MONSTER MLB-1033-RGB LED Light Strip User Guide

MONSTER MLB-1033-RGB LED Light Strip

SAFETY

WARNING: When using outdoor use products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal lnJury, Including the following:
Keep these Instructions

• Uncoil the light strip before use

• Do not drop, puncture, or disassemble this product

• DO not use this product in any way other than what is outlined in this guide

• Do not attach this product to the ceiling or to the floor  Do not submerge the strip or the power supply unit in water
  The power adapter must be connected to a GFCI protected hocxJed flush type cover plate receptacle marked “Wet Location” while in use outdoors

• Avoid long exposure to direct sunlight, which may cause damage

• Do not use this product in small, enclosed locations that could limit the flow of air or trap excess heat

• Do not expose this product to open flames or use near fire

• Do not use the product in a strong magnetic field

• Do not use this product for emergency l@hting/exits

• Do not allow small children to operate or install this device unsupervised

• Use a clean, soft cloth to clean – do not use any corrosive cleaners/oils

WHAT’S IN THE BOX

1. Neon Indoor/Outdoor LED Light Strip (16.4ft/5m)
2. Mounti Clips+ Screws
3. Fov,,er Adapter (24V l.5A. 6ft/1.8m cord)
4. Quick Start Guide

WHAT DD YOU NEED?

1. Cellphone or tablet with
   Android 6.0 or higher / iOS l 0 or higher

2. NI-Fl router with an INTERNET connection

3. NI-Fl 2.4GHz 802.lln

4. Philips head screwdriver

Before setup, make sure your ph:lne Is connected to the 2.4GHz WI-Fl network that your Neon will be placed on.
You may also need to turn on location to find nearby devices. TIP: Do you know your Wi-R rietworl< name and password? Write It down now if it’s hard to remember.

ANYTHING ELSE?

Your Neon LED Light Strip Is very f!eXble and can be used to write messages or draw glowing images. If your design ideas are ambitious. try drawing it out on paper first and planning whe1e the mounting clips should be placed.

SETUP MPLETE SETUP BEFORE INSTALLATION

1. sTEP 1
   Remove your Neon and all components from the box.

2. STEP 2
   Download u MCINSTER SMART app from the App Store (for ! Phones) or Google Play Store (for Android phones).

3. STEP 3
   Make sure your stories or tablet is successfully connected to the 2.4GHz WI-Fl network that your Neon will be placed on.
   Open u MDNSTER’ SMART app and create an account by following the on-screen instructions.

4. STEP4
   It is recommended to first pair Neon in a location indoors and close to your router BEFORE installation.
   Plug the power adapter into the port on the cable and connect the other end to a powered wall outlet. Toe LED Light Strip Will to begin blinking rapidly when it has entered pairing mode and is ready to pair. Pairing Modes
   EZ MOOE -RAPIDLY BLINKING LED (default)
   EZ Mooe iS is the default mode for quick and easy pairing setup,
   AP MOOE -SLOWLY BUM<ING LEO
   k.c= Pcm Mc.ce 1s a Scrondary setup that can tielo Rome:t In mi ,ed net;vo Follow the on-screen step b,, step 1nsuu:t1ons.
   Press and hold the button for 5-6 seconds to enter pairing mode or change between pairing modes.
   MCf’\Sler =mart dev.::es only v.ork on a 2.4GHz Wl-FI networl<. Many near h:>rre WI-F, networ1<s are led netwo1<s that are set ID SGHzbvrnafautt (ex: AT&T Venzon) and you may need t0 use AP pairing mode to connect If you still have-, difficulty conical your Internet Se<vlCe Pro, clear asS1Stancew1lh 2.4GHz network setup

5. STEP 5 In the MONSTER SMART app, select the ” In the upper right corner of the home screen to add a new device, and then select “Lighting (WI-Fi)” to add your device.

