dji CP.OS.00000123.01 Wireless Microphone Transmitter User Guide

DJI
Wireless Microphone Transmitter
User Guide v1.0 2020.08

In The Box

Disclaimer and Warning

Congratulations on purchasing your new DJI OSMOTm product. Please read this entire document and all safe and lawful practices DJI OSMO provided carefully before use. Failure to read and follow instructions and warnings may result in serious injury to yourself or others, damage to your DJI OSMO product, or damage to other objects in the vicinity. By using this product, you hereby signify that you have read this document carefully and that you understand and agree to abide by all terms and conditions of this document and all relevant documents of this product. You agree to use this product only for purposes that are proper. You agree that you are solely responsible for your own conduct while using this product, and for any consequences thereof. DJI OSMO accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product.
OSMO is a trademark of SZ OSMO TECHNOLOGY CO., LTD. (abbreviated as “DJI OSMO”) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies. This product and document are copyrighted by DJI OSMO with all rights reserved. No part of this product or document shall be reproduced in any form without the prior written consent or authorization of DJI OSMO.
This document and al I other collateral documents are subject to change at the sole discretion of DJI OSMO. For up-to-date product information, visit http://www.dji.com and click on the product page for this product. This document is available in various languages. In the event of divergence among different versions, the English version shall prevail.

Warnings

1. The product should be used in temperatures from 0°C to 40°C. The use of the product in environments above 40°C can lead to a fire or explosion.
   The use of products below 0°C can lead to permanent damage.

2. Discharge the battery to 40%-65% if it will NOT be used for 10 days or more. This can greatly extend the battery life.

3. Discharge and charge the battery completely once every three months to keep it in good condition.

4. The microphone windscreen shall be properly kept to prevent loss.

Introduction

The DJI Wireless Microphone Transmitter (hereinafter referred to as ‘Wireless Mic”) is a compact and portable device with an internal microphone. It can be clipped to clothing or any place close to a sound source. Used with DJI Pocket 2 Do-It-All Handle, the Wireless Mic operates on the 2.4 GHz band and transmits clear and high-quality voice wirelessly to DJI Pocket 2. It can also transmit voice to DJI Wireless Microphone Receiver.

1. Internal Microphone

2. Microphone Windscreen Port Used to secure the microphone windscreen.

3. 3.5mm Port Used to connect with an external microphone.

4. Connection Status LED Used to indicate the connection status of the Wireless Mic. Refer to the Status LED Descriptions for more information.

5. Linking Button Used to connect with DJI Pocket 2 for shooting or recording or to link with the Do-It-All Handle or Wireless Microphone Receiver.

6. Power Button Toggle up or down to power on or off.

7. Charging Status LED Used to indicate the battery level or system status. Refer to the Status LED Descriptions for more information.

8. Charging Port
   Used to charge the Wireless Mic.

9. Clamp
   Used to attach to clothing or the cold shoe of a camera.

Usage

Powering on
Toggle the power button up to power on.

Connecting the Wireless Mic
After connecting the DJI Pocket 2 with the Do-It-All Handle, swipe down on the touchscreen of DilPocket2.Swipelefttofindthe Wireless Mic icon and tap to enable linking with the Do-lt-All Handle. Power on the Wireless Mic and press the linking button.

If linking is successful, the Wireless Mic icon will turn to .
The next time the Wireless Mic is powered on, it will automatically link with the device it was last connected to.
If users wish to switch to another wireless mic when there is already a wireless mic connected, they can choose any of the following methods:

1. Power off the connected mic and refer to the Connection section to link and connect to other mics.
2. Tap the Wireless Mic icon on the touchscreen of DJI Pocket 2. Tap Disconnect on the prompt to disconnect the mic from DJI Pocket 2. Refer to the Connection section to link and connect to other mics.

Charging the Wireless
Mic To charge the Wireless Mic, connect a USB adapter (not included) to the charging port using the provided charging cable.
Charging time: approx. 60 minutes*(when using a USB adapter of 5V/0.4A).

