MONSTER MH21903 Clarity 6.0 ANC Wireless Earphones User Guide
- June 5, 2024
- Monster
Table of Contents
MONSTER MH21903 Clarity 6.0 ANC Wireless Earphones
Product Overview
In‐ear Earphones (left & right) Charging Case
USB‐C Charging Cable
Ear Tips × 3 pairs (M size installed) Quick Start Guide and Warranty Letter
- Multi Function Button（MFB）
- Indicator Light (White)
- Microphones
- Ear Tip
- USB‐C Charging Port
- Pair/ Reset to Factory Settings Button
- Charging Case
- Charging Case Indicator Light
Power On/Off
The earphones will be turned on when opening the charging case. To turn off
the earphones, put back to the charging case and close. Earphones will be
turned off and start charging.
Noise Cancellation On/Off
Press and hold the MFB for about 2 seconds to switch different mode.
[Noise Cancellation On] – [Transparency Mode] – [Noise Cancellation Off]
Transparency Mode
Charging case
Connect the included USB‐C cable to charge the charging case. During the
charging process, the charging case light indicator will show the current
charge status. When the charging case is fully charged, the light will turn
off.
Pairing
Open the charging case, the earphones will be turned on automatically. Left
and right earphones will be connected automatically within few seconds. Then
“pairing” voice prompt will be heard. For new device connection, go to the
Bluetooth settings on your device and set it to search for new devices (new
Monster device). Once the earphones are paired to the designated device, you
will hear “connected”.
Connect other devices
Keep the earphones in the charging case and leave the cover open. Press and
hold the pair button which is located on the bottom of the charging case for
about 2 seconds until the light indicator start to flash. It is now in pairing
mode. Activate the Bluetooth on your device and set it to search for new
devices.
Volume Control
The earphones do not have a volume control function. After Bluetooth
connection, volume level can be controlled on the connected device.
Calling
Answer/End call: Click the MFB.
Reject a call: Double‐click the MFB.
Music
Play/Pause music: Short press the MFB.
Previous song: Double‐click the MFB on the left earphone.
Next song: Double‐click the MFB on the right earphone.
Voice Control
After connecting to the phone, triple‐click the MFB quickly to activate the
voice assistant.
LED Indicator Guide
Mode
| ****
Description
| ****
Voice prompts
---|---|---
Power On
| Indicator light stays on about 1 second.| ****
“Power On”
Power Off
| Indicator light stays on about 1 second.| ****
“Power Off ”
Pairing
| Indicator light flashes quickly.| ****
“Pairing”
Connected
| ****
After connected, Indicator light goes off.
| ****
“Connected”
Earphones charging
| When left earphones is charging, the left indicator light is on.
| ****
When right earphones is charging, the right indicator light is on.
When both earphones are charging, the left and right indicator lights are on respectively.
Charging case
| Charging case indicator light flashes while charging. When charging case indicator light is
off, it is fully charged.
| ****
‐
Note:
- After removing the earpieces from the charging case, without pressing any buttons, the left and right earpieces will connect automatically. If there is no connection found, it enters to pairing mode automatically.
- Please put the earphones in the correct position to charge.
- It is not recommended to replace the battery privately.
- The battery (battery pack or combination battery) must not be exposed to excessive heat such as sunlight or fire.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>