6. If needed. cl1ek “Net Pamng Mode” 1n the upper right lo switch the default EZ pairing mode for 2.4GHz Wi-Fi networks to AP mode for mixed WI-Fl networks.
   STEP 6 Confirm that the LED indicator is RAPIDLY blinking. Confirm that the network displayed is your 2.4GHz WI-Fl network. then enter your ‘NI-Fi password and click ·confirm·
   Confirm that the LED indicator is SLOWLY blinking. Confirm the neN/Erik Is your mixed WI-Fl network. enter your Wi-Fi password and click “Confirm”. Follow the on-screen instructions to set up your device via wireless aa:ess point.
   Once complete, your device will be connected to the network Confirm or change the settings for your device ard then click “Done”, YoUI Neon is row setup and you can proceed to Installation.
   You can now use the app to add voice control ( see PB 8 ). and adjust settings. create custom lighting effects. set schedules.

INSTALLATION

1. STEP 1
   Determine where you will install the Neon. Make sure the location Is close enough to a power source for the cord to reach without becoming a tripping hazard.
   Before Installing. try out different designs with your Neon on the floor or a table to decide what you would like to create!

2. STEP 2
   Using the Included mounting clips and screws. ard a Phillips head screwdriver (not included), mount the Neon in the desired location. For best results place one clip at least every 12 Inches to secure the entire light strip evenly.
   TIP: Mo.-e some mounting dips closer to the corner to better secure the strip around turns, use fewer on straight areas.

3. STEP 3
   Once Installed. plug the power adapter into the port on the cable and screw on the water-tight locking cap until secure. Connect the other erd to a powered wall outlet. and you’re done! (Outdoors this must be a GFCI-protected outlet.)
   NOTE: If desired, you can cut the light strip to a shorter length. Howe,er, IF THE PRODUCT HAS BEEN CUT IT WILL NO LONGER BE WATERPROOF or covered under warranty.

HOW TO USE

Your LED Light Strip can be easily controlled by the controller. using u MCINSTER SMAAT app to access advanced and customizable lighting effects. or by using a compatible voice assistant product for hands-free operation. (seepage B)

CONTROLLER TROUBLESHOOTING

HAVE TROUBLE WITH SETUP?

Don’t return this product to the retailer, we’re here to help. Please call for customer support: 866-246-2008

• Why is my device failing to connect to my Wi-Fi network7

  • Make sure your phone or tablet is successfully connected to the 2.4GHz WI-Fl network that your device will be placed on.
  • You may first need to enable and allow location services on your phone or tablet to find nearby devices.
  • If your Wi-Fi network is a mixed 2.4GHz/5GHz network, try using AP pairing mode for better results.
  • If you still have issues with your mixed network, you may need to access your router settings and/or call your Internet Service Provider to create a separate 2.4GHz network.

• Can I cut this LED Light Strip7
  Yes. If desired, you can cut the light strip to shorter lengths by cutting on the designated scissors marks. However, once cut, the strip will no longer be water resistant or covered under warranty.

• Can I attach additional LED Light Strips to this one7
  This strip is not designed with an expansion plug, but you can easily group multiple strips together in the app in order to control them all as one. Click on the menu button in the upper right corner and then click “Create Group” to group your devices.

• ls this product water-resistant?

  • Yes, ensure that the power adapter connection is tightly sealed.
  • Yes, but the power adapter must be connected to a GFCI-protected hooded flush type cover plate receptacle marked “Wet Location” while in use outdoors.
  • Yes, but the power adapter is NOT water-resistant. Do not submerge the strip, controller, or adapter in water.

