LINNER DTT15Z Soap Buds True Wireless Stereo Earbuds User Manual
- June 5, 2024
- LINNER
Table of Contents
User Manual
Soapbuds True Wireless Stereo Earbuds
Dear Valued Customer
Thanks for choosing this product!
In order to make full use of this item and avoid misuse,
please read the manual carefully before using it.
What’s in the Box
(The above pictures of accessories are for reference only)
Structure of Soapbuds
Instruction for wearing
Wearing earbuds and adjust the right angle as the picture shows. It’s OK when we feel comfortable and stable.
A closer microphone makes a crystal clear phone calls
Power on
Open the charging case, the earbuds will power on automatically and re-connect
to the phone that has been connected before.
Connecting Bluetooth of the mobile phone
The first step: The earbuds in the pairing mode
Method 1: For first use, open the charging case, the earbuds will power on
automatically and enter the pairing mode.
Method 2: When earbuds in the charging case, open the upper cover and long-
press the charging case button for 3 seconds until the white light flickers 10
times, earbuds will get into pairing mode.(a. during pairing mode, please keep
the charging case open until pairing successfully;b. the charging case white
light will be off after 10 seconds, but it will not affect pairing)
The second step: phone searching and connecting Turn on the Bluetooth function
of the phone to search Linner Soapbuds and then connect. It will show
connected successfully.
Notice:
- After earbuds are connected to a mobile phone, when you open the charging case, earbuds will connect to the last connected mobile phone automatically. If the last connected mobile phone is out of connection range or the Bluetooth function is not on, earbuds will get into searching status.
- The pairing mode lasts 10 minutes at most. Earbuds will power off automatically if they are not connected to any Bluetooth-enabled device during this period. If need to be connected again, please operate as “Power on” and “Connecting Bluetooth of mobile phone” steps.
- If out of the Bluetooth range, earbuds will disconnect with a Bluetooth-enabled device and will re-connect if back to the right distance within 10 minutes.
Power off
Method 1: Put the earbuds into the charging case, and close the upper lid, the
earbuds will be powered off automatically after 3 seconds(But if the charging
case runs out of power, the earbuds will fail to turn off and you need to
recharge promptly.)
Method 2: Earbuds will turn off when they run out of power.
Method 3: Earbuds will power off automatically if they are not connected to
any Bluetooth-enabled device within 10 minutes.
Siri Function
Triple-click will activate the Siri function and exit with the same operation.
Answering a Call
Double click either earbuds at the touching area
Ending a Call
Double click either earbuds at the touching area
Rejecting a Call
Keep touching either earbud for 2S.
Switching Phone Call between Earbuds and Mobile Phone
Keep touching either earbud for 2S
Music Playing
Play/Pause: Double click either earbud at the touching area Previous track:
Keep touching the left earbud for 2S Next track: Keep touching the right
earbud for 2S
Notice:
- 1f a phone call comes during music play, the earbuds will play music automatically after the call ends.
- Music will pause if using Sin and will re-play music automatically after exit Siri.
- If using only one earbud, the earbud can go next track only, and cannot go previous track by this operation.
Master-Slave Switch
Take out either earbud from the charging case, it can connect with a
Bluetooth-enabled device and be used as a wireless earbud independently. And
the other can be paired with it quickly anytime when taken out of the charging
case. When the master earbud runs out of the power or places the master into
the charging case, the slave will switch to the master automatically and keep
working.
Lights instruction
Earbuds are not fully charged, it will charge automatically when put into the
charging case.
- When earbuds are not fully charged, open the upper cover or short press the charging case button, the orange light will be off after 10 seconds.
- When earbuds are fully charged, open the upper cover or short press the charging case button, the green light will be off after 10 seconds
If earbuds are out of the charging case, it will show the battery status of the charging case when opening the upper cover.
- When the battery is over 50%, the green light will be on for 10 seconds.
- When the battery is between 10%-50%, the orange light will be on for 10 seconds.
- When the battery is under 10%, an orange light will flicker.
When earbuds are in the charging case, short press the charging case button, it will show the battery status of the charging case.
- When the battery is over 50%, the green light will be on for 10 seconds.
- When the battery is between 10%-50%, the orange light will be on for 10 seconds.
- When the battery is under 10%, an orange light will flicker for 10 seconds.
Earbuds lights instruction
Product Specification
Model #: | Soapbuds |
---|---|
Dimensions: | 16.5641.1717.49mm(earbuds. |
7339.1927mm(charging case | |
Bluetooth version: | V5.0 |
Transmission distance: | 10 meter |
Input Voltage: | DC 5V/1A |
Battery capacity: | 3.7V/35mAh (earbuds) |
3.7V/500mAh (charging case) | |
Working time: | 4H |
Charging time: | 2.5H |
Waterproof level: | IPX4 |
Factory Resetting
Step 1.
Put earbuds into the charging case and keep the case open.
Step 2.
Press and hold the charging case button for 10 seconds until the indicator
flashes green 5 times, and factory resetting is finished. All the pairing
history will be cleared off.
Safety Notifications
- Please use the products according to user manual. And please do not disassemble or modify the device for any reason. Or the earbuds may break down or burn.
- Do not drop the product to any liquid or wash it.
- Do not charge the earbuds with a charger that is over-voltage. Use the charger with a rated voltage and current of 5V/1A. Or it will damage the battery.
- Do not use or store the earbuds in an environment where the temperature is too high or too low (below 0 degrees or above 45 degrees.)
- Do not block the earbuds, such as the charging interface, LED indicator, or microphone.
- Do not use the earbuds over time and over volume. This may make you dizzy or be harmful to your hearing.
- Do not use the equipment in a thunderstorm environment. Thunderstorms may cause abnormal operation of the equipment, signal interruption, etc.
FQAs:
Entry | Handling method |
---|---|
How to re-match two earbuds together? | Put two earbuds into the charging case, |
press the charging case button 3 times continuously, until the white light
flickers 5 seconds and then off, that means two earbuds re-match successfully.
Connect earbuds to another mobile phone?| Put earbuds into charging case, long
pres charging case button for 3 seconds, the s indicator will flash white for
10 seconds, then the earbuds go to pairing mode, capable of connecting with
another phone.
The earbuds have no action or shut down.| Put earbuds into the charging case
and close the charging case for 10 seconds. Re-open the charging case and the
earbuds can work properly.
Distinguish master and slave.| The device supports master-slave switching. The
first earbud which turns on will be the master.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SHENGYUAN TECHNOLOGY (SHENZHEN) CO., LTD.
Address: Floor 19th- A, South Tower, China Academy of Science and Tech
Development Building,
No.9 Gaoxin South 1st Ave.
Nanshan District, Shenzhen
Customer service hotline: 400-0755-705
Official website: www.linner.com.cn
FCC ID: 2AMNM-LINNER
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>