FALCON RIDGE JD-XUV25-TC01 John Deere Gator XUV 625i 825i Top Cap Canopy Instruction Manual
- June 3, 2024
- FALCON RIDGE
Table of Contents
2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of
John Deere Gator XUV 625i/825i Top Cap Canopy
JD-XUV25-TC01
JD-XUV25-TC01 John Deere Gator XUV 625i 825i Top Cap Canopy
CAUTION: Do not smoke inside the cab or expose the enclosure to direct
flames. The product is FLAMMABLE.
Be sure to read these instructions thoroughly before opening and installing
the enclosure. The installation is best done when the ambient temperature is
70°F or warmer. If installed in cold weather, warming the adhesive Velcro
strips before installation is recommended.
- Open the carton and remove the rolled Top Cap on a large flat surface that is clean and free of dirt.
- Check over the parts included in the carton with the parts list shown below:
Velcro Hook strips: ———————————————— 4 each 6” long Top:
Double-Sided Velcro w/ 30” Straps Attached —————— 4 each
30” Straps with grommets —————————————– 2 each
Top Panel ———————————————————— 1 each
Top Panel
a. If you have a Lexan windshield already installed on your vehicle you can
do one of two things. You may use the straps with Velcro sewn to one end and
wrap the roll cage under the windshield with the 6” adhesive Velcro strips.
Then wrap the double-sided Velcro sewn to the end of the strap around the
adhesive Velcro. If you choose you may also drill a 5/16” hole in the
windshield and bolt the strap with the grommet directly to the windshield. The
bolt should be installed from the inside out with a washer then strap, another
washer, and a locknut. Tighten all the way down and then loosen the locknut ½
a turn to free the strap to allow it to swing around to any position.
b. Now place the top over the entire vehicle, the front of the top is
identified by the sides not being as steeply curved, and begin by lacing the
front straps through the ladder lock buckles sewn to the front corners of the
top.
c. Now take two of the straps that are sewn to the double-sided Velcro and
wrap them around the rear bar of the roll cage halfway down the bar. The strap
should be on the outside of the bars.
d. Now run those straps up and through the ladder lock buckles sewn to the
rear of the top.
e. You now need to tighten and loosen the strap of the top so that it is
centered correctly and should cover the holes across the top of the
windshield.
f. If you were installing the Top by itself you would use the two remaining
straps with double-sided Velcro to attach the front. You may need to cut the
straps once fitted, do not cut off too much as you have nothing to hold on to,
and pull it tight the next time you go to install it. It is recommended to
leave about 6-8” hanging from the buckles.
Cleaning and Storage Recommendations:
-
Before removing the Mammoth Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild
liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage. -
It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.
-
A special cleaner conditioner is available from Mammoth Designs that will greatly increase the service life of the Cab Enclosure. In addition, if an additional hook and loop
sets are needed, they can also be ordered.
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from the date the item is received. You MUST package the product
exactly as it was originally packaged from the factory to get a full refund
for the product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes.
Lay all the windows on top of each other with the canvas folded in between and
the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory-new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE it if you have any intentions of
returning the item. Refund/ replacement of a windshield will only be processed
on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject to a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, the credit will be issued to
the original credit card/ payment method used for the purchase. Outbound
shipping and return shipping costs will not be refunded. Please allow 4 to 6
weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields!
Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops, and/or windshield due to defects of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Thank you,
Falcon Ridge
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>