For other frequently asked questions please visit our website at www.monsterilluminessence.com

VOICE CONTROL OPTIONAL

AMAZON VOICE CONTROL SETUP
Make sure your Amazon Alexa device is installed and setup

1. Open the Alexa app and go to Skills in the menu
2. Search for and choose II MCINSTER’ SMART
3. enable the Skill and authorize your account using your login information
   NOTE: Use the same login information that you used to create your Monster Smart account At any time, go to the Alexa app to set nicknames and rooms for your devices. You can also rename devices in the Monster Smart app.
   Using the name Neon, or the name you assigned your Neon, you can ask Alexa to control your device, just say “Alexa,” and ask: “Turn on my Neon”, “Set my Neon to blue”, “Set my Neon to 50% brightness”, and more!

GOOGLE VOICE CONTROL SETUP
Make sure your Google Assistant device is installed and set up.

1. STEP l: Open the Google Home app, go to the Home menu, and tap the”+” button
2. STEP 2: Click “Set up device”
3. STEP 3: Click “Have something already set up 7”
4. STEP 4: Search for and choose II MCINSTER’ SMART and authorize your account using your login information
   NOTE : Use the same login information that you used to create your Monster Smart account At any time, go to the Google Home app to set nicknames and rooms for your devices. You can also rename devices in the Monster Smart app.
   Using the name Neon, or the name you assigned your Neon, you can ask your Google Assistant to control your device, just say “Hey Google” and say: “Turn on my Neon”, “Set my Neon to blue”, “Set my Neon to 50% brightness”, and more!

SIRI VOICE CONTROL SETUP Requires iPhone running iOS 12 or later.

1. STEP l : Open the 11 MCINSTER’ SMART app and go to the “Smart” menu, tap the “+” button to create a new Tap To Run Smart Scene
2. STEP 2: Tap “launch Tap To Run” and fill out the information
3. STEP 3: Once your Smart Scene is created and saved, click the button that appears at the bottom of the screen that says “Add to Siri” to open the list of options
4. STEP 4: Select your new Tap To Run Smart Scene from the list and click “Add to Siri”
5. STEP 5 : Create a custom phrase to say to Siri to run your Smart Scene (this can be any verbal command) Now Siri can use your voice and custom verbal command to turn your device on or off, activate your last used lighting scene, adjust Neon at the same time as your other smart devices, or whatever you’ve set up as your Tap To Run Smart Scene.

NOTES
WATER-RESISTANCE
Your Neon is water-resistant and is suitable for both indoor and outdoor use. The power adapter is NOT water-resistant. To ensure maximum water protection:

• Ensure that the power adapter connection is tightly sealed.
• The power adapter must be connected to a GFCI-protected hooded flush-type cover plate receptacle marked “Wet Location” while in use outdoors.
  Do not submerge the strip, controller, or adapter in water. Do not cut, puncture, or otherwise damage the strip.

FCC Compliance

This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for comp Ii ance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interferencetoradioor television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  – Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement
To satisfy FCC’s RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this
distance is not recommended.

ISEDC Warning

This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

The device is compliance with RF exposure guidelines, use can obtain Canadian information on RF exposure and compliance. The minimum distance from body to use the device is 20cm.

1 YEAR LIMITED WARRANTY

Jem Accessories, Inc. Limited Warranty Policy for Monster Smart Products Last Updated: March 27, 2020
This limited warranty contains important information about your rights and obligations, as well as limitations and exdusions that may apply to you.

1. WHAT THIS LIMITED WARRANTY COVERS; PERIOD OF COVERAGE Jem Accessories, Inc (“Jem Accessories”), 32 Brunswick Ave, Edison, New Jersey, USA, warrants to the owner of the endosed Monster Smart-branded product
   contained in this box (“Producn will be free from defects in materials and workmanship for a period of one year. Notwithstanding the foregoing, the Warranty Period for a factory refurbished Product is one (1) year, even if installed by a professional. If the Product fails to conform to this Limited Warranty during the Warranty Period, Jem Accessories will, at its sole discretion, either (a) repair or replace any defective Product or component; with proof of purchase using original documentation. Repair or replacement may be made with a new or refurbished product or components, at Jem Accessories’s sole discretion. If the Product or a component incorporated within it is no longer available, Jem Accessories may, at Jem Accessories’s sole discretion, replace the Product with a similar product of similar function. This is your sole and exclusive remedy for breach of this Limited Warranty. Any Product that has either been repaired or replaced under this Limited Warranty will be covered by the terms of this Limited Warranty for the longer of (a) ninety (90) days from the date of delivery of the repaired Product or replacement Product, or (b) the remaining Warranty
   Period. This Limited Warranty is not transferable from the original purchaser to subsequent owners.

