ATEN CE100 USB VGA Cat 5 Mini KVM Extender User Guide
- June 5, 2024
- Aten
Table of Contents
CE100
USB VGA Cat 5 Mini KVM Extender
(1280 x 1024 @ 100 m)
Quick Start Guide
© Copyright 2022 ATEN® International Co. Ltd.
ATEN and the ATEN logo are registered trademarks of ATEN International Co.,
Ltd.
All rights reserved. All other trademarks are the property of their respective
owners.
Part No. PAPE-1285-323G
Released: 06/2022
Package Contents
1 CE100L Mini USB KVM Extender (local unit)
1 CE100R Mini USB KVM Extender (remote unit)
1 USB / VGA cable
1 power adapter (remote unit only)
1 mounting kit
1 user instructions
Requirements
Consoles
- A VGA, SVGA, XGA, SXGA, UXGA, WUXGA, or Multisync monitor capable of the highest resolution that you will be using on the installation
- A USB keyboard
- A USB mouse
Computers
The following equipment must be installed on each computer that is to be
connected to the system:
- A VGA, SVGA, XGA, SXGA, UXGA, WUXGA, or Multisync card
- USB host controller and a USB Type-A port
Cables
- Use the USB / VGA cable supplied to connect the components on your installation.
- Cat 5e cable is the minimum required to connect the local and remote CE100 units. The cable of a lesser standard will result in degrading the video signal. For best performance, we strongly recommend using a Cat 5e cable.
Hardware Overview
CE100L / CE100R Top View
- power LED
- link LED
CE100L Front View
- VGA in
- USB Type-B port
CE100R Front View
- VGA out
- USB keyboard port
- USB mouse port
CE100L / CE100R Rear View
- power jack
- remote I/O
CE100L Side View
- grounding terminal
CE100R Side View
- video compensation tuner
- grounding terminal
Installation
Mounting
For convenience and flexibility, the CE100L and CE100R can be wall-mounted or
rack-mounted on a system rack.
- Using the screws provided in the mounting kit, screw the mounting brackets into the bottom unit as shown in the diagram.
- Screw the brackets into any convenient location on the wall or rack (these screws are not included).
Connecting the Cables
Setting up the Mini USB KVM Extender system is simply a matter of plugging in
the cables. Refer to the installation diagram (the numbers in the diagram
correspond to the numbers of the steps), and do the following:
- Use the USB / VGA cable provided to connect the CE100L to a USB / VGA port on the local computer (or KVM switch).
- Plug the remote keyboard, monitor, and mouse into their respective ports on the CE100R.
- Use a Cat 5e cable to connect the local unit’s (CE100L) I/O port with the I/O port of the remote unit (CE100R).
- Plug the power adapter supplied with this package into an AC source, and plug the adapter’s cable into the CE100R’s power jack.
Note: The CE100L doesn’t require a power adapter, since it gets its power over the USB / VGA connection.
Operation
- Use the keyboard, monitor, and mouse at the remote location to operate the computer at the local site.
- Adjust the video quality of the display at the remote location with the Video Compensation Tuner.
Support and Documentation Notice
All information, documentation, firmware, software utilities, and
specifications contained in this package are subject to change without prior
notification by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and
software can be found online at
http://www.aten.com/download/
Technical Support
www.aten.com/support
Scan for more information
ATEN Website
https://www.aten.com/global/en/products/modelno/ce100/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>