Midea MWD-40P Floor Washer Instruction Manual

: June 5, 2024
: Midea

Table of Contents

Midea MWD-40P Floor Washer
Safety Instructions
Product Introduction
- List of accessories
Product Introduction
Use of Product
Troubleshooting
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Midea MWD-40P Floor Washer

Midea-MWD-40P-Floor-Washer-

Safety Instructions

This product is suitable for hard floors in the indoor home environment, including waxed, stone, rubber, marble, granite, terrazzo, solid wood, laminate, bamboo floors and various mirror tiles, porcelain tiles and other flat surfaces. The product may not reach the best performance on uneven surfaces.
Do not use this product near or on surfaces that are flammable or explosive, which may lead to a risk of fire and explosion.
Do not use this product near a working fireplace or heater to prevent deformation of the casing.
Do not suck in hot substances (unextinguished cigarettes, matches or hot ashes, etc.), ultra-fine substances (such as lime, cement, wood chips, gypsum powder, ashes, charcoal powder, etc.), hazardous substances (such as solvents, descaling agents, etc.), chemical substances (such as acids, cleaning agents, etc.), and other substances with uncertain physical properties.
Do not use this floor washer to suck up detergent, kerosene, gasoline, alcohol, paint, perfume, etc. These liquids may cause a short circuit, fire or explosion in the machine. Do not use this floor washer to suck toners used in laser printers and copiers, which may cause fire or explosion.
Do not use this floor washer to suck up sharp or large objects such as glass fragments, small toys, pins, paper clips, stones, plaster, large pieces of paper, which may jam and damage the machine.
Do not use the floor washer to suck up any burning or smoking objects, such as ashes from unextinguished heat sources, burning cigarette ends or matches, etc. Stains such as shoe polish, paint and pigments that are strongly greasy, sticky or stained shall not be cleaned using this device.
Do not touch the plug or any live part of the product with wet hands to avoid electric shock.
If the plug is damaged, do not use it any longer. Please call our professional maintenance personnel to replace the damaged plug to prevent hazards.
Keep the airflow channels and moving parts of this product away from long hair, loose clothing, fingers and other body parts. Do not point the vacuum hose, attachment wand or tool at your eyes, ears, or put them in your mouth.
Please use the cleaners made by our company and our approved manufacturers, and do not add other solutions to avoid toxic and harmful gases.
When using the device, in case of current leakage or over-temperature or noise of the motor, as well as other abnormal conditions such as body overheating, noise, odor or weak suction, you should immediately stop using the device and call our professional maintenance personnel.
After using the device, please clean up the sewage bucket in time to avoid odor and keep the ventilation path open to avoid blockage causing a decrease in suction power and motor heating, thus affecting the service life of the floor washer.
After using the machine, please keep it in a dry place. Humidity will affect the insulation and service life of the machine. The floor washer body and floor brush have energized settings and cannot be soaked or rinsed in water.
Please check the condition of the nozzle regularly. If there is any blockage, please clear it in time to avoid the decrease of suction power caused by the blockage, affecting the performance of the machine.
Make sure to turn off the machine before replacing the rolling brush.
In case of any of the following conditions, please don’t use the machine and send it to the service store assigned by our company:
1. The cleaner has fallen from a high place, leading to obvious damage or operation failure.
2. The power cord is damaged.
Do not disassemble the closed machine by yourself. There are no parts in this machine that can be repaired by customers themselves. Do not try to modify the performance of the machine, otherwise it will lead to danger.
The use of voltage that does not meet the specifications of the product will damage the product and may cause injury to the user.
When sweeping stairs, extra care should be taken to prevent falling.
Do not shake the machine up and down or bump it violently to prevent sewage from flowing into the motor.
When the motor is working, do not lift or carry the machine up and down, and do not put the machine to one side or flat to prevent sewage from flowing back to the motor.
To prevent tripping and falling, the machine should be placed against the wall after using it. Do not use the machine if the fresh water tank and sewage tank are not properly installed. Do not place any small objects on the air outlet, do not block the air outlet, and remove any small objects that may hinder the smooth airflow of the air outlet to prevent the machine from overheating.
Do not get the machine body wet, otherwise, there is a risk of fire due to a short circuit of the machine.
All technical and other data contained in the Use Instructions is obtained by our company or a designated third-party testing company. The final interpretation right belongs to our company

Product Introduction

Introduction to Parts

List of accessories

Midea-MWD-40P-Floor-Washer-
fig-2

Product Introduction

Accessories Introduction

Cleaning brush
- A brush at one end, can be used to clean the stubborn dirt attached to the inner wall of the sewage tank.
- The other end is a rotating blade that can be used to clean the tangled hairs on the rolling brush.
Cleaning spoon
- The cleaning spoon has a folding extension handle, which can be unfolded for use when needed according to the illustration;
- It can be used to filter solid waste such as particulate matter and hair.
Accessory holder
- It can be used to store rolling brush, cleaning brush and Hepa;
- Insert the projection part of the accessory holder into the slot of the charging base to fix it (there are slots on both sides of the charging base for fixing the accessory holder)
Cleaning liquid
- To carry out depth cleaning, just put cleaning liquid into the water tank after it is filled with water according to the specified proportion.

