Pulumo Art Drone Drone with 4K Camera User Manual

Pulumo Art Drone Drone with 4K Camera

Statement and safety guidelines

When you use this statement, it means that you agree to this statement and that you have read the statement in its entirety.

1. Before flying, please practice with a simulator, or seek professional guidance.
2. Do not fly above or near obstacles, crowds, open water, public roads, high voltage lines or trees
3. Do not use drones in severe weather conditions such as rainy or windy (wind sppeed is greater than 7.9m/s), snow, hail, lightning, tornadoes, hurricanes, etc.
4. Do not fly drones in electromagnetic, radio zones, and government-regulated no-fly zones.
5. Fast rotating engines and propellers are a potential hazard to cause serious damage and injury. When the drone is operating, a safe distance of 5 meters must be maintained at all times.
6. Always keep the sight of the drone after turning on.Don’t rely on the camera image to control your drone.
7. This product is not a toy and is not recommended for users under age 14.
8. This product is not suitable for professional UAV aerial photography.
9. All parts must be placed out of the reach of children to avoid the danger of suffocation.
10. Note: Handle drones and batteries according to local regulations.Don’t treat it as domestic garbage.
11. Ensure compliance with all local regulations, obtain proper authorization and understand the risks.

Please note that it is your responsibility to comply with all flight rules. PULUMO is not responsible for any damages, injuries or any legal liabilities arising directly or indirectly from the use of this product. Users should follow safe and legal practices, including but not limited to the practices specified in this disclaimer and safety guide. PULUMO reserves the right to update this user manual.

Maintenance

1. After a crash or violent impact, thoroughly inspect the drone.
2. Clean your drone with a dry cloth to prevent any moisture from entering the electronic equipment.
3. Please do not disassemble or repair the product by yourself, if necessary, please contact with PULUMO.
4. If you do not use it for a long time, please remove the battery from the drone
5. Please store and charge in a cool and dry place (0-40℃ ). Do not place the battery in an extremely high temperature environment that may cause explosion or leakage of flammable liquid or gas.
6. Please use the original battery provided. Using the wrong model or battery may cause a fire hazard.
7. Do not charge when the battery is hot. Let it cool first.
8. Only use the original USB cable provided. Do not overcharge the battery. Once the battery is fully charged, please unplug the charger.
9. Do not charge near flammable materials such as beds, carpets, wooden floors, or conductive surfaces.
10. Do not leave the battery unattended while charging.
11. Keep the battery away from any sharp objects that may pierce the battery to avoid the danger of explosion and fire.
12. Do not put the battery in a fire or a high-temperature oven, and do not cut or mechanically crush the battery to avoid explosion.
13. Do not drive nails, hammer or step on the battery. Do not use other methods to knock the battery.
14. Do not disassemble or change the external structure of the battery.
15. Do not expose the battery to extremely low air pressure, as this may cause an explosion or flammable liquid or gas leakage.
16. When the battery power is low, do not store the battery for a long time. In order to prolong the service life of the battery, if it is not used for a long time, charge it at least once every three months.
17. If the battery is swollen, please replace the battery.

Telecontroller

1. Photo/video: the wheel up to take photos, the wheel down to turn on / off video
2. Flight mode switch: switch GPS mode and optical flow mode
3. Left rocker: to control the flight height and nose direction of the UAV
4. Unlock: click to unlock/lock
5. One-key/start-off: click one-off / one- key landing
6. Display screen: display the data of the drone during flight
7. Speed adjustment: Click to adjust the flight speed at the low / medium / high speed of the UAV
8. One-click return: Click the drone to enter the return mode and automatically return to the recorded take-off point
9. Headless mode: Click on/off headless mode
10. Switch: Turn on and power off the remote control
11. Right rocker: control the front and rear/left side of the drone
12. Mobile phone bracket: Install the mobile device
13. USB charging port: remote control charging port

Flight preparation

1. Unfold the front arm first, then unfold the rear arm.

2. Battery charging
   battery power indicator flashes when charging, battery power indicator lights on after full.5V/1-2A.（Charging time is about 180 minutes） Note: Please do not charge when the battery temperature is too high

3. 3.Install the fully charged battery to the drone

4. Insert a memory card into the drone (FAT32 format, within 32G)

5. Charging the remote control
   (the red indicator lights on when the remote is charged and off when it is fully charged.5V/1-2A.The charging time is about 120min)

6. Unfold the remote control

7. Mobile device installation

Flight Operation Guide

It’s important:
Make sure you energize the drone first, then the remote control for each flight.
Repeat the pairing process every time the drone or remote server restarts. For all flight functions and modes, the operator and the drone tail must be aligned.
We recommend beginners to fly outdoors and within the co ntrol range. Use the remote control and App to control the drone at the same time to get a better flying experience.

