (14), the LEDs indicate the charge level.If one LED is flashing, the battery pack is almost flat and must be recharged.

Removing and inserting the battery pack
Removal: Press the battery pack release button (11) and pull the battery pack (12) forwards.Insertion: Slide the battery pack (12) in until it engages.

Setting the direction of rotation

Actuate the rotary selector switch (direction of rotation set, transporting safety device) (7).
See page 2:
R = Clockwise setting
L = Counter-clockwise setting
0 = middle position: transportation safety device
(Switch-on lock) set

Selecting gear stage
particularly high torque, preferable for screwing) gear (high speed, preferable for drilling) Set torque limitation, screw driving, drilling, impact drill Machines with the designation BS…

1. 20 = Set torque (with torque limitation) by turning the sleeve
2. intermediate settings are also possible.
3. = Set drilling by turning the sleeve  (max. torque, without torque limitation) To avoid overloading the motor, do not jam the spindle. Machines with the designation SB…:
4. = Set screw driving by turning the sleeve AND set the torque (with torque limitation) by turning the sleeve (4) – intermediate settings are also possible.
5. = Set drilling by turning the sleeve (3) (max. torque, without torque limitation) To avoid overloading the motor, do not jam the spindle.
6. Set impact drilling by turning the sleeve (3) (max. torque, without torque limitation) To avoid overloading the motor, do not jam the spindle.

Change accessory
Opening the drill chuck: Turn the drill chuck sleeve  clockwise. Clamping the tool: Open the drill chuck and insert the tool as far as possible. Turn the drill chuck sleeve (1) in a clockwise direction until the tool is clamped securely. With a soft tool shank, retightening may be required after a short drilling period.

Switching power tool on/off, setting
speed press the trigger switch (8) to switch on the machine. Press in the trigger to increase the rotational speed.

Drill chuck with “Quick” change system
(for BS 18 Quick, BS 14.4 Quick) Removal: See page 2, fig. A. Push the interlocking ring forward (a) and pull off the drill chuck (b). Mounting: Push the interlock ring forward and move the chuck as far as the limit stop on the drill
spindle.
Drill chuck (for BS 14.4, BS 18, SB 18)
See page 2, fig. B. Undo the locking screw. Caution left-handed thread! Clamp an Allen key in the chuck and strike lightly with a rubber hammer to loosen, then unscrew. Employ the same procedure when attaching the chuck, except in reverse order

 Accessories

Use only original Metabo or CAS (Cordless Alliance System) battery packs and accessories. See page 4. Only use accessories that fulfill the requirements and specifications listed in these operating instructions.

•  Quick clamping chuck.
• Battery packs with different capacities. Only use battery packs with a voltage suitable for your power tool.
•  Angle screwdriver attachment.
• Battery charger
•  Bit holder with Quick replacement system
• Bit box

Repairs

Repairs to electrical tools must ONLY be carried out by qualified electricians! Contact your local Metabo representative if you have Metabo power tools requiring repairs. See www.metabo.com for addresses. You can download a list of spare parts from www.metabo.com.

Environmental Protection

Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories. Battery packs may not be disposed of with regular waste. Return faulty or used battery packs to your Metabo dealer!Do not allow battery packs to come into contact with water! Protect the environment, and do not dispose of power tools and battery packs with household waste. Observe national regulations on separated collection and recycling of disused machines, packaging and accessories. Before disposal, discharge the battery pack in the power tool. Prevent the contacts from short- circuiting (e. g. by protecting them with adhesive tape).

Technical Specifications

Explanatory notes on the specifications on page 3. Changes due to technological progress are reserved.

Emission values

Using these values, you can estimate the emissions from this power tool and compare these with the values emitted by other power tools. The actual values may be higher or lower, depending on the particular application and the condition of the tool or power tool. In estimating the values, you should also include work breaks and periods of low use. Based on the estimated emission values, specify protective measures for the user – for example, any organizational steps that must be put in place. Vibration total value (vector sum of three directions)

References

• Сайт в разработке
• Metabo - Power Tools for professional users
• Metabo - Elektrické nářadí pro profesionální uživatele

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>