Use of Product

Installation of the handle
Insert the end of the handle into the port of the host vertically to the bottom position until a click could be heard. Pull it again to ensure that it could not be removed and that the handle is firmly connected to the machine body. Then the installation is successful.

Charging the machine

Notes
Charge the product before using it for the first time.

Insert the charging end of the adapter into the rear port of the charging base and connect the plug to the power supply.
Put the whole machine upright on the charging base to start charging, then there will be a voice prompting “start charging”, while the screen shows the charging power.
It will take about 4-6 hours to fully charge the machine, and the screen turns off after the battery is full, while the machine is automatically powered off.

Fresh water tank filling

Hold the body of the machine with one hand, and grab the upper cover of the freshwater tank to take it out of the machine vertically.
Remove the upper cover of the freshwater tank and fill the tank with tap water.
To carry out depth cleaning, just put cleaning liquid into the tank after it is filled with water according to the specified proportion
Screw the top cover of the water tank to ensure that it is closed tightly.
Install the fresh water tank back into the machine in the direction indicated by the printed words “this side facing forward” until the sound of click is heard.
In case of water shortage of the freshwater tank, there will be a sound prompt.

Turning on and cleaning

After the machine is fully charged, remove it from the charging seat, step on the ground brush and pull the handle diagonally and rotate the machine until the click sound is heard, at which time the machine enters the standby working state;
Start working: press the switch button to turn on the machine, and press this button again, the machine stops working.
1. Mode switching: the whole machine starts in the automatic mode by default. Press the mode switch button, the machine will be switched to rapid suction mode, press this button again, the machine will be switched to automatic mode.

Note

Automatic mode: the machine pump will work to wet the rolling brush lint for floor washing;
Rapid suction mode: the machine pump will not work, and the machine can suck the residual water on the floor in a dry or rapid way;
After using the machine, it is recommended to put the machine vertically on the charging base provided for your machine.

Vertical switch
The machine is equipped with a vertical switch and it can rotate upright until the click sound is heard. Then the machine stops running and is in standby mode. After standing by for one minute without operation, the machine will be shut down.

Self-cleaning function
After putting the machine onto the charging base, make sure that the machine is in charging state. After stepping on the charging base pedal with your foot for 2 seconds, the self-cleaning function will be started. After the self- cleaning is finished, please clean the sewage tank in time. If there is residual stain on the base, please clean it in time.

Cleaning of sewage tank

Notes

After cleaning, it is recommended to put the machine upright on the charging base at a place without direct sunlight or moisture;
In order not to affect the performance of the machine, the components of the machine shall be maintained regularly;
Before cleaning the machine, please cut off the power supply to stop its operation;
Clean the machine with water or neutral detergent, dry the cloth before washing the machine, and do not let the water get into the electrical components of the machine.

Hold the machine with one hand, and pull the sewage tank button outward with the other hand to remove the sewage tank;
Hold the machine with one hand and pull the upper cover of the sewage tank upward;
As shown in the figure, pour out the sewage from the side of the tank, and if there is solid-liquid mixed waste in the tank, it is recommended to remove the cleaning spoon at the back of the sewage tank to filter the particles and hair. If there is still solid waste left in the sewage tank after cleaning, rinse and filter the tank repeatedly, or unfold the extended handle of the cleaning spoon and stick the cleaning spoon into the sewage tank for cleaning;
Pour out the sewage from the side of the tank as shown in the figure, and if you find any stubborn dirt on the inner wall of the tank, please clean it directly with a cleaning brush;
Remove the Hepa from top of the sewage tank.
After taking the Hepa out of the tank, clean it with fresh water, dry it completely and then install it back to the sewage tank.
After removing the sewage, install the sewage tank back to the machine until the click sound could be heard.

Cleaning of the ground brush cover

Notes
After using the machine, wash the ground brush cover regularly to keep the machine tidy and clean.

After using the machine, wash the ground brush cover regularly to keep the machine tidy and clean.
After taking it out, wash it with fresh water until it is clean;
After cleaning, align the snaps at both ends of the floor brush cover with the slots at both ends of the floor brush, rotate and press the lift handle of the floor brush cover until a click sound is heard, and the installation is successful.

Cleaning of rolling brush

Notes

If residual stains are found on the mouth of the suction nozzle, wipe with a damp rag,
and do not rinse it with water;
After using the machine each time, clean and dry the rolling brush timely to keep it clean
and tidy.

Pull the handle on the left end of the rolling brush to remove the rolling brush.
Remove the rolling brush, open the rotation blade of the cleaning brush to remove the things tangled on the brush such as hair.
Remove the rolling brush, open the rotation blade of the cleaning brush to remove the things tangled on the brush such as hair.
Remove the rolling brush, open the rotation blade of the cleaning brush to remove the things tangled on the brush such as hair.