Nedis WIFILS51CRGB Smart Wi-Fi LED Strip User Manual

: June 5, 2024
: nedis

WIFILS51CRGB Smart Wi-Fi LED Strip

Nedis WIFILS51CRGB Smart Wi-Fi LED Strip

User Manual

Preface

Thank you for purchasing the Nedis WIFILS51CRGB.

This document is the user manual and contains all the information for correct, efficient and safe use of the product.

This user manual is addressed to the end user. Read this information carefully before installing or using the product.

Always store this information with the product for use in the future.

Product description

Intended use

This product is a Smart Wi-Fi LED strip with a wireless remote control.

The product is not intended for professional use.

This product is intended for indoor and outdoor use.

Any modification of the product may have consequences for safety, warranty and proper functioning.

Specifications

Product

|

Smart Wi-Fi LED Strip

---|---

Article number

|

WIFILS51CRGB

LED strip

LED strip length

|

5 m

LED strip width

|

10 mm

Brightness

|

900 lm

Light colour

|

RGB

LED type

|

5050

LED quantity

|

30 per meter

Connection

|

3 pins at 2.5 mm each

Power

|

24 W

Waterproof

|

IP65

Controller

Dimensions

|

70 x 30 x 15 mm

Input voltage

|

12 V

Max. current

|

2.0 A

Rated power

|

24 W

Frequency range

|

2412 – 2484 MHz

Max. transmit power

|

16 dBm

Waterproof

|

IP20

Main parts (image A)

A

1. Power cable

2. Controller

3. Brightness buttons

4. Power button

5. Mode button

6. Controller plug

7. IR receiver

8. LED strip

9. IR remote

10. Music mode

11. Speed buttons

12. Colour buttons

13. Start/stop moving pattern

Safety instructions

WARNING

Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep the packaging and this document for future reference.
Only use the product as described in this document.
Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
Do not drop the product and avoid bumping.
Do not expose the product to water or moisture.
This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
Do not unplug the product by pulling on the cable. Always grasp the plug and pull.
Only power the product with the voltage corresponding to the markings on the product.
Wipe the battery terminals with a clean dry cloth if they are dirty.
Non-rechargeable batteries are not to be recharged.
Do not short-circuit a battery.
Children of less than 8 years should be kept away.
Cleaning and user maintenance shall not be done by children without supervision.
Make sure to match the charger voltage to the voltage on the battery markings. Wrong voltage can destroy the charger and/or battery.
The security circuit ensures that there is no voltage at the battery clamps when there is no battery connected.
Make sure to match the (+) and (-) polarity markings.
Do not clean the inside of the product.

Explanation of the symbols on the product or packaging

Icon

|

Description

---|---

|

Product in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions such as double insulation or reinforced insulation are provided, there being no provision for protective earthing or reliance upon installation conditions. NOTE A Class II products may be provided with means for maintaining the continuity of protective circuits, provided that such means are within the product and are insulated from accessible surfaces according to the requirements of Class II.

|

Indication to explain the product is suitable for indoor use only.

|

Electronic equipment needs to bear the CE mark in order to be marketed in the EU. CE marking shows that a product is assessed before being placed on the market and that it meets EU safety, health and environmental protection requirements. CE marking is also sometimes accepted as a means of compliance with type-approval requirements; for example, electronic components that require type-approval and also CE marking for electromagnetic compatibility (EMC) or low-voltage equipment.

|

Indication to explain that the product needs to be collected separately when disposed. Do not throw in the trash bin.

Installation

Check the contents of the package

Check that all parts are present and that no damage is visible on the parts. If parts are missing or damaged, contact the Nedis B.V. service desk via the website: www.nedis.com.

Installing the app

Download the Nedis Smartlife app for Android or iOS on your phone via Google Play or the Apple App Store.
Open the Nedis Smartlife app on your phone.
Create an account with your mobile phone number or your e-mail address and tap Continue.
Enter the received verification code.
Create a password and tap Done.
Tap Add Home to create a SmartLife Home.
Set your location, choose the rooms you want to connect with and tap Done.

Connecting the product

1. Plug the power cable A1 into the controller A2.

2. Plug the controller plug A6 into the LED strip A8.

3. Plug A1 into a power outlet.

4. Check if A8 is blinking. If so, confirm in the app.

If A8 does not blink, press and hold the power button A4 on A2 for 5 seconds.

5. Tap + in the top right corner.

6. Under _ Search Device, _select the product from the list of available devices.

7. Check if A8 is blinking. If so, confirm in the app.

8. Enter the password of the Wi-Fi network to which your phone is connected and tap Confirm.

9. Rename the product after it has been found and added.

Setting up the product

1. Unplug A1 from the power outlet.

2. Clean the surface from dust and grease.

The surface must be smooth. Do not place the product on knitted/wool fabrics, dust wall, rough plastic surface or frosted glass.

3. Remove part of the 3M tape from the back of A8.

4. Place the start of A8 in the desired position.

5. Make sure the power outlet is within reach.

6. Unroll A8.

7. Remove the 3M tape and press A8 into the desired position.

8. Firmly press A8 down with your hand.

Do not use hard objects to press A8 down to prevent damage.
Do not bend A8 at sharp angles to prevent damage.
If desired, cut A8 to size on the indicated cut lines.
Cutting A8 removes the waterproof qualities of the product.

9. Plug A1 into a power outlet.

Use

Controlling the product

1. Press A4 to switch the product on or off.

2. Press and hold A4 on A2 for 5 seconds to factory reset the product.

3. Press the mode button A5 to change modes.

4. Press the brightness buttons A3 to adjust the brightness.

5. Press the colour buttons A12 to adjust the colour.

6. Press the speed buttons A11 to adjust the speed.

The product can be connected to Google Home or Amazon Alexa to enable speech control.

Maintenance

Before cleaning and maintenance, switch off the product and disconnect the power. Let the product cool down.

Clean the product regularly with a soft, clean, dry cloth. Avoid abrasives that can damage the surface.

Do not use aggressive chemical cleaning agents such as ammonia, acid or acetone when cleaning the product.

Warranty

Any changes and/or modifications to the product will void the warranty. We accept no liability for damage caused by improper use of the product.

This product is designed for private use (normal domestic use) only. Nedis is not responsible for wear, defect and/or damages caused by commercial use of the product.

Disclaimer

Designs and specifications are subject to change without notice. All logos, brands and product names are trademarks or registered trademarks of their respective owners and are hereby recognized as such.

Disposal

|

This symbol indicates that this product should not be thrown away with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, you are responsible for recycling it so that it can promote the sustainable reuse of raw materials. To return your used product, you can use the regular return and collection systems or contact the store where the product was purchased. They can recycle this product for the environment.

---|---

Declaration of Conformity

We, Nedis B.V. declare as manufacturer that the product WIFILS51CRGB from our brand Nedis®, produced in China, has been tested according to all relevant CE standards and regulations and that all tests have been passed successfully. This includes, but is not limited to the RED 2014/53/EU regulation.

The complete Declaration of Conformity (and the safety datasheet if applicable) can be found and downloaded via:

nedis.com/wifils51crgb#support

For additional information regarding the compliance, contact the customer service:

Web : www.nedis.com

E-mail: service@nedis.com

Phone: +31 (0)73-5991055 (during office hours)

Nedis B.V., de Tweeling 28

5215 MC ’s-Hertogenbosch, the Netherlands