LEITNER LH280 On-the-Ear Wireless Headset Instruction Manual

LEITNER LH280 On-the-Ear Wireless Headset Instruction Manual

LH280

Understanding your…

HEADSET CONTROLS

WHAT’S IN THE BOX

• Headset
• Charging Base
• Lithium-Ion Battery
• Battery Door
• Replacement Ear Tips
• Foam Windscreen
• 8.5v AC Adaptor
• RJ-9 Phone Cord
• Type A-to-Mini USB Cord

CHARGING BASE

INDICATOR LIGHTS

AUDIO SIGNALS

When you walk out of range of the base, you will hear warning beeps in the headset.
If the headset disconnects due to being out of range, the call will not drop. The headset will automatically reconnect when you are back in range.

NOTE: If you do not move back in range within 5 minutes, the call will disconnect.

SET UP YOUR HEADSET

1 Plug the power adaptor into the charging base. The power light on the base will light up. We recommend charging your headset for at least 4 hours before use.

2a CONNECTING TO A TELEPHONE WITH A HEADSET JACK Use the included connector cord to connect the telephone port on the base to the headset port on your desk phone. You may need to adjust the compatibility switch on the bottom of the base to find the correct setting for your phone model. Most phones use 1. Cisco phones should be set to 4 only when using the headset jack.

2b CONNECTING TO A TELEPHONE WITHOUT A HEADSET JACK Connect
the curly cord of your handset to the handset port on the charging base. Use the included connector cord to connect the telephone port on the the charging base to the handset jack on your desk phone. See 2a on using the compatibility switch.

3 CONNECTING TO A LEITNER HANDSET LIFTER (OPTIONAL) Connect your
headset to your desk phone as shown in Step 2b. Attach the handset lifter to your desk phone and connect it to the AUX port on the charging base. Set the accessory selection switch on the bottom of the base to RHL. See the included user guide or go to headsets.com/LifterSetup for more help.

4 CONNECTING TO A LEITNER ELECTRONIC HOOKSWITCH (EHS) CABLE
(OPTIONAL)* Each office phone is a bit different so please refer to the EHS cable instructions for quick and easy setup.

With a handset lifter or EHS cable connected, you’ll be able to answer and end calls using the ON/OFF button on the headset—up to 350 feet away from your desk!

5 CONNECTING TO YOUR COMPUTER Use the included USB cable to connect the charging base to an available USB port on your computer. If your computer doesn’t recognize the device after a minute, go to your sound settings and select “DECT Headset” as both your default microphone and default speakers.

We’d love to help you get set up!
Call us at 1-800-432-3738, Monday through Friday 6:00am-4:30pm Pacific Time

MAKE A LANDLINE CALL

ANSWER A CALL

USE UNIBASE®

UniBase Technology allows you to conference your landline & softphone calls together!

Sounds from your computer will be shared automatically with the conference call

CONTROL YOUR VOLUME

ACTIVATE AUTO-ON

Turn this feature on if you’d like your headset to turn on automatically when you pick up your headset off the charging base.

To turn this feature on: With your headset turned off, hold the Volume Up button ( 1 ) and Volume Down button ( 2 ) on your headset together for three seconds. Once auto-on is activated, the light on your headset will flash slowly. To turn this feature off: Follow the same steps again. This time the light on your headset will quickly flash.

TURN ON CALL CONTROL

Your Leitner Headset can answer and end Skype for Business calls directly from your headset.

To turn this feature on: Hold the up button ( 4 ) on the bottom of your charging base together with the Computer Mode button on the top of your base for three seconds. Your base will quickly flash 6 times to confirm. To turn this feature back off: Hold the down button ( 5 ) on the bottom of your charging base together with the Computer Mode button on the top of your charging base for three seconds. Your base will flash 6 times to confirm.

CONNECT A SECONDARY HEADSET FOR

TRAINING OR CONFERENCE CALLS

5 If the secondary headset has Auto-On enabled, it will automatically connect when you lift it from the base. If it has Auto-On disabled, press the ON/OFF button ( 1 ) on the headset to connect.

NOTE: The secondary headset will remain registered to the base until the primary headset is turned off or if either headset is returned to its original base. It takes about ten seconds for the secondary headset to re-register to its original base.

