tp-link TL-SX1008 8-Port 10G Multi-Gigabit Desktop Installation Guide

tp-link TL-SX1008 8-Port 10G Multi-Gigabit Desktop

Appearance

Front Panel

Rear Panel

Power

• On: Power on
• Off: Power off

Port LED

When one of the LEDs is on/flashing:

• On: Connecting to a device but no activity. Flashing: Transmitting or receiving data.
• Left LED (10G/5G):
• Green: Running at 10 Gbps.
• Amber: Running at 5 Gbps.
• The right LED (2.5G/1G/100M):
• Green: Running at 2.5 Gbps.
• Amber: Running at 100/1000 Mbps.

Note:
The images in this guide are only for example and may not reflect your actual experience.

Kensington Security Slot
Secure the lock (not provided) into the security slot to prevent the device from being stolen.

Power Socket
Plug the female connector of the power cord directly into the power socket and plug the male connector into an AC outlet. Make sure that the voltage of the power supply meets the requirement of the input voltage (100–240 V ~ 50/60 Hz).

Grounding Terminal
The switch already comes with a lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of the AC cord or with Ground Cable.

Installation

Method 1: Desktop Installation

Method 2: Rack Installation

Note:

• Leave 5 to 10 cm gaps around the devices for air circulation.
• Avoid placing heavy things on the device.
• Place the device with its bottom facing downwards.
• Mount devices in sequence from the bottom to the top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.

Connection

Specifications

General Specifications

Environmental and Physical Specifications

Safety Precautions

To avoid any device damage and bodily injury caused by improper use, you should observe the following rules.

• Keep the power off during the installation.
• Wear an ESD-preventive wrist strap, and make sure that the wrist strap has good skin contact and is well grounded.
• Use only the power cord provided with the switch.
• Make sure that the supply voltage matches the specifications indicated on the rear panel of the switch.
• Ensure that the switch is installed in a well-ventilated environment and that its ventilation hole is not blocked.
• Do not open or remove the cover of the switch.
• Before cleaning the device, cut off the power supply. Do not clean it with a waterish cloth, and never use any other liquid cleaning method.
• Place the device with its bottom surface downward.

Lightning Protection

Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000 °C. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. Ensure that the rack and the device are well earthed.

• Make sure the power socket has good contact with the ground.
• Keep a reasonable cabling system and avoid induced lightning.
• Use the signal SPD (Surge Protective Device) when wiring outdoor.

Note:
For detailed lightning protection measures, refer to the Lightning Protection Guide from the Related Documents of our website: https://www.tp-link.com/us /configuration-guides/lightning_protection_guide.

Installation Site

When installing the device on a rack or a flat workbench, attach much importance to the following items:

• The rack or workbench is flat, stable, and sturdy enough to support a weight of 5.5 kg at least.
• The rack or workbench has a good ventilation system. The equipment room is well ventilated.
• The rack is well grounded. Keep the device less than 1.5 meters away from the power socket.

Site Requirements

Temperature/Humidity

Keep the equipment room at an appropriate level of temperature and humidity. Too much or too little humidity may lead to bad insulation, leakage of electricity, mechanical property changes, and corrosion. High temperatures may accelerate the aging of the insulation materials, significantly shortening the service life of the device. To find out the best temperature and humidity conditions for the device, check the following table.

Clearness

The dust accumulated on the switch can be absorbed by static electricity and result in poor contact of metal contact points. Some measures have been taken for the device to prevent static electricity, but too strong static electricity can cause deadly damage to the electronic elements on the internal circuit board. To avoid the effect of static electricity on the operation of the switch, attach much importance to the following items:

• Dust the device regularly, and keep the indoor air clean.
• Keep the device well grounded and ensure that the static electricity has been transferred.

Electromagnetic Interference

Electronic elements including capacitance and inductance on the device can be affected by external interferences, such as conducted emission by capacitance coupling, inductance coupling, and impedance coupling. To decrease the interferences, make sure to take the following measures:

• Use the power supply that can effectively filter interference from the power grid.
• Keep the device far from high-frequency and strong-current devices such as radio transmitting stations.
• Use electromagnetic shielding when necessary.

Safety Information

• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Place the device with its bottom surface downward.
• The plug on the power supply cord is used as the disconnect device, the socket outlet shall be easily accessible.

Declaration Conformity

EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.

UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016. The original UK declaration of conformity may be found at https://www .tp-link.com/support/ukca/.

Contacts

• To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.
• For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.
• If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.

References

• 域名售卖
• TP-Link Community
• CE Regulatory Compliance | TP-Link
• TP-Link Product Support - Wireless Networking Equipment Support
• Regulatory Compliance | TP-Link
• lightning_protection_guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>