Custom Accessories 23209 APP Driven 1 Channel RGB LED Bed Light 8PK Kit Instruction Manual
- June 6, 2024
- Custom Accessories
Table of Contents
Custom Accessories 23209 APP Driven 1 Channel RGB LED Bed Light 8PK Kit
Instruction Manual
8Pc EXTERIOR LED BED LIGHT KIT
23209 Installation Instructions
Kit Includes:
WARNING
- Never use the LED Innovation ™ App while driving and obey all traffic laws.
- This product is intended solely for the purpose of decorative or off-road use. Check laws and/or regulations in your state, county, and/or municipality regarding the installation and use of this product. This product is not DOT Approved.
- Do not install this product or run its wires near any moving parts. Keep all wires and lighting units away from excessively hot areas.
- 12 Volt use only. Product designed to draw up to 2.8 Amps.
BEFORE INSTALLATION
Download the App, connect to Bluetooth® and test your LED strip lights. Make sure you read the instructions carefully.
INSTALLATION INSTRUCTIONS
- Begin by laying out your new truck bed lighting kit. Place your LED pods where you’d like to install them. Insert the trailer plug into your trailer socket to make sure you have enough cable length.
- Next, select a mounting location for the control box while making sure you leave enough wire to reach both the LED pods and the trailer socket. Install your control box using the included two-sided 3M tape and screws. Before installing screws, pre-drill a 1/16″ hole.
- To install your LED pods, clean the surface thoroughly with alcohol and allow them to dry before installation. Next, remove the liner on the rectangular 3M tape strips and secure it to the LED pods. Then remove the liner on the other side of the 3M tape strips and stick your LED pods in position. To fully secure the LED pods, you may use the included screws. Before installing screws, pre-drill a 1/16″ hole.
- Tuck and secure all wires using the included cable ties.
- Start your vehicle. Open the LED INNOV APP and connect to the “EXT HUB” 1 channel system. The phone must be within Bluetooth range (approximately 30 feet from the control box).
- You have now successfully installed your new LED lighting and are ready to customize it using the LED INNOV APP.
- Please see the “Info” tab on your LED INNOV APP for more important tips and instructions.
ONE YEAR WARRANTY
We guarantee this product to be free of defects in material and workmanship for a period of one year from the date of purchase. If a defect in material or workmanship occurs, call Custom Accessories customer service at 800-962-6676 for instructions on how to have it replaced or repaired free of charge.
PROOF OF PURCHASE OR RECEIPTS MUST BE
PROVIDED FOR ANY/ALL REPLACED OR REPAIRED ITEMS.
This guarantee does not cover normal damage to the product that is not the
result of a defect in materials or workmanship such as, for example, normal
wear and tear or damage resulting from an accident. Shipment of any product
back to Custom Accessories is at the consumer’s expense.
Custom Accessories Inc. limits its liability only to the replacement of its
products, not incidental or consequential damages to other property. Some
states do not allow the exclusion or limitation of incidental or consequential
damages. This guarantee gives you specific legal rights and you may also have
other rights which vary from state to state.
For FCC matters, please contact:
Custom Accessories Inc., 5900 Ami Drive, Richmond, IL 60071
Phone: 815-678-1600
FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FCC Regulations:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the manufacturer or an experienced technician for help.
CAUTION:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the product. This
equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>