Your LH280 can be conferenced with any on-the-ear Leitner headset

REGISTER A NEW PRIMARY HEADSET

In the event that you need to replace your headset, you’ll need to register the new headset to your charging base.

FREQUENTLY ASKED QUESTIONS

Q. I don’t have any battery lights on my headsets base and its been charging for
more than 4 hours
A. Start by unplugging the power to the headset base, then remove the battery from the headset for 30 seconds. Reinstall the battery making sure the Leitner logo is facing you. Plug the power back into your base. Press and hold the Telephone Mode button on the base until it flashes, then press and hold the Mute button on the headset until it flashes. Finally, place the headset next to the base (don’t place it in your charging base until the Telephone Mode light goes solid).

Q. My headset is charged and turned on but I can’t hear anything
A. If you set up your headset through the headset jack, make sure your telephone’s headset button is on. Check the compatiblity switch underneath your base is set to 1. Most Cisco phones should be set to 4.

Q. My headset turns on and the lifter goes up but I’m not hearing anything in the headset
A. Ensure that the charging base is connected to the telephone’s handset port and not the headset port (if the telephone has one).

Q. I can hear people on the phone but they can’t hear me.
A. Try adjusting the microphone volume from the controls underneath the charging base. Call us at 1-800-432-3738 and we’ll make sure you sound perfect!

Q. I can’t get my headset to work with my computer.
A. Make sure the USB cord is connected between your charging base and computer. If your computer doesn’t automatically recognize your headset, go to your computer’s sound settings and make sure DECT Headset is selected as your output and input device. Your sound settings can be found on most Windows computers by searching ‘sound settings’ in your search bar.

INSTRUCTIONS

It might seem a bit silly, but we’re required to tell you these safety instructions about your Leitner headset. Please keep these instructions for your reference. When using this product, these basic safety precautions and warnings should be followed to reduce the risk of fire, electrical shock, injury to persons, and damage to property.

Operating, charging and storage temperatures are 32 °F to 104 °F (0 °C to 40 °C).

General Warnings

• Never allow children to play with the product; small parts may be a choking hazard.
• Do not disassemble the product or AC adaptor as this may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock or fire when the product is subsequently used.
• Do not insert anything into the product because this may cause damage to the internal components or cause personal injury.
• Avoid contact with liquids. Do not locate this product near water, for example, near a bathtub, or sink, in a wet basement, or near a swimming pool.
• Discontinue use of product if the product overheats, has a damaged cord or plug, if the product has been dropped or damaged, or if the product has come into contact with liquids.
• This product should never be placed over or near a heat source and should not be placed in locations which do not have proper ventilation.
• If you experience skin irritation after using this product, discontinue use.

Charging Warnings

• Use only the charger provided with your headset to charge the product. Do not use the charger for any other purpose. Ensure that the voltage rating corresponds to the power supply you intend to use.
• Charge the headset according to the instructions supplied with the unit.
• Plug the AC adaptor or charger into an outlet that is near the equipment and will be easily accessible.

Headset Battery Warnings

• The headset is equipped with a replaceable battery. To reduce the risk of fire or injury to persons read and follow these instructions.
• Do not dispose of the battery in a fire. The battery may explode. Check your local laws for disposal instructions.
• Do not open or mutilate the battery. There may be corrosive materials which can cause damage to eyes or skin and may be toxic if swallowed.
• Never charge the battery where the temperature may fall below 32 °F (0 °C) or rise above 104 °F (40 °C).

RECYCLING: Your battery used in the headset must be recycled or disposed of properly. Contact your local recycling center for proper disposal of your headset battery.

To Protect Your Hearing

• Set the volume control in a low position before putting your headset on your ear and use as low volume as possible.
• Avoid turning up the volume to block out noisy surroundings.
• Limit the amount of time you use headsets at high volume levels.
• Turn the volume down if the sound from the headset prevents you from hearing people speaking near you.

For live product support
1-800-432-3738
Mon-Fri 6:00am-4:30pm Pacific Time
www.leitnerheadsets.com

Read More About This Manual & Download PDF:

References

• Leitner Wireless Headset Handset Lifter Setup for Phones
• Premium Lifetime Headset Help & Support | Leitner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>