Remote control and drone pairing steps

1. Turn on the remote control switch
   Note: The remote controller needs to be restarted every time the drone is restarted

2. Unfold the drone’s arm, place the drone on a horizontal surface, and press and hold for three seconds to turn on the drone’s battery switch.

3. The remote control beeps once, and the pairing is complete

Calibration

Compass calibration
Open the mobile APP, enter the operation interface, click (icon) to open the calibration interface, and click (icon) to calibrate the compass. Rotate horizontally 3 times, the remote control beeps. Rotate vertically three more times, and the remote control will make a beep. Calibration is complete.

icon: Horizontal calibration
Place the drone on a horizontal surface, hit the left and right joysticks
of the remote control to the lower right corner, and the drone indicator light flashes quickly. After the fast flashing ends, the level calibration is completed (or click the level calibration in the APP operation interface)
Note: Keep away from magnetic objects and electronic equipment during calibration

GPS Satellite Search
Wait for the drone to search the GPS satellite, after the search is complete, the remote control will make a long beep. (the remote display shows the number of GPS searched, we recommend GPS satellites larger than 10 before flying)
The drone is set to GPS mode by default.In this mode, the drone can use the GPS module to locate itself and perform precise hover flights.
The GPS mode works when the GPS signal is strong.Please fly the drone outdoors. We strongly recommend beginners to use this mode. The drone is in GPS mode.It cannot take off until searching for a GPS that satisfies the localization if the GPS mode is not available. Please fly the drone to outdoor locations where the GPS signal is strong. If you want to fly indoors where GPS mode is not available, switch to light optical flow mode.

Note : When the GPS satellite search is complete, the remote control makes a long beep sound.

Optical flow mode

Long press the GPS button in the upper left corner of the remote control, the remote control beeps twice, and the upper left corner of the remote control display shows GPS OFF and the drone enters the optical flow mode. Long press the GPS button again, the remote control beeps, and the drone returns to GPS mode
Note : The drone is not allowed to manually switch between GPS mode and optical flow mode while flying

Flight operation

1. Click the remote control to unlock the button, the drone propeller begins to rotate, the left hand rocker forward to push the drone altitude.(Or click on the one-click take-off button.The drone automatically takes off to an altitude of about 1.5 meters.Click one button take-off button again drone to ground)
2. Note: Click the unlock button again after unlocking, and the drone propeller will stop rotating

Flight Directions

Left Control Stick

• Push the Left Control Stick forward and the drone will ascend; pull it backward and the drone will descend.
• Pull the Left Control Stick leftward and the drone will rotate to the left; pullit rightward and the drone will rotate to the right

Right Control Stick

• Push the Right Control Stick forward and the drone will fly forward; pull it backward and the drone will fly backward.
• Pull the Right Control Stick leftward and the drone will fly leftward; pull it rightward and the drone will fly rightward.

Return back

1. If the GPS signal shows more than 10 and the compass function is normal, the homing function will bring the UAV back to the homing point of the uav take-off recorded last time. Otherwise. This function cannot be executed.
2. Press the one-click return button of the remote control to start the intelligent return. The drone returned to its last recorded point of return.

When the current distance from the recorded return point is more than 20 meters and the height is less than 30 meters.The drone will be raised to 30 meters to return home.When the current altitude exceeds 30 meters, the drone will return home at its current altitude.When the drone’s current distance from the return point is less than the recorded return point of 20 meters, the drone will return directly from its current altitude.When the remote control swing lever is controlled, the return trip is suspended.After releasing the rocker, the drone continues to perform the return command

Uncontrol protection
When the remote control is disconnected from the drone for more than 3 seconds, the drone will automatically activate the fail-safe protection. under the control of the flight control system and return to the recorded take-off point.When the remote control reconnects with the drone, the out-of-control protection will automatically stops and the drone will hover in its current position.
Note: The drone cannot avoid obstacles in the return flight path.
When the remote control is disconnected from the drone and more than 3 seconds,GPS is not available, the drone will slowly descend from the current altitude until it lands. .

