Yorkville YXL12P Powered Loudspeaker Enclosures User Manual
- June 5, 2024
- Yorkville
Table of Contents
Yorkville YXL12P Powered Loudspeaker Enclosures User Manual
Product Description
- Power & Mode LED – The power switch is on the rear panel and The Mode LED indicates when the unit is on.
- Mode Switch – EQ and tone settings.
- Concert: Best for live performances.
- Club: Ideal for program music playback.
- Monitor: Optimized for minimizing feedback when used as a stage monitor.
- Master Control – Independantly sets the audio level.
- Activity LED – Illuminates when signal is sent to the Master.
- Bluetooth® Pairing – Depress the Bluetooth® switch for about 4-seconds. The blue LED will flash when the unit is ready to be paired.
- Linking Multiple Units with Bluetooth® – Pair the first cabinet in the chain and ‘enable’ the onboard mixer (all other units should be unpaired). Link from the L/Link output to the recieving enclosure’s Main In jack using an XLR cable. If Stereo is desired, set the “paired” unit to Stereo Mode, the paired unit will play the Right and the ‘wired’ unit will play the Left.
- Onboard Mixer – The Mixer Enable switch turns the onboard mixer ‘on’ or ‘off.’ The onboard mixer should not be used when a source other than another YXL Series powered speaker (or similar) is connected to the LINK jack.
- Channel Level & Clip LEDs – The Level adjusts the input sensitivity and each channel’s signal being sent to the Master. The clip LEDs illuminate 3 dB before clipping and are affected by both the source’s gain and each channel’s level. NOTE: Bluetooth® level can be made on the source device.
- Channel 1 Mic / Instrument In – Dynamic, condenser or phantom powered microphones may be connected to the XLR input, phantom power is built-in. The 1/4-inch TRS input is optimized for guitars, basses or keyboards. Do NOT use both XLR and 1/4-inch inputs simultaneously.
- Channel 2 Mic / Line In – Dynamic, condenser or phantom powered microphones may be connected to the Mic input, phantom power is built-in. The 1/4-inch TRS input can be used with any line source with a line output. Do NOT use both XLR and 1/4-inch inputs simultaneously.
- Channel 3 Stereo Aux In – The 1/8-inch Line input jack is a ‘stereo’ input which properly sums the left and right signals from stereo sources such as MP3 players.
- Sub Switch – For operation with a subwoofer, shuts off the low boost and filters out signals below 100 Hz. This only affects the signals to the internal amplifier and does not affect signals passing through the Link connections.
- Main In – This input jack is the correct input to use when driving the YXL Series unit with an external mixer or from another YXL link output.
- Stereo/Mono Switch – Works in conjunction with the R/Link out jacks. If a single YXL Series Powered unit is used as the source, the originating unit will be mono or Left channel only, depending on the switch position. When in the out position (R), the Right channel is routed to the output of the link. When in the out position (R), the Left channel is routed to the output of the link. When the switch is selected, the output of the Link is Mono (stereo signals summed). This allows a pair of “Linked” YXL cabinets to give you stereo playback. Mono sources will still play normally through both cabinets.
To get the full Owner’s Manual please visit our website at http://www.yorkville.com/manuals/ or, if you need a printed version call 905-837-8777
IC Caution.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference,
- This device must accept any interference, including interference that may cause undesired operation of the device.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
REAL Gear.
REAL People
Canada
Voice:905-837-8481
Fax:905-837-8746
Yorkville sound
550 Granite Court
Pickering, Ontario
LIW-3Y8 CANADA
U.S.A
Voice:716-297-2920
Fax:716-297-3689
Yorkville sound
4625 Winter Industrial Estate
Niagara Falls, New york
14305 USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>