milwaukee M12 T LED LED Work Light User Manual
- October 30, 2023
- Milwaukee
Table of Contents
milwaukee M12 T LED LED Work Light User Manual
IMPORTANT SAFETY INSTRUCTIONS
WARNING
READ AND UNDERSTAND ALL INSTRUCTIONS When using electric appliances, basic
precautions should always be followed, including the following:
WARNING
Do not charge non-rechargeable batteries.
Before using the work light, read this operator’s manual, your battery pack and charger operator’s manual, and all labels on the battery pack, charger and work Light.
- To reduce the risk of injury, close supervision is necessary when an appliance is used near children
WARNING
The lens gets very hot during use. To reduce the risk of burns, do not touch hot lens
- Store idle work light out of reach of children. Warm work lights can become hazardous in the hands of children
- Do not use outdoors
- Batteries must be recharged only with the charger specified by MILWAUKEE®. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
- Use work light only with specifically designated battery pack. Use of any other batteries may create a risk of fire.
- When battery pack is not in use, keep it away from metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.
- Maintain labels and nameplates. These carry important information.
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
- Cat. No: . M12 T LED / M18 T LE
- Volts: 12V / 18 V D
- Watts: 4 W / 3.7 W
- Charger Type: M18™
Use only MILWAUKEE® M12 or M18 Li-Ion battery packs
ADDITIONAL BATTERY SAFETY RULES
WARNING
To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
WARNING
Do not charge non-rechargeable batteries.
SYMBOLOGY
Warning
Volts
Direct Current
Read Operator’s Manual
Indoor use
Do not stare into light
Class III protection
Regulatory Compliance Mark (RCM). This product meets applicable regulatory
requirements.
Do not dispose of electric tools together with household waste material.
Electric tools and electronic equipment that have reached the end of their
life must be collected separately and returned to an environmentally
compatible recycling facility.
FUNCTIONAL DESCRIPTION
ASSEMBLY
WARNING
Recharge only with the charger specified for the battery. For specific
charging instructions, read the operator’s manual supplied with your charger
and battery.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery pack into the body of the tool. Insert the battery pack until the battery latches lock. To remove the battery pack, press in both battery latches and slide the battery pack off of the tool.
WARNING
To reduce the risk of injury, do not look directly into the light when the
work light is on.
Adjusting the Pivot Head
M 2 LED – The pivot head can pivot to a range of 90°; with detents every 15°. Pivot head to desired position. Allow the detent to snap into place. Do not forcibly pivot the head.
M18 T LED – The pivot head can pivot to a range of 135°; withdetents
every 10°. Pivot head to desired position. Allow the detent to snap into
place. Do not forcibly pivot the head.
OPERATION
To turn on the work light, press the ON/OFF button. To turn off the work light, press the ON/OFF button again.
Hook M18 T LED
To use the hanging hook, press in the hook joint. Pull the hook out.
MAINTENANCE
WARNING
To reduce the risk of injury, always unplug the charger and remove the
battery pack from the charger or tool before performing any maintenance. Never
disassemble the tool, battery pack or charger. Contact a MILWAUKEE® service
facility for ALL repairs.
Maintain Work Light
Keep your work light, battery pack and charger in good repair by adopting a regular maintenance program. If the work light does not work properly, return the work light to a MILWAUKEE® service facility for evaluation and repair.
Cleaning
Keep tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean the tool, battery pack and charger since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include petrol, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools.
ACCESSORIES
WARNING
Always remove battery pack before changing or removing accessories. Only
use accessories specifically recommended for this tool. Others may be
hazardous.
For a complete listing of accessories, refer to your MILWAUKEE® Electric Tool catalogue or go online to milwaukeetool.com.au / milwaukeetool.co.nz or contact a distributor. To obtain a catalogue, contact your local distributor or a service centre.
WARRANTY – AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to product sold by authorised dealers in Australia and New Zealand.
SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE® prides itself in producing a premium quality product that is Nothing But Heavy DutyTM. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, please contact your authorised MILWAUKEE® dealer.
For a list of MILWAUKEE® dealers, guarantee or service agents please contact
MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928)
or visit
milwaukeetool.com.au/milwaukeetool.co.nz.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
26 – 40 Nina Link, Dandenong South,
Victoria, 3175, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN CHINA
PRINTED IN CHINA
References
- Milwaukee Tool | Official New Zealand Site of Milwaukee Tool | Nothing but HEAVY DUTY®
- Milwaukee Tool | Official Australia Site of Milwaukee Tool | Nothing but HEAVY DUTY®
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>