SYLVANIA 65482 MOSAIC LED FLEXIBLE LIGHT KIT User Manual

: June 5, 2024
: SYLVANIA

Table of Contents

Package includes
SAFETY INFORMATION
Troubleshooting remote connection.
SETTING UP
Remote Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

65482 MOSAIC LED FLEXIBLE LIGHT KIT
User Manual

Package includes

(5) 2ft LED Light Strips (adhesive backs)
(1) RF Controller
AC/DC Adapter
(4) Connectors
Remote (battery included)
(6) Mounting clips (adhesive back)

SAFETY INFORMATION

Please read, follow and understand this entire manual before attempting to assemble operate or install this product. Save these instructions.
WARNING!

To avoid electrical shock or product failure this strip must be used in dry indoor environments.
This product is not a toy and is not to be stored or left in locations accessible to young children.
To avoid possible ﬁre, product damage, or early strip failure, this strip should not be used in heat-producing appliances.
To avoid possible ﬁre hazards, only connect a maximum of 10 strips for a length of 20 feet to a single AC adapter and Controller.
To prevent early strip failure, a strip should only be installed in operating environments ranging between 14°F to 104°F (-10°C to +40°C).
Choking Hazard: This kit contains small parts. Do not store or leave in a location accessible to young children or pets.
Uncoil ﬂexible light prior to plugging in.
Do not install near ﬂammable liquids.
Do not install where it may be stepped on, or subject to the physical damage.
Always unplug this product before installing, cutting the strip, or connecting to the power
Use only SYLVANIA LED Mosaic RGB+W Flex Kits when connecting additional strips and using connectors.
Not for use with phase cut dimmers.

CAUTION!

When not using this product for extended periods, remove the battery from the remote to prevent product damage due to battery leakage.
Observe proper polarity when charging the battery. The strip may not light if the battery is inserted incorrectly.
This product includes an AC/DC adapter (model 65482) that is not designed for seasonal use LED drives and non-integral LED lighting strings.

Troubleshooting remote connection.

If for some reason the remote does not connect to the strip’s controller, please re-pair it following these steps:

Turn off the power for about 5 seconds by disconnecting the power supply from the outlet.
Re-connect the power supply back into the outlet, and in fast succession, press the ON button on the remote 3+ times.
After the strip lights up with ﬂashing green and ﬂashes rapidly a few times, the remote has successfully been paired. If unsuccessful, repeat the process until the strip is paired.

SETTING UP

Please read, follow and understand this entire manual before attempting to assemble operate or install this product.
Save these instructions.

Once the ﬁnal mounting position has been determined, clean the surface to assure the self-adhesive backing will adhere properly. It is important that the mounting surface needs to be smooth, dry, and free from oils and waxes, in order for the strips to adhere to the surface correctly. For best results, apply the strip at a room temperature range of 68-86°F (20-30°C). The Mosaic strips can be installed on curved and irregular surfaces, but avoid sharp bends as the light strip could be damaged.
Measure the length of the area where the ﬂex strip will be placed. Each ﬂex strip is 2ft long. If the strip ends up being too long, shorten the end of the strip by cutting at one of the lines indicated by the scissors icon. Connect all the elements together and apply power to the ﬂex strip to test that the strip is working before mounting the ﬁnal product.
NOTE: Once cut, the section of ﬂex strip can no longer be connected to other ﬂex strips or the universal connector
NOTE: Can only connect a maximum of 10 strips for a length of 20 feet.
Use a connector if you are wrapping the light strip around any corner. The use of the connector will help prevent crimping or permanent damage to the light strip
Remove the protective layer covering the back of the ﬂex strip. Carefully place each strip in the ﬁnal mounting position as the adhesive is permanent and the strip cannot easily be moved.
Press the ﬂex strip ﬁrmly in place and hold it for 5 seconds so that the tape adheres to the mounting surface. Make sure each of the ﬂex strips is tightly connected to each other before continuing to mount.
Connect the controller to the ﬂex strip. Make sure that the arrow icon on the controller connector matches with the 12V+ marking on the connecting strip.
Connect AC/DC Adapter to the controller.
Plug the AC/DC Adapter into the power outlet.
To turn the strips on, remove the clear pull tab from the remote so the battery can make contact. Press the ON button on the remote to light up the strips.

Remote Instructions

Here are the commands that can be used with you ﬂex light remote:

3-YEAR LIMITED WARRANTY: LEDVANCE warrants the Product to be free from defects in materials and workmanship from the date of purchase for the specific warranty period when used as directed. Failure to comply with Product warnings and instructions shall void the warranty. This warranty does not cover Products subject to accident, neglect, abuse, misuse, or acts of God. If the Product fails to operate according to the warranty, return the Product to the place of purchase with proof of purchase date and LEDVANCE will replace it with the same or similar product for free. For additional information, contact 1-800 LIGHTBULB (1-800-544-4828); Email: lightbulb@ledvance.com. THIS IS THE EXCLUSIVE REMEDY AVAILABLE. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXPRESSLY EXCLUDED. SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.