LUMATEK ZEUS 600W 2.6 High Quality LED Horticultural Lighting Instruction Manual
- June 3, 2024
- LUMATEK
Table of Contents
- INTRODUCTION
- PRODUCT DESCRIPTION
- PRODUCT INFORMATION AND SPECIFICATIONS
- SAFETY RECOMMENDATIONS AND WARNINGS
- CONTENTS
- INSTALLATION
- PRECAUTIONS WHEN USING THE LED FIXTURE
- INSPECTION, MAINTENANCE, AND REPAIR
- STORAGE AND DISPOSAL
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZEUS 600W 2.6 High-Quality LED Horticultural Lighting
Instruction Manual
INTRODUCTION
Thank you for purchasing the Lumatek Zeus 600W 2.6 linear multi-light bar LED fixture. This manual describes how to install and use the Zeus fixture; please read this manual thoroughly before attempting to install or operate any Lumatek Zeus Series system. If you are not comfortable with the installation of high-performance lighting systems, you should seek the services of a qualified installation professional.
PRODUCT DESCRIPTION
The Lumatek Zeus 600W 2.6 LED is an electronic horticultural LED fixture using
a linear array design with six 100W ‘Full Spectrum’ LED light bars and an
intelligent driver making the fixture externally controllable & dimmable.
The ZEUS 600W 2.6 fixture is an ultra-high performance full-cycle top lighting
solution for commercial horticulture cultivation & indoor farming, with the
power and flexibility to scale from propagation and cloning through vegetative
growth to higher light intensities in bloom.
In this manual, the Lumatek Zeus 600W 2.6 LED will be referred to as: “the LED
fixture”.
PRODUCT INFORMATION AND SPECIFICATIONS
3.1 General Product Information
PRODUCT NAME | Zeus 600W 2.6 LED |
---|---|
PRODUCT CODE | LUMLED020 |
MANUFACTURER | Lumatek Ltd |
EAN | 5.06056E+12 |
PLUG TYPE | UK/EU |
3.2 Technical Specifications
PPF | 1570 µmol/s |
---|---|
EFFICACY | Up to 2.6 μmol/J |
SPECTRUM | Full spectrum |
LIGHT SOURCE | Higher spec LUMILEDS (W)& Osram (R) LED |
DIMENSIONS | 1091 x 1182.4 x 81.2mm |
WEIGHT | 13.5Kg |
LIFE SPAN | 60000H |
WORKING TEMPERATURE | -20º — +40ºC |
WORKING HUMIDITY | 20% – 90% |
WATERPROOF/DUSTPROOF | IP65 |
BEAM ANGLE | 120º |
MANUAL DIM/
EXTERNAL LIGHTING| 0-10V analog protocol
3.3 Fixture Dimensions
3.4 Spectral Quantum Distribution Graph
The Zeus Pro series use higher spec highly efficient top bin horticultural
white & red LEDs to create a balanced full spectrum of quality light ideal for
photosynthesis.![LUMATEK ZEUS 600W 2.6 High Quality LED Horticultural Lighting
- Figure 2](https://manuals.plus/wp-content/uploads/2022/10/LUMATEK-ZEUS- 600W-2.6-High-Quality-LED-Horticultural-Lighting-Figure-2.jpg)
3.5 Light distribution curve
3.6 Environment
The LED fixture is intended to be used in climate-controlled grow rooms and
indoor farms.
The product may be used in damp environments but may not be used in wet
environments or outdoors.
The product will operate in ambient temperatures from -10ºC to 40ºC but will
function at optimal levels between 20ºC to 30ºC.
The product will operate in 20% – 90% humidity, non-condensing.
3.7 Legal
This product is CE certified and compliant with LVD and EMC directive test
standards.
SAFETY RECOMMENDATIONS AND WARNINGS
Warning! Carefully read the warnings below before using or working with the product!
-
Always adhere to the local rules and regulations when installing or using the LED fixture.
