FALCON RIDGE AL-LM500-FC04 American Landmaster LM500 Full Cab with Aero-Vent Poly Windshield Instruction Manual

AL-LM500-FC04 American Landmaster LM500 Full Cab with Aero-Vent Poly Windshield
Instruction Manual

LM500-FC04 American Landmaster LM500 Full Cab with Aero-Vent Poly

Windshield

2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of American Landmaster LM500
Full Cab with Aero-Vent Poly Windshield
AL-LM500-FC04
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. The cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the LM500 Full Cab with Poly Windshield. The installation is best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature prior to installation.

1. Carefully open the carton and remove the enclosure on a large flat surface that is clean and free of dirt.
2. Check over the parts included in the carton with the parts list shown below:
   Adhesive Velcro Hook Strips:
   Soft Doors**** “| “| “| “|  20 each————3″
   ---|---|---|---|---
   “| “| “| “|    2 each————4″
   “| “| “| “|    2 each————13″
   “| “| “| “|    2 each————14″
   “| “| “| “|    2 each————33″

Rear Window
Adhesive Velcro Hook Strips:

Top Cap

If any parts are damaged or missing please contact customer service at606-845-7439.
Soft Doors:

3. Begin by holding the door up to the frame and attaching it using the double-sided Velcro strips sewn perpendicular to the edge of the door. At each of the double-sided strips take one of the 3″ adhesive Velcro strips and adhere it to the inside of the frame. Then wrap the double-sided strip around it so that the adhesive strip holds it firmly in place. The following diagrams show how it should look.

4. Next, take the 33″ and 14″ adhesive Velcro strips and run them down the back of the roll cage facing towards the rear of the vehicle. You will see two double-sided Velcro tabs sewn along the back of the doors. The adhesive strips must be aligned so that both tabs can attach to them. See the photos on the next page.

5. Now do the same for the 13″ and 4″ Tabs on the front lower portion of the door. REAR WINDOW:

6. Begin by placing the 38″ adhesive Velcro strips across the top of the roll cage. Make sure to place it on top of the bar. The photo on the next page shows how it should look.

7. Next, place it on the two Velcro tabs down the sidebars. Start at the top at the crossbar and work your way down the tube.

8. The bottom of the Rear Window is held in place by the 39″ adhesive Velcro strip attached to the plastic piece separating the bed from the seats. See the photo on the next page. POLYCARBONATE WINDSHIELD

9. Install using the directions included with the windshield. Do Not install the top brace.
   TOP CAP

10. After you have installed your Lexan windshield installed on your LM500 you can take the straps with grommet holes in them and install them on the middle bolt of the windshield. Put the grommet through the bolt and reattach. The strap with the loop should look like the photo below.

11. Next, take the other two straps with Velcro sewn on one end and wrap them around the roll cage in the rear just under the seat belt. You will need to pull the double-sided tab up and wrap the Velcro around the bar letting the strap come out by the seat belt winder. See the photo on the next page.

12. Now place the top over the entire vehicle, the front of the top is identified by the sides not being as steeply curved, and begin by lacing the front straps through the ladder lock buckles sewn to the front corners of the top. The diagram below shows how to use a ladder buckle. Now run those straps up and through the ladder lock buckles sewn to the rear of the top.
    You now need to tighten and loosen the strap of the top so that it is centered correctly.

13. Now install the top brace of the windshield over the top of the front of the top cap. This seals it off so that less air gets into the cab. Take a small knife and poke the material where each hole is so that a bolt can get through. See the photo below.

Cleaning and Storage Recommendations:

1. Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
2. It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.
3. A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered.
   Thank you for your purchase!

Return Policy

If for any reason you choose to return this product it must be returned within 30 days from the date the item is received. You MUST package the product exactly as it was originally packaged from the factory to get a full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the windows on top of each other with the canvas folded in between and the paper (if available) on both sides of thewindows.
All returned products will be inspected upon arrival at the production facility and must be in unused, factory new condition to receive a refund – a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you must first call them and see what their return policy is. Once your item reaches our production facility, our customer satisfaction team will inspect your item to ensure unused, factory new condition.
NOTE: All windshields must be returned with the original protective film intact and not removed. Do NOT REMOVE if you have any intentions of returning the item. Refund/ replacement of a windshield will only be processed on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your returned item arrives back factory fresh, and in new resalable condition (any returned items that have been used, altered or damaged in any way will not be subject for a refund.) All contents including instruction manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM factory new condition will be approved. Once returned items are received, credit will be issued to the original credit card/ payment method used for the purchase. Outbound shipping and return shipping cost will not be refunded. Please allow 4 to 6 weeks for your refund to be processed.

Warranty

To The Owner of this Product:
Thank you for purchasing one of Falcon Ridge Enclosures, Tops &/or Windshields! Below are the terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or windshield due to defect of the product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>