Low power protection
When the drone battery is low and the distance exceeds 20 meters or the altitude exceeds 30 meters. The drone will automatically return to a horizontal distance of 20 meters and a height of 30 meters or less. It is not possible to fly beyond this distance again after returning. When the drone battery is severely low, the drone will directly return to the takeoff point from the current altitude.
After landing, the drone cannot take off again. Please replace or recharge the battery in time

Take photos / videos
Move the upper left corner of the remote control upward to take a photo, move it down to start recording, move it down again to stop recording
Note: Photos cannot be taken during the video recording

Head-free mode
Press and hold the button for more than 1s to activate the headless mode.In this mode, the drone will fly in the direction of the right joystick, regardless of your drone’s head or tail position.Repeat again to cancel this mode.

Speed adjustment
Short press the speed adjustment switch, the remote control beeps twice, and MH is displayed on the left side of the remote control display. At this time, it switches to medium speed. The remote control beeps three times, the left side of the remote control display shows RH, and it switches to high speed at this time. Short press the button again, the left side of the remote control display shows LH, and it returns to low speed.
Note: The drone is in default low-speed mode

One-click take-off/landing
After the drone is unlocked, briefly press the one-button takeoff/landing button.The drone will automatically take off to about 1.5 meters to hover, press and hold the one-button take-off / landing button above 1S again, the drone will automatically land.
Note: Hovering requires GPS or a visual positioning system to meet positioning requirements (GPS meets positioning requirements: GPS signal number shows more than 10. The visual positioning system meets positioning requirements: the ground is sufficiently illuminated and the texture is clear. Glass, solid- color ground, highly reflective ground, water surface the visual positioning system cannot be satisfied. When the drone is 20 meters away from the recorded take-off point, the one-key landing will not respond)
Note: When the GPS mode meets the requirements of positioning, press th e unlock key for 5s, and the remote controller drops a beep to remove the electronic fence.The remote control display shows U/D  (The default horizo ntal distance of the electronic fence in GPS mode is 500 meters)

Software Operation  Guide

App to download and install

Download and install PULUMO ART to your mobile device, App Store/ Google Play, or scan the QR code below the illustrating picture

Application startup steps

1. Enter the Wifi settings for the mobile device and connect to the Wifi,Pulumo-art-xxxxx x.Step
2. Open PULUMO ART, click “GO FLY” to App.

Note: If you do not have Pulumo-art-xxxxx x wifi, in your wifi list or preview images in your App, restart the drone and remote control, repeat the pairing and calibration program.
Make sure that the Pulumo-art-xxxxx xwifi is connected to only one mobile device.

If you can’t see the real-time map, disconnect the drone from its Wifi, and then turn on the cellular data and location services on your mobile device to preload the map.Next, turn off the phone data, reconnect the drone’s Wifi, and then launch the app.
The drone’s Wifi could not access the Internet.It is recommended that you turn off the phone data when you connect to your drone’s Wifi. Otherwise, your mobile device may automatically switch to cellular data and disconnect from the drone’s Wifi.

APP interface description diagram

Calibration

Click (icon) to perform the gyroscopic calibration and compass calibration.
Compass calibration: click on the calibration and then the (icon) will appear, follow the prompts to rotate three times horizontally and rotate three times vertically to calibrate.
Gyro calibration: After placing the drone on the horizontal ground, click on the calibration
Note: Stay away from the magnetic interference source during pin calibration.Do not move the drone during the gyroscope calibration.

icon: One- click take-off / landing

1. One-click takeoff: After the remote control click (icon) unlock button, the drone propeller rotates.At the APP click (icon), click to confirm the take-off, the drone will automatically take off to an altitude of about 1.5 meters
2. One-click landing: When the drone clicks (icon), the drone will automatically land in place
   Note: When the GPS meets the positioning situation, the function no longer responds after the horizontal distance is 20 meters beyond the take-off point recorded by the drone.