-
Do not open or disassemble the LED fixture as it contains no serviceable parts inside. Opening or modifying the LED fixture can be dangerous and will void the warranty.
-
Do not use the LED fixture when either the LED fixture or its power cable are damaged. Replace the power cable with the correctly rated cable only.
-
Modifications to the cables can lead to unwanted electromagnetic effects which may make the product not comply with legal requirements.
-
Do not expose the LED fixture to:
Condensing humidity, heavy mist or direct spray;
Ambient temperatures outside the specified range;
Dust and contamination;
Direct sunlight during use or HID light may heat up the driver. -
Always disconnect the LED fixture from the mains before performing any maintenance.
-
Always allow for a cool-down period of at least 20-30 minutes before touching the LED light bars. Touching the LED bars when the fixture is lit or immediately after may result in burns!
-
Natural convection removes heat away from the heatsink. In order for the system to properly cool itself, at least 5cm of space is required between the fixture and the roof of your grow area. Do not use abrasive materials or aggressive cleaning agents to clean the LED fixture as this may damage the secondary optics. Instead, use a clean dry fabric/cloth.
-
Do not use the LED fixture near flammable, explosive, or reactive substances. The LED fixture can reach temperatures of 40ºC.
-
Do not use sulfur vaporizers or water misters.
-
The installation and use of the LED fixture is the responsibility of the end user. Incorrect use or installation can lead to failure and damage to the LED fixture. Damage to the LED fixture and electronic circuitry as a result of incorrect installation and use revokes the warranty.
CONTENTS
INSTALLATION
Warning! Mounting and installing the LED fixture must be in accordance
with the applicable local laws and regulations.
Warning! The installer is responsible for correct and safe installation.
Warning! Ensure the local cabling can support the voltage and current
requirements of the LED fixture.
Warning! Avoid coiled cables and keep mains leads separated to help
prevent electromagnetic interference.
Warning! Do not connect or disconnect the LED fixture under load.
6.1 Fixture assembly & installation
Connect Frame A and B to the support frame by pressing the button on the
frame connector and inserting it into the support frame socket and lock.
Ensure the button clicks into the hole socket to lock.
Connect Frame B to support frame end near LED driver power output & dimming
female connectors.
Note the direction when installing; the driver tray is on top when the fixture
is hung.
6.2 Connect the LED Light Bars
Warning! The light bars are shipped with protective plastic covers over
the diodes. Please ensure these protective covers are removed before
use!
6.3 Connect & disconnect the driver
The LED driver is fixed to the mounting bracket with retention screws through the bracket into the driver base plate. For greater flexibility, the driver can be disconnected from the fixture and used remotely using Lumatek 5m LED driver extension cables (sold separately).
To connect driver output and dimming control to the fixture, ensure the power
and dimming self-locking male connectors are correctly aligned with
corresponding female connectors on the driver and push them together until
click-locked.
To disconnect; turn the male connector anti-clockwise to unlock it and pull it
apart from the female.
6.4 Changing and replacing light bars and modular use
The LED fixture’s modular design uses an intelligent LED driver which can
decrease or increase power to match the amount of 100W light bars installed in
the fixture automatically. If not all light bars are required, the driver will
only draw the power required for the number of light bars connected eg if
three light bars are connected the
driver will only draw 300W to power them.
Warning! At least one light bar must be installed in the fixture before
switching it on.
6.5 Installing the fixture
Warning! Mount the system to something that can hold the weight of the LED
fixture.
Ensure all light bars are installed correctly and securely. Carefully turn the
fixture over and attach the metal
cable hangers to the mounting hooks. Hang the fixture in the required position
and height. For optimal performance; position the fixture 30 – 50cm above the
plant canopy for a 1.4 x 1.4m light spread. Ensure the fixture is hung
horizontally.
6.6 Connecting the manual dimmer or external lighting controller
The dimmer control or lighting controller is connected to the ‘SIG IN’
connector on the fixture frame. This enables light intensity (PPF output) to
be adjusted according to requirements. The LED fixture light intensity can be
adjusted without changing relative spectral power distribution or losing
efficiency.
Remove the dust cap and ensure male & female connectors are correctly aligned
and then push together until click-locked. To disconnect; turn the twist-lock
anti-clockwise and pull it apart.
6.7 Connecting fixtures in series for external control
For detailed instructions please refer to the Lumatek Control Panel manual.
Position and hang each fixture appropriately. Zeus series fixtures use 0-10V
signal protocol for control.
-
Connect controller output signal cable to fixture 1 SIGNAL IN connector.
Connect daisy-chain control signal cable (sold separately) from fixture 1 SIGNAL OUT connector to fixture 2 SIGNAL IN connector. -
Continue to connect fixtures in series for up to 100 fixtures per controller, see Fig.
6.8 Connecting the LED fixture to the mains
Warning! Make sure the mains power is switched off.
Warning! Ensure the power supply cable is not coiled and does not touch
any hot surfaces.
Warning! Connect the cables according to local rules, safety regulations,
and electrical codes.
Warning! If not using an external lighting controller ensure the external
switching gear can cope with the inrush current of the LED fixture. Always use
a timer contactor suitable for switching a capacitive load. Never use
household timers to switch the LED fixture!
Warning! Do not connect or disconnect the LED fixture under load.
Ensure the LED driver power supply cable self-locking female connector is
correctly aligned to the corresponding male connector on the driver and push
together until click-locked. To disconnect; turn the twist-lock connector
anti-clockwise to unlock and pull it apart from the driver.
Connect the mains power plug to the switching gear/power supply.
Switch on mains power.
PRECAUTIONS WHEN USING THE LED FIXTURE
Warning! Always ensure at least one light bar is connected to the fixture
before switching on. The Zeus fixture has an intelligent LED driver which can
increase or decrease power to match the number of light bars connected to the
system automatically.
Warning! Always wait 20 – 30 minutes for the LED light bars to cool down
before handling the fixture.
INSPECTION, MAINTENANCE, AND REPAIR
Warning! Disconnect the LED fixture from the mains before performing any
maintenance or repairs.
Warning! Do not connect or disconnect the LED fixture under load.
Warning! Do not open or disassemble the LED fixture, it contains no
serviceable parts inside. Opening the LED fixture can be dangerous and will
void the warranty.
Warning! Always wait 20 – 30 minutes for the LED light bars to cool down
before handling.
Caution! Do not clean the LED fixture with detergents, abrasives, or
other aggressive substances.
Regularly check the LED fixture for dust or dirt build-up. Clean if necessary.
Contamination may cause overheating and decreased performance.
Clean the outside of the LED fixture using a dry or damp cloth.
Regularly check the cables of the LED fixture to ensure it is undamaged.
STORAGE AND DISPOSAL
Store the LED fixture in a dry and clean environment, with an ambient
temperature of -25ºC to 55ºC.
The product must not be discarded as unsorted municipal waste but must be
collected separately for the purpose of treatment, recovery and
environmentally sound disposal.
WARRANTY
Lumatek warrants the mechanical and electronic components of their product to be free of defects in material and workmanship if used under normal operating conditions for a period of five (5) years from the original date of purchase. If the product shows any defects within this period and that defect is not due to user error or improper use Lumatek shall, at its discretion, either replace or repair the product using suitable new or reconditioned products or parts. In case Lumatek decides to replace the entire product, this limited warranty shall apply to the replacement product for the remaining initial warranty period, i.e. five (5) years from the date of purchase of the original product. For service; return the product to your shop with the original sales receipt.
References
- Sustainable LED lighting solutions | Philips lighting
- LUMATEK Professional Grow Lighting | Ballasts | Lamps | Reflectors
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>