SYLVANIA 4210521 4 Inch LED Microdisk Downlight User Manual

SYLVANIA 4210521 4 Inch LED Microdisk Downlight

Product Information

• Specifications:
  • Model: LEDMD4500ST9SC3WH A B
  • Color Temperature: 2700K, 3000K, 3500K, 4000K, 5000K
  • Operating Conditions: Indoor
  • Compliance: FCC Part 15, FCC Radiation Exposure Limits
  • Power Supply: 120V

Product Usage Instructions

• Installation:
  • To install the device on the ceiling:
  • Open the power supply box (CC) cover.
  • Feed the supply wire into the knockout hole using a 3/8 in. clamp connector (not included).
  • Make all connections inside the power supply box (CC) using the wire connectors (BB) provided.
  • Connect the 120V line (black) wire to the black wire.
  • Connect the neutral (white) wire to the white wire.
• Operating Instructions:
  • To operate the device:
  • Use the push button to cycle through different color temperatures: 2700K, 3000K, 3500K, 4000K, 5000K.
  • Cut Out Template:
  • Use the provided template to mark the pore size on the ceiling for installation.

Lighting Distribution

FAQs

• Q: What should I do if the device causes interference with radio or television reception?
  • A: If interference occurs, try reorienting or relocating the receiving antenna, increasing separation between equipment and receiver, connecting equipment to a different circuit, or consult a dealer or technician for assistance.
• Q: How do I ensure compliance with FCC radiation exposure limits?
  • A: Maintain a human proximity of not less than 20cm (8 inches) to the antenna during normal operation to avoid exceeding FCC exposure limits.

WARNING
Please Read All Instructions Before Attempting Installation

• Turn off electricity at the circuit breaker box (or main fuse box) before beginning installation by removing the fuse (or switching off the circuit breaker).
• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
• All electrical connections must agree with local codes, ordinances or the National Electric Code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140° F/60°C. Consult a qualified electrician before installation.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified, licensed electrician for information about proper grounding methods as required by the local electrical code in your area.
• If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and electrical rating required.

LEDMD4500ST9SC3WH

For warranty coverage, please register at www.ledvanceUS.com.

Preparation

• Before beginning assembly, installation or operation of the product, make sure all parts are present.
• Compare parts with the package contents list and diagram on the previous page.
• If any part is missing or damaged, do not attempt to assemble, install or operate the product.
• Contact customer service for replacement parts.

TOOLS REQUIRED

TOOLS REQUIRED (not supplied)

CONTENT

FCC

FCC STATEMENT
This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm(8 inches)during normal operation. That changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAN ICES-005 (B)

Installation

1. Turn Off the Power.
   • Before beginning the installation, make sure all power is off at the breaker box. Remove the disused existing bulb if necessary and remove the existing trim.
2. Cut a hole in the ceiling
   • Cut a 4.6 in. hole in the ceiling as round as possible using the template (AA) provided and a recessed lighting hole saw (not included)
   • NOTE: Before cutting, ensure that the space above the installed fixture is at least 3 in and the hole does not impinge on joists, pipework, cable or other building services.
3. Making the electrical connections
   • Open the power supply box (CC) cover.
   • Feed the supply wire into the knockout hole using a 3/8 in. clamp connector (not included) and make all the connections inside the power supply box (CC) using the wire connectors (BB) provided.
   • Connect the 120V line (black) wire to the black wire. Connect the neutral (white wire to the white wire.
   • NOTE: Carefully remove the knock-out with a slotted screwdriver or punch.
   • NOTE: For easier installation, separate the power supply box (CC) and downlight by disconnecting the tethered connectors.
4. Connect the tethered connector
   • Reconnect the tethered connector before restoring the power at the breaker panel.
   • To ensure proper connection, the arrows on the cable adapters must be facing each other. Screw on the fastener to secure the connection.
5. Installing the fixture
   • Hold the spring clips against the fixture body (A) and gently guide into the ceiling until the clips snap into place. The fixture body (A) should be flush with the ceiling.
6. Turning Power on
   • Turn power on at circuit breaker or replace the fuse.

Operating Instructions

Connecting Lamps

• After installation is done, turn the power ON.
• The product will start blinking slowly for about 30 seconds and pair together automatically.

Note: If the product doesn’t enter pairing mode, simply turn ON/OFF the wall switch of the group of products you want to pair together three times.
Changing Color Temperature:

• Select the desired color temperature by pressing the push button on one of the units.
•  All units will automatically follow and adjust to the same color temperature.

Adding Products to a Group:

• To add a unit to a group, press and hold the CCT button for 3 seconds on the unit you want to add to the group, and then press the CCT button on one unit from the group.

Unpairing Fixtures from Remote or Groups:

• Using the Wall Switch:
  • Turn the wall switch ON/OFF three times at a normal speed.
  • All units connected to the wall switch will pulse three times to indicate they are unpaired.
• For Individual Fixtures:
  • Press and hold the fixture switch for 6 seconds.
  • The fixtures will pulse three times to indicate they are ready for the next command.

Lighting Distribution

CARE AND MAINTENANCE

• To clean, turn off and wipe with a damp, non-abrasive cloth.

TROUBLESHOOTING

1. The light does not come on at all:
   • a) Make sure the wall switch and circuit breaker are on.
   • b) Make sure the wiring is correct.
2. The fuse blows or the circuit trips when the light is turned on.
   • a) Check for crossed wires, and ensure wiring is correct. If unable to fix any of the above issues, please consult a certified electrician.

LIMITED WARRANTY

5-YEAR LIMITED WARRANTY: LEDVANCE warrants the Product to be free from defects in material and workmanship from the date of purchase for the specified warranty period when used as directed. Failure to comply with Product warnings and instructions shall void the warranty. This warranty does not cover the Product subject to accident, neglect, abuse, misuse, or acts of God, If the Product fails to operate according to the warranty, return the Product to the place of purchase with proof of purchase date and LEDVANCE will replace with the same or similar Product free. LABOR IS NOT INCLUDED. LEDVANCE reserves the sole right to examine and determine whether the Product is defective. For additional information, contact 1-800 LIGHT- BULB(1-800-544- 4828);
Email: lightbulb@ledvance.com.THIS IS THE EXCLUSIVE REMEDY AVAILABLE. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS EXPRESSLY EXCLUDED. SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR ALLOW OR LIMITATION CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE OR PROVINCE. THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTY OF MERCHANTABILITY OR FITNESS OF USE, WHICH ARE HEREBY EXCLUDED. IF UNDER APPLICABLE STATE LAW IMPLIED WARRANTIES MAY NOT VALIDLY BE DISCLAIMED OR EXCLUDED, THE DURATION IS LIMITED TO THE SPECIFIED WARRANTY PERIOD.

Imported by

• LEDVANCE
  • 1100 Tyrone Pike
  • Versailles, KY 40383
  • 1-800-LIGHTBULB (1-800-544-4828)
  • www.ledvanceUS.com (US & Canada)
  • SYLVANIA is a registered trademark.

References

• LEDVANCE US and Canada | SYLVANIA General Lighting | Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>