Go home with one click

Click (icon) and the drone enters return mode and automatically return to the recorded take-off point
Note: The return function needs to respond if the GPS signal is good and the compass is healthy

icon:

Function menu
Click close or open function options

Reverse the lens
Click on the lens screen to flip over for 180 °

3D three-dimensional
Click to open the VR mode

Multi-flight
Click to open point flight (Inside the red circle on the map,When the navigation function is executed, the mode can be controlled by any rocker  )

Follow
Click on to open the follow me

Point of interest surround
Click to open the surround of interest point, and control the direction and speed of the surround by the left and right of the right rocker of the remote control

Gestures to shoot
Click to open the gesture shooting function, and aim the gesture at the center of the front camera of the UAV. After recognition, the UAV takes photos/videos (the best recognition distance is about 2 meters, gesture recognition function runs on the APP, recognition success rate is related to the mobile phone operation rate)

Flight record
Click to view the drone flight records recorded by the APP

Lens switch
Switch front camera and bottom camera

Add music
Click on the music addition function to record a video with background music.

Posture ball
Click to open the map

Flight data
Displays the current flight altitude, distance, speed and speed of ascent and descent

Magic stick
Click to add a filter for the live screen

Amplification and narrowing
Click to zoom on the real-time screen (up to 50 x electronic zoom, or double fingers to hold the screen for zoom)\

Microphone
After clicking, turn on the phone microphone for recording, and you can put the recorded sound into the video being recorded.

Preview
Click to enter the media library to browse through the photographed media files

Shoot the switch
Click to shoot

Photo/video switch
Click to switch to the shooting switch and switch to the photo/video mode

Main interface
Click to return to the main interface

Flight record
Click to browse through the drone’s flight record

Status bar
Displays the current flight mode

Answer frequently questions

1

| The drone’s motor does not rotate.| Please make sure you have the drone and remote on.

Please make sure the drone and remote control batteries have enough power.

Please make sure the remote control is

successfully paired with the drone.

2

| The drone indicator l i g h t f l a s h e s abnormally| Please make sure the drone battery has enough power.

Please try calibrating the compass and the gyroscope.

3

| After I turned on the motor, the propeller of the drone began to rotate, but the drone could not take

off.

| Please make sure that the drone battery has enough power.

Please make sure the current flight mode is

correct.

4

| After unlocking the motor, push the left control lever drone forward to tilt aside.| Ensure that the propeller (A / B) is installed correctly

Check the consistent motor speed.

Check that the motor is stuck in small objects.If so, please take off the small

object

5

| T h e d r o n e f l o a t s

after takeoff

| Ensure GPS mode is on and has a strong GPS signal.

Please let the drone land and recalibrate the

compass.

6

| The drone does not respond or is insensitive to the control of the remote

control.

| Make sure the drone flies under control. Switch the drone’s speed to medium or high speed

Make sure that the remote battery has

enough power.

7

| Cannot see a real- time image on the App.| Make sure the drone has enough energy.

Make sure that your mobile device is

connected to the drone’s wifi.

Go to the mobile device settings, turn off the phone data, or turn off the phone’s ability to automatically disconnect without network access.

Make sure that the camera is not blocked. Make sure the drone flies within the FPV range

Please try connecting wifi using other

phones

8

| After the drone was inserted into the memory card, the shooting media file was not found in the memory card| Please format the memory card

Make sure that the memory card is in FAT32 format

Make sure that the memory card is inserted correctly

---|---|---

Parameter Table

Drone

Operating Temperature| 32˚ to 104˚F ( 0 ℃ to 40℃ )
Frequency Range| 5150-5250 MHz
Transmit Power| 5GHz
Battery| 7.4v 2200mah 16.28WH
FOV| 120˚

Warning

Careful If the replaced battery type is incorrect, there is a risk of explosion, follow the instructions for handling used batteries with symbols indicating DC voltage
Recycling this product with a (WEEE) selective sorting sign. This means that the product must be treated in accordance with the European Directive 2012 / 19 / EU to recover or dismantle it to minimize its environmental impact.
When users purchase new electrical or electronic equipment, they have the option to hand the product to a competent recycling agency or retailer.
The product can be used in the EU Member States to meet the requirements of RF exposure.
The battery must be recycled or properly handled
CompanyName : Shenzhen Buying Technology Co., LTD
Company address : Room 507, Zongtai Future City, No.2003 Taoyuan Road, Shenzhen ( zip code: 518000 )

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>