• Charging time was tested in a lab environment at room temperaturesof77°F(25°C) and should be used for reference only.
  Using the Wireless Mic
  When the Wireless Mic connects with DJI Pocket 2 via the Do-It-All Handle, it transmits audio signals to DJI Pocket 2 immediately. When using the Wireless Mic, the icon will dynamically display the volume bar Press the linking button to shoot or record.
  The clamp of the Wireless Mic can be attached to clothing or the cold shoe of a camera.
  The 3.5mm port can also be used to connect with a TRS or TRRS wired microphone.
  The microphone windscreen can reduce wind noise effectively.
  It can connect to an external power source for charging via the USB-C port.

Status LED Descriptions

Refer to the table below for more information.
Connection Status LED Descriptions (Located on Top)

Connected with External Microphone| Blinking Pattern| Description
---|---|---
No| Blinks green rapidly| Linking with a device
Solid green| Connected to the Do-It­All Handle or Wireless Microphone Receiver
Blinks green slowly| Failed to connect with the Do-It-All Handle or Wireless Microphone Receiver, or exceeded the transmission distance
Yes| Blinks yellow rapidly| Linking with a device
Solid yellow| Connected with the Do­lt-All Handle or Wireless Microphone Receiver
Blinks yellow slowly| Failed to connect with the Do-It-All Handle or Wireless Microphone Receiver, or exceeded the transmission distance

Charging Status LED Descriptions ( Located on Bottom)

Status

| Blinking Pattern|

Descriptions

---|---|---
Battery Level Display| Solid green| 15-100%
Solid red| 5-15%
Blinks red slowly| 0-5%
Charging the Wireless Mic| Blinks green| 0-25%
Blinks green twice| 25-50%
Blinks green three times| 50-75%
Blinks green four times| 75-100%
Solid green for 6 seconds and turns off| Fully charged

Descriptions of Other Blinking Patterns

level is low and the device is about to power off
Blinks red and green alternatively| Blinks red and green alternatively| Updating Firmware
Solid red| Solid yellow| There is an error and the Wireless Mic must be powered on. Contact DJI Support if the issue persists.

Updating Firmware

The Do-It-All Handle must be attached to DJI Pocket 2 in order for the Wireless Micro con to connect to Di I Pocket 2 to update its firmware. If an update is available, the firmware of the Do-It-All Handle will be updated first. Afterward, the Wireless Mic links and connects with the Do-It-Handle. A prompt will appear onscreen with instructions on how to update the firmware of the Wireless Mic.

• Refer to the OP Pocket 2 Do-It-All Handle User Guide for more information on how to update the firmware.
  DO NOT operate the DJI Pocket 2, Do-It-All Handle, or Wireless Mic while updating firmware. Otherwise, the update may fail.

Specifications

Latency

SZ DJI Osmo Technology Co., Ltd.
2F, Building 3, Binhai Mingzhu
Industrial Park No.291 Looming Road,
Xinhua Street Guangming District,
Shenzhen, China

Compliance Information

FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
SAR tests are conducted using standard operating positions accepted by the FCC/ ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output.
Before a new model device is available for sale to the public, it must be tested and certified to the FCC/ ISEDC that it does not exceed the exposure limit established by the FCC/ ISEDC, Tests for each device are performed in positions and locations as required by the FCC/ ISEDC. For face-up, Omm was used for the test, this equipment should be installed and operated with a minimum distance of 0 mm
For body-worn operation, this model device has been tested and meets the FCC / ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 0mm from the body.
Non-compliance with the above restrictions may result in a violation of RF exposure guidelines.

ISED Compliance Notice

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

EU Compliance Statement:
SZ DJI Osmo Technology Co., Ltd. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online atwww.dji.com/euro-compliance
EU contact address: MI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
Environmentally-friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycling valuable raw materials and the treatment of toxic substances.

DJI Support
http://www.cfp.comfsupport
OSMO POCKET is a trademark of DJI OSMO.
Copyright 0 2020 DJI OSMO All Rights Reserved.
Printed in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>