2. TOTAL SATISFACTION RETURN POLICY If you are the original purchaser of the Product and you are not satisfied with this Product for any reason, ou may return tin ts original condition to the retailers in compliance with the retallersretum policy. S.WARRANIY CONDITIONS HOW 1o Gtl SEVICE IF YOU WANTTo cLAIM UNDER THIS LIMITED WARRANTY Before monteriuminessence.com/supoort  during the Warranty Period to provide notice of your warranty daim and describee the alleged allure, and (b) comply with Jem Accessories (or Ms authorized distributor s return shipping instructions emACessores w navenowilrany oigjatos win recto eruerottOeermines, jtisresonabie except with respect to any ineligible Product or products shipped internationally, for which the owner will bear all TED Subject to: (a) modifications, alterations, tampering, or improper maintenance or repairs b) handling storage, installation, testing, or use not in accordance with any quicK Start guide, manual or other instructions provided by Jem hurricane; or (in) any non-em Accessories branded hardware products, even if packaged or sold with Jem Accessories Delaware ns time watany does not WEr COsuma0Ie parts, including batteries, unless image due o OeiCs materials r workmanship of tneProdut,or software eenpatagd or sold wth product someone’s or software can impair the Product’s performance and may invalidate this Limited Warranty .

3. DSLAINEROF WAHNANIIES Egypt as stated above in this limited warranty, and to the maximum extent permitted by applicable law, LEM Accessories disclaims all express, implied, and statutory warranties and conditions wth respect maximum extent permitted by applicable law, Jem Accessories also limits the duration of any applicable implied WarsornOTs me duration tons impaired wärraniy. .

4. UMIAION F DAMAGES In addition to the above warranty dbdlamers, in no event w Jem Acesones be liable tor arising from or relating to this limited warranty or the product, and Jem Accessories total cumulative liability arising from orreaedo tns limed warranty r Ue product W not exceed une mount actually pair 10r the product oy the original purchase. information (‘product information” regarding our LEM Accessories products or other peripherals. connected to your UABAUTY The Jem Access ine se riluminess s )p products (product peripherals”j, The type of product peripherals that may be connected to your product may change from one of you mng neEnereity ore disarmed above, aplo0uct inronen0n5 proven for your information will be available arcuate unreliable or that rmditinfirematicn.or.of the services oe verdict will M provide safety in your home. You use all product information, the services, and the product at your own discretion and Risa. TOU Wi De solely respond DIe or land jem Acessores s0aiany and ai 0s, ldbinly, or damages, during t you wing, ures, recently,homeprdut pUperheas, complex, more de a Ratner and provided by the services is not intended as a substitute for direct means of obtaining the information. For example, a notification provided through the serve is not intended as a substitute or audible and VISIble medications in the home & yOUR BICHTS ANO THIS TE A dntos diam state. gal rights. You may also have other legal rights that vary by state, province, or jurisdiction. Likewise, some of the limitations in this Limited Warranty may not apply in certain states, provinces or jurisdictions. The terms of this Limited Warranty wl apply to the extent permitted by applicable law. For a tul description of your legal rights you should refer to the laws applicable in your fic le you need to start a warranty claim for your Monster Smart device, please reach out to (Customer Support by emailing CUstomersenvicemonsterilluminessence.com or calling our support number at 866-246-2008. Please allow 7-10 business days to process warranty claims. (Customers located outside of the U.S. will be esporsioie Tor dl snapping costS.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>