Evvr SRHW01 In-Wall Relay Switch Instruction Manual

: June 5, 2024
: EVVR

Table of Contents

Complete Accessories Include
Setup Code Product Introduction
Technical Specifications
Installation Instructions
Operating Instructions
Troubleshooting
Legal Notice
Certifications (regional)
FCC Statement
Disposal Instructions
Warranty Policy
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

In-Wall Relay Switch
Smart Relay
Instruction Manual
Rev. A-031821 P/N SRHW01

*Please see separate Evvr Smart Switch Sub-Assembly manual for complete instructions.

Complete Accessories Include

Evvr SRHW01 In Wall Relay Switch - box

Setup Code Product Introduction

Smart Relay uses Wi-Fi technology and may be used in different loads, including incandescent lamps, halogen lamps, LED lamps, and fluorescent lamps. It is small enough to be installed in light switch boxes and the body of most light fixtures. This device uses Apple HomeKit technology for remote control and inter-operation.

Technical Specifications

Model Number	SRHWO1
Input Voltage	AC 85V-245V
Max. Load Power	AC 110V/300W

Evvr SRHW01 In Wall Relay Switch - fig1

Panel Connection port

Evvr SRHW01 In Wall Relay Switch - fig2

Wire Connection port

Installation Instructions

Caution: Read this manual before attempting to install the device! Using this product in a manner other than intended voids your warranty. Further, Focalcrest is NOT liable for any damage incurred with the misuse of this product.
Caution: All installations of this device should be performed by a qualified or licensed electrician!
Caution: The product must be installed on a 10A line.
Caution: Metal casings, mirrors, electrical appliances, etc., may affect, reduce, or interfere with wireless communication.

Warning: Turn OFF electrical power from the breaker box or electrical service panel before installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH, or LOSS/DAMAGE OF PROPERTY.

Caution:
Use this product in an indoor environment.

1 Connect wires per wiring diagram as follows
Caution: If you have purchased a Smart Switch Sub-Assembly to use with it, please follow the installation instructions on the Smart Switch Sub- Assembly manual.
With Smart Relay, you can turn a traditional lamp into a HomeKit smart lamp. It is recommended to install Smart Relay near the lamp.

You can choose one of the two diagrams below to connect the wires according to your installation environment.

Evvr SRHW01 In Wall Relay Switch - fig4

2 Fix Smart Relay on a flat, cleaned surface

Stick the foam pad to the recommended position on the Smart Relay and then place the relay on a flat, cleaned surface.
Turn ON electrical power and check if the wires are connected correctly. If wires are properly connected, the indicator light will come on while the light(s) connected to the switch is turned on.

Operating Instructions

Important: The In-Wall Relay Switch can be controlled from an iOS device.
Note: The indicator will blink blue every five seconds when the device is in setup mode.
To control this HomeKit-enabled accessory, the latest version of iOS or iPadOS is recommended.
A customer who owns an Apple TV (4th generation or later) with tvOS 10 or later, an iPad with iOS 10 or later, or a HomePod or HomePod mini can control HomeKit-enabled accessories away from home and automatically through triggers such as time of day, location, sensor detection, or the action of an accessory.

Add Smart Relay to Apple HomeKit

Set the Smart Relay into setup mode by short press the RESET button. (When the device is not added to the Homekit network, it enters setup mode for 10 minutes each time it reboots)| Open the Apple Home app and select “Add Accessory”| Locate and scan the HomeKit setup code on the device or on the front page of this manual, then follow the instructions in the Apple Home app.

Unpairing Smart Relay from Wi-Fi Router
Press and hold the RESET button for more than 2 seconds (the indicator light will flash once)
Restore Smart Relay to factory Settings
Press and hold the RESET button for more than 5 seconds (the indicator light will double-flash once)

Indicator Light Status

Color	Activity	Wi-Fi Connection	HomeKit Connection
Blue	Glowing
Red	Glowing
Red	Flashing
Red	Double flashing

Type of Connected Switch

Double-click the reset button to switch between the three switching modes.

Switch	Indicator
toggle switch (device changes status when switching changes status)	the

indicator will blink purple once
toggle switch (contact closed – ON, contact opened – OFF)| the indicator will blink purple twice
momentary switch| the indicator will blink purple three times

Troubleshooting

Q1 Smart Relay pairing failed.
The device may be too far from the gateway/coordinator or routing device, or there may be interference in the current network environment. Add routing devices or bring devices closer to the gateway/coordinator.
The device is already joined to another gateway. Please restore the device to its factory default.
Q2 Cannot be controlled by gateway/coordinator or other HomeKit devices.
The device may be installed in the wrong location, too far from the gateway or routing device, or there may be signal interference. Please check whether there is strong electromagnetic field equipment near the wireless switch and check whether the equipment is installed in a closed metal housing or in a closed concrete wall. Add routing devices or bring devices closer to the gateway/coordinator.
Q 3 The light turns off automatically after a short period of time (approximately 2½ minutes or 150 seconds).
The power of the light may exceed the maximum power (AC 110V/ 300W, AC 220V/600W). Please check whether the power of the light exceeds the maximum power.
Q4 In case of power loss while the lights were on, the light status is on when power is restored?
Yes. The device will record the status of the light, and after the device is powered off, re-powering will restore the state before the device was powered off.

Legal Notice

Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Apple, HomeKit, HomePod, HomePod mini, iPad, iPhone, and Apple TV are trademarks of Apple Inc., registered in the U.S. and other countries and regions.

Certifications (regional)

FCC ID: 2AYEW-SRHW01

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

– Reorient or relocate the receiving antenna.
– Consult the dealer or an experienced technician for help.
Important Announcement Important Note Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Disposal Instructions

This product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.