SYLVANIA 63473 Wall Mount Lantern Instruction Manual

SYLVANIA 63473 Wall Mount Lantern Instruction Manual

PACKAGE CONTENTS

TOOLS REQUIRED (not supplied)

HARDWARE CONTENTS

Note: Hardware not shown actual size.

PREPARATION

Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.

⚠ SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING

• Turn off electricity at circuit breaker box (or main fuse box ) before beginning installation by removing fuse (or switching off circuit breaker).

• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
  CAUTION

• All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections.

• Risk of fire ­ most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician before installation.

• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper grounding methods as required by the local electrical code in your area.

• If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and electrical rating required.

• Operating Temperature between -20(-4) 40(104).

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications to this products will void the product warranty and could void the user’s authority to operate the equipment.

FCC Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information Responsible Party: LEDVANCE LLC
1100 Tyrone Pike Versailles ,KY 40383,USA
1-800-544-4828
Unique Identifier: 63473

ASSEMBLY INSTRUCTIONS

1. Turn Off Power.
   Before beginning the installation, make sure all power is off at the breaker box.

2. Removing the installation bracket
   Unscrew the mounting finials (DD) and washers (EE) from the fixture body (A) and remove the Crossbar Mounting Bracket (CC) as shown below.
   NOTE: Ensure to save the mounting finials (DD) and washers (EE) .

3. Installing Mounting Bracket
   Align the Crossbar Mounting Bracket (CC) holes to the junction box using the junction box screws (AA) and tight firmly.

4. Making the electrical connections
   Using the wire connectors (BB) provided , connect the black wire from the junction box to the black wire from the fixture, the white wire with white and the green from the fixture to the copper wire from the junction box.

5. Installing the fixture
   Align mounting screws (FF) to the keyholes on the fixture body (A) and screw the mounting finials (DD).
   NOTE: Ensure the connection is secured.

6. Turning Power On
   Turn power on at circuit breaker or replace the fuse.

7. Use The Sensor Cover
   At this time if the light is strong, please cover the sensor cover(GG), after 15 seconds the light is on, then the installation is correct.
   NOTE: If you want to use the DUSK TO DAWN function, please remove the sensor cover (GG) after commissioning the fixture is completed.

8. Changing Color Settings
   Choose your preferred color temperature between 2700K,3000K,3500K,4000K and 5000K with switch.

9. Applying Caulk
   To prevent moisture from entering the outlet box and causing a short, use caulk(not included) to outline the outside of the fixture’s backplate where it meets the wall, leaving a space at the bottom to allow moisture a means of escape.

TROUBLESHOOTING

DUSK TO DAWN OPERATION

• The light will turn on at dusk and remain on through the night until dawn. The light will remain off throughout the day, until dusk.

NOTE: To make sure this function works properly, always have the switch in the `ON’ position (including daytime).

CARE AND MAINTENANCE

• To clean, turnoff and wipe with a damp, non-abrasive cloth.

Limited Warranty

5 YEAR LIMITED WARRANTY: LEDVANCE warrants the Product to be free from defects in material and workmanship from date of purchase for the specified warranty period when used as directed. Failure to comply with Product warnings and instructions shall void the warranty. This warranty does not cover Product subject to accident, neglect, abuse, misuse, or acts of God, If Product fails to operate according to the warranty, return Product to place of purchase with proof of purchase date and LEDVANCE will replace with the same or similar Product free. LABOR IS NOT INCLUDED. LEDVANCE reserves the sole right to examine and determine whether the Product is defective. For additional information, contact contact 1-800 LIGHTBULB(1-800-544-4828);Email: lightbulb@ledvance.com.THIS IS THE EXCLUSIVE REMEDY AVAILABLE.LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXPRESSLY EXCLUDED. SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE . THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,INCLUDING THE WARRANTY OF MERCHANTABILITY OR FITNESS OF USE, WHICH ARE HEREBY EXCLUDED. IF UNDER APPLICABLE STATE LAW IMPLIED WARRANTIES MAY NOT VALIDLY BE DISCLAIMED OR EXCLUDED, THE DURATION IS LIMITED TO THE SPECIFIED WARRANTY PERIOD.

Questions, problems, missing parts? Before returning to your retailer, call our customer service at 1-800-544-4828 Monday ­ Friday 7:00 a.m. ­ 5:00 p.m. CST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>