EPROPULSION Evo Control and Evo Tiller System Installation Guide
- June 5, 2024
- EPROPULSION
Table of Contents
Evo Control System
Installation Guide
2020.12 Version 1.0
Copyright © 2020 ePropulsion All Rights Reserved
Acknowledgement
Thanks for choosing propulsion products, your trust, and support in our
company are sincerely appreciated. We are dedicated to providing high-
performance products and accessories. Welcome to visit
www.epropulsion.com and contact us if you have
any concerns.
Using This Manual
Before use of the product, please read this user manual thoroughly to
understand the correct and safe operations. By using this product, you hereby
agree that you have fully read and understood all contents of this manual.
propulsion accepts no liability for any damage or injury caused by operations
that contradict this manual. Due to the ongoing optimization of our products,
propulsion reserves the right to constantly adjust the contents described in
the manual. propulsion also reserves intellectual property rights and
industrial property rights including copyrights, patents, logos, designs, etc.
This manual is subject to update without prior notice, please visit our
website
www.epropulsion.com for the latest version. If
you find any discrepancy between your products and this manual, or should you
have any doubts concerning the product or
the manual, please visit www.epropulsion.com.
propulsion reserves the right of final interpretation of this manual. This
manual is multilingual, in case of any discrepancy in the interpretation of
different language versions, the English version shall prevail.
Symbols
The following symbols will help to acquire some key information.
Important instructions or warnings
Useful information or tips
Product Identification
The below picture indicates the serial numbers of Evo Remote Control and Evo
Tiller. Please note the position of the serial numbers and record them for
access to warranty service and other after-sale services.
Product Overview
The Evo Remote Control and Evo Tiller are used for starting and stopping the outboard motor, adjusting the speed of the motor, configuring the battery parameters, displaying the system information and messages, etc. The Evo Remote Control is powered by either solar power or the built-in lithium battery, but the Evo Tiller is powered by connecting to the outboard with a communication cable. Evo Remote Control wirelessly or wired communicates with the outboard control system built in the main outboard motor, and Evo Tiller can only wire communication with the outboard. The Evo Tiller itself owns the steering capability, while using the Evo Remote Control, it requires an additional steering wheel to help steer.
1.1 In the Package
When you receive a set of Evo Remote Control or Evo Tiller, unpack its package
and check if all the items below are included in the package. If there is any
loss or transport damage, please contact your dealer immediately.
| Items | Qty./Unit | Figure |
|---|---|---|
| Evo Remote Control / Evo Tiller | 1 set | 
Fixing Guide (Only provided with Remote Control)| 1 piece|
User Manual, Warranty Card & Invitation Card| 1 set|
Kill Switch| 2 pieces|
1.2 Parts and Diagrams
Specification
Evo Remote Control
| Communication | Wireless / Wired |
|---|---|
| Communication Distance | ≤10 m |
| Weight | 0.65 kg / 1.43 lbs. |
| Dimension (L x W x H) | 193 mm x 130 mm x 112 mm /7.6” x 5.1” x 4.4” |
Evo Tiller
| Communication | Wired |
|---|---|
| Weight | 1.1 kg / 2.43 lbs. |
| Dimension (L x W x H) | 513 mm x 90 mm x 114 mm / 20.2” x 3.5” x 4.5” |
Installation
2.1 Mounting the Evo Remote Control
Refer to the remote control fixing guide to punch holes on the shipboard, and
use the screws to lock the remote control box as shown in Figure 2-1.
2.2 Mounting the Evo Tiller
2.2.1 Mounting on the SPIRIT 1.0 Evo
- Install the tiller to the machine (Figure 2-2).
- Insert the handle shaft into the hole to the end and lock it counterclockwise (Figure 2-3).
2.2.1 Mounting on the NAVY 3.0 Evo/NAVY 6.0 Evo
- Install the tiller to the machine (Figure 2-4).
- Insert the handle shaft into the hole to the end and lock it clockwise (Figure 2-5).
Wiring
3.1 Connecting the remote control and the outboard
If the remote control needs to be connected to the machine by wire, a
communication cable is needed to connect the machine and the remote control
Communication port (Figure 3-1).
3.2 Connecting the tiller and the outboard
After mounting the tiller, you need to connect the communication port of the
tiller to the communication port of the machine (Figure 3-2).
Charging
The Evo Remote Control has a built-in lithium battery for power supply. The
battery will be charged automatically under normal use: get charged by solar
power or a wired connection. The Evo Tiller does not have a built-in battery
and needs to be connected to the machine.
4.1 Charging by solar power
When the solar panel receives enough sunshine, it will generate electricity to
charge the built-in lithium battery. While charging the battery by solar
power, it’s suggested to face the solar panel of the Remote Control toward
sunlight to get a better-charging effect.
It’s recommended to charge the Remote Control by solar power.
4.2 Charging by wired connection
If the Evo Remote Control can’t get enough solar power for a long time, the
battery level will run out. In this case, a warning message with an error code
E60 (Figure 4-2) will display on the LCD panel to remind you to charge the
Remote Control.
Please follow the below steps to charge the Remote Control by a wired
connection.
First, connect the Remote Control to the outboard motor by a communication
cable first (Figure 4-3); Then, connect the outboard motor to the battery.
During long-term storage, ensure to charge the Remote Control battery every 6
months to avoid over-discharge.
After long-term storage, charge the Remote Control before use.
The communication cable is not included in this package. Please purchase one
from your dealer if you choose this charging method.
It’s recommended to switch off the Remote Control while connecting the
communication cable. When the Remote Control is switched on while charging, as
the outboard main part and Remote Control are in communication, the working
outboard motor will stop once the communication cable disconnects.
Use of Kill Switch
- Locate the kill switch to the right place on the Evo Remote Control / Evo Tiller and tie its lanyard to your wrist or life jacket.
- Stop the outboard in an emergency by detaching the kill switch.
- To run the motor again, first, attach the kill switch then start the motor.
The kill switch generates a magnetic field. Keep it 50cm / 20inches away from
medical implants like pacemakers and magnetic cards (e.g. credit cards) as
well as other magnetic media.
The magnetic field of the kill switch may interfere with some electronic
instruments. Keep it away from these electronic instruments.
Warranty
The propulsion limited warranty is provided for the first-end purchaser of a propulsion product. Consumers are entitled to a free repair or replacement of defective parts or parts which do not conform with the sales contract. This warranty operates in addition to your statutory rights under your local consumer law.
6.1 Warranty Policies
propulsion warrants its products to be free of defects in material and
workmanship for a limited period from the date of purchase. Once a fault is
discovered, the user has the right to make a warranty claim under the
propulsion warranty policies.
| Product | Warranty Expiry Date |
|---|---|
| Evo Remote Control /Evo Tiller | Two years after the date of purchase. |
| Components have been repaired or replaced | Three months since the date of |
maintenance.
Note:
1. If the three-month period overlaps with the original warranty period, the
warranty against these replaced or repaired parts still expires two years
after the date of purchase.
2. If the three-month period exceeds the original warranty period, the
repaired or replaced parts continue applying to the warranty during the
extended period.
In order to validate the warranty, users are required to fill in the Warranty
Card in the package in advance.
Keep the product label in an intact state and record the serial number on the
label. Never tear the label of the product. A propulsion product without the
original product label will not be applicable to warranty services provided by
propulsion.
The warranty is valid only when the information is correct and complete.
The free warranty is only validated upon the presentation of the legal serial
number, Warranty Card, and evidence of purchase from an authorized propulsion
dealer.
The valid date of purchase should be established by the first-hand purchaser
with the original sales slip.
Free warranty is not transferable and will not be reissued.
Within the limits of the applicable laws, the warranty policies of propulsion
may update without prior notice. The latest version is available at our
website www.epropulsion.com.
6.2 Out of Warranty
Make sure the product is properly packed during delivery, the original
propulsion package is recommended. If the product got further damaged due to
improper packing during delivery, the furtherly damaged part will be deemed as
out of warranty coverage.
In addition, faults or damages caused by the following reasons are also excluded from the warranty scope within the covered period:
- Any improper operation contradicts the user manual.
- Accident, misuse, wishful abuse, physical damage overcharging, liquid damage, or unauthorized repair.
- Dropping, improper care, or storage.
You should be noted that minor faults like normal wear and tear that pose no
influence on the intended function of the product are also not covered by the
warranty.
Consumables are out of warranty scope.
6.3 Warranty Claim Procedures
If you find your product defective, you can make a claim to your dealer
following the below procedures:
-
Fill in the Warranty Card correctly and completely in advance. Then make your warranty claim by sending it to your authorized propulsion service partner together with valid proof of purchase. Usually, these documents are required when making a warranty claim: the Warranty Card, ex-factory serial number, and evidence of purchase.
-
Send the defective product to your authorized propulsion service point after getting the confirmation. Note that the label should be kept intact. You can also deliver the product to your authorized propulsion dealer after getting confirmation.
-
The defective components or parts will be either repaired or replaced according to the diagnosis made by the propulsion authorized service partner.
-
If your warranty claim is accepted, the equipment will be repaired or replaced free of cost. Note that any delivery cost incurred in the process is at your charge.
-
After careful examination and confirmation by the propulsion authorized dealer, the defective or faulty components will be repaired or replaced with brand new ones against the actual condition.
-
In case your warranty claim is rejected, an estimated repair charge with the round trip delivery cost will be sent for confirmation. propulsion authorized service point will conduct maintenance accordingly only after your confirmation.
If the warranty expires, you can still enjoy maintenance services from authorized propulsion service partners with a minimum maintenance charge.
Thanks for reading this user manual.
If you have any concerns or find any problems while reading, please don’t
hesitate to contact us. We are delighted to offer our service to you.
Guangdong propulsion Technology Limited
Website: www.epropulsion.com
Email: service@epropulsion.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>