MONSTER MH22109 Open Ear HP Wireless Bluetooth Earphones User Guide
- June 5, 2024
- Monster
Table of Contents
MONSTER MH22109 Open Ear HP Wireless Bluetooth Earphones
Product Overview
- Earphones X 1 Pair
- Charging Stand
- USB-C Charging Cable
- Quick Start Guide and Warranty Letter
- Multi-Function Button (MFB)
- Microphone
- Indicator of headset
- Charging Contacts
- USB-C Charging Port
- Charging Stand Indicator Light
Power On/Off
The earphones will be turned on by pressing and holding the left and right MFB
buttons for 3 seconds. To turn off the earphones, press and hold the left or
right MFB button for 5 seconds.
Earphones Charging
Insert the attached USB-C cable into the charging stand. Then place the
earphones into the stand. The charging stand indicator light shows the battery
status, and will be always on after they are fully charged.
Pairing
The earphones will be turned on by pressing and holding the left and right MFB buttons for 3 seconds. Left and right earphones will be connected automatically within few seconds. Then “pairing” voice prompt will be heard. For new device connection, go to the Bluetooth settings on your device and set it to search for new devices (new Monster device). Once the earphones are paired to the designated device, you will hear “connected”. If the earphone has been paired, it will try to connect to the last connected device after turning on. To pair a new device, turn off the connection of the currently connected Bluetooth device, and then try again.
Volume Control
This earphone does not have a volume adjustment function. To adjust the
volume, after the Bluetooth earphone is successfully connected to the device,
use the volume adjustment button on the device to increase or decrease the
volume.
Call
Answer / End a call: Single tap the MFB.
Reject the call: Press and hold the MFB for 2 seconds.
Music
Play/Pause music: Single tap the MFB.
Previous song: Double-click the MFB button of the left earphone.
Next song: Double-click the MFB button of the right earphone.
Voice Control
When the earphone is connected to the phone, triple-click the MFB button of
the right earphone to enable or disable the voice assistant.
Enable/Disable Game Mode
Triple-click the MFB button of the left earphone to enable or disable the game
mode.
Reset
When both the earphones are turned off, press and hold the left and right MFB buttons for 10 seconds. You will hear a beep sound after the earphones have been restored to factory settings.
LED Indicator Guide
| Mode | Description | Voice Prompt |
|---|---|---|
| Power On | – | “Power On” |
| Power Off | – | “Power Off ” |
Pairing
| The LED indicator light of the main earphone flashes blue and red alternately, and that of the secondary ear flashes blue every 5 seconds.| “Pairing”
Connected
| After the connection is completed, the left and right indicator lights flash blue slowly.|
“Connected”
Earphones charging
|
When the earphones are charging, the red indicator lights are always on and turn off when they are fully charged.
|
–
Charging case
| During charging, the indicator light of the charging stand blinks, and it will be always on after the earphones are fully charged.|
–
Cautions
- Please place the earphones in the correct location (L/R) for normal charging.
- Replacement of battery (on your own) is not recommended.
- Do not expose battery (battery pack) to excessive heat such as direct sunlight or fire
FCC STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FCC ID: 2AVD2-MH22109
IC Warning statement:
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Measures:
Reorient or relocate the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help This device complies with part 15
of the FCC rules. Operation is subject to